Genlantis TempZAP ETZT100 User manual

Automatic Infrared Thermometer
INTRODUCTION
The TempZAP™ Automatic Infrared Thermometer with 12 to 1 distance-to-sight ratio and
temperature alarm offers fast response and high accuracy. Advanced features include high and
low temperature alerts, adjustable temperature alert limit, 100 memory bank, automatic
temperature readings, auto power-off. Careful use of this meter will provide years of reliable
service.
The TempZAP™ Automatic Infrared Thermometer is the ultimate in convenient, safe, accurate,
and fast temperature monitoring. The provided tripod stand makes setup and placement of the
thermometer very easy and convenient.
1
Voice on/off switch
4
°F/°C
selection button
7
Infrared sensor
10
On/Off switch
2
Page
down
5
Speaker
8
Battery compartment
11
USBC power input
3
Page
up
6
LCD screen
9
¼ inch tripod connector
12
Wall hanging port
Key Features
Specifications
12:1 Distance
-
to
-
sight ratio
Measurement method
Infrared, no
-
contact
1% basic accuracy
Measurement distance (min.)
3 inches (8 cm)
Rapid
detection function
Measurement range
32
-
122
°
F (0
-
50
°
C)
Precise n
oncontact measurements
Operating Temperature
50
-
104
°
F (10
-
40
°
C)
Automatic power
off
Memory size
100 measurements
Low and
High temp alerts (visual and audible)
Automatic power off
30
seconds
Backli
t LCD
Power modes
USB
5V
or 2 x AAA batteries
(3V)
Automatic data
h
old
TempZAP Thermometer weight
6.4 oz (180 grams)
User
-
selectable °C or °F units
TempZAP Thermometer size
6.7 x 4.0 x 1.32 in. (170 x 100 x 5 mm)
Adjustable
temperature alert settings
Tripod Range
27
-
84 inches (0.7
-
25.13 meters)
Catalog #
Description/Content
Contents
ETZT100 TempZAP™ Automatic
Infrared Thermometer
1.
TempZAP
Thermometer
2. Tripod stand
3. USB-A/USB-C power cable
4. Wall installation kit
Related
Products
Catalog #
FirstResponder® Sterilizer, 110V
E4110FRS
FirstResponder®
Handheld
Sterilizer
E600
UVCH
FirstResponder® Portable Sterilizer (cordless)
E600UVCP
SteriZAP™ UV
-
C Room Sterilizer, 110V
E500
UV
CT
1
2 3
4
5
6
8
7
9
10
11
12
ON
OFF

TempZAP™ Automatic Infrared Thermometer Manual
VKM200903 Genlantis Page 2 of 2
6044 Cornerstone Court West, Bldg. E. San Diego, CA 92121  Toll Free [phone]  U.S. & Canada [phone]  www.first-responder.com
2020 Genlantis and Gene Therapy Systems, Inc.
USE INSTRUCTIONS
1. Unbox the TempZAP™ Thermometer and insert two (2) AAA batteries (not included) into the battery compartment [8], or
connect the TempZAP Thermometer to a USB power source using the included USB cable.
2. Hang the TempZAP Thermometer on a wall using the provided wall installation kit, or install TempZAP Thermometer to the
included tripod as follows:
a. remove the plastic screw protector on top of the tripod
b. connect the tripod screw to the ¼ inch connector [9] at the bottom of the TempZAP thermometer.
3. Turn the TempZAP Thermometer on by toggling the ON/OFF switch [10] to the left.
NOTE: For first time use, allow the TempZAP Thermometer to equilibrate to the place of use for about 30 minutes.
4. When a person approaches the TempZAP Thermometer at 6 inches (15 cm) or closer, the unit will turn on (if it was in power-
saving mode) and will be ready to take temperature within 1-2 seconds.
5. To take a person’s temperature, put forehead or wave hand at 3 inches (8 cm) or less.
6. The TempZAP Thermometer will automatically display the temperature and give a voice command as follows:
Temperature
R
ange
Voice Command
LCD Screen Color
Below 93.2°F (34
°C)
“Please retest”
Yellow
93.2
–
99.14°F (34
-
37.3°C)
“Normal Temperature”
Green
99.3
–
107.5 (37.4
-
41.9°C)
“High Temperature”
Red
7. Screen display guide:
BUTTON FUNCTIONS
1. Short press the Voice on/off Switch [1] to toggle between voice or silent; long press this button to clear the memory.
2. To review stored temperatures, use the page down [2] or page up [3] to move up or down the memory slots.
3. Short press the °F/°C button [4] to toggle between Fahrenheit or Celsius; long press this button (5 seconds) to toggle between
English and Chinese voice command languages.
4. To change temperature alert settings, simultaneously press the Voice on/off Switch [1] and the °F/°C button [4]
a. F1 will appear shortly, followed by the high temperature alert default of:”37.3 C” (99.14°F)
b. To change this value, use the Page Down [2] or Page Up [3] buttons;
c. Press the °F/°C button [4] to exit.
Auto detect function
indicator
Normal temperature
graphic
Battery level indicator
Voice
command
indicator
°F/°C indicator
Memory slot Indicator
(up to 100)