GEONAUTE KEYMAZE 500 HIKE User manual

KEYMAZE 500 HIKE
KEYMAZE 700 TRAIL

CONTENTS __________
GENERAL PRESENTATION 2
1/ Button functions
2 /Screen icons
3/ USB connection
4/ Tec nical information
FIRST USE 4
1/ Firmware update
2/ Initial adjustments
a/General adjustments
b/User settings
c/Zone settings
d/Display settings
e/Capacity
f/Calibration
g/Pairing the heart rate monitor belt
h/Updating the KEY AZE
FREE MODE 10
1/ Setting t e parameters of t e session
2/ Starting my session
3/ Das board
4/ Pop-up menu
NAVIGATION MODE 14
1/ Create a route
a/Download a route from Quechua Club
b/Create a route in the Geonaute Software
c/Rework a route from a previous session using Geonaute Software
d/Rework a route from a previous session using the KEY AZE
2/ Start a guided route
3/ Route option
4/ T e guiding system
a/Start my session
b/Dashboard
c/Pop-up menu
5/ Point of interest
a/ ark a POI during a session
b/Go to a POI
c/Coordinates
6/ End of session
a/On the KEY AZE
b/Importing a route from the KEY AZE to the Geonaute Software
c/Syncing the POI(s)
COMPLEMENTARY INFORMATION 23

Reference Version number Application date
KEYMAZE 500HIKE 1 17/11/2011 2/24
KEYMAZE 700TRAIL
GENERAL PRESENTATION
1/ Button functions
2 / Screen icons
The battery icon indicates how much charge you have left in the battery. An
icon filled with 4 bars indicates that the battery is full
GPS signal icon
Activation icon: the icon flashes before starting the session. The icon is
continuous during the activity and the gathering of information
Pause icon: The icon flashes when the stopwatch is stopped. You are no longer
recording any information at this point
Pop-up menu icon
Icon for displaying information pages (page 1 of 4 here)
Press for 3 seconds, to
switc the KEY AZE on/off
If the device is switched on,
press briefly to
activate/deactivate the
back-lighting
Access to the pop-up
menu while the session
is paused
Closes the current page
and returns to the
previous page
During t e activity:
Allows you go to
different screens
(information
pages/map/altitude
information)
Confirms a selected option or confirms
the data entered.
Starts/pauses a session or a route
The arrows allow you to navigate
between the different menus.
Zooms in/out of the map view

Reference Version number Application date
KEYMAZE 500HIKE 1 17/11/2011 3/24
KEYMAZE 700TRAIL
3/ USB connection
Recharging and the transfer of data are done using a USB cable.
The device takes an estimated 3 rs 30mins to charge.
oDATA TRANSFER WITH THE PC
oRECHARGING THE DEVICE
a) Remove the cap marked with the "USB" icon at the top of the KEY AZE.
b) Plug in the connector provided.
c) Plug the other end into one of your computer's USB ports.
4/ Tec nical information
Tec nical data
KEYMAZE500 KEYMAZE700
Number of Points of Interest:
100 100
Recording time:
20hrs (2s/point) 30hrs (2s/point)
Number of routes t at can be
memorised:
10 10
Pixels (L x W):
128 x 96 pixels
Weig t:
61g
Waterproof:
IPX7 (Depth of 1m for 30mins)
Size:
50.6 x 66.7 x 17.1 (L x D (Φ) x H in millimetres)
Operating temperatures:
-10° to 60° C
GPS precision:
+/- 5 with good satellite reception
Satellite reception time:
Less than a minute when ready
Operating voltage:
Continuous 5V input voltage
Battery:
800mAh Lithium ion polymer
Barometer:
Yes
Battery life:
15 hours (estimated) with back-lighting screen
OFF
11 time (estimated) with back-lighting screen ON
ANT+ protocol:
No Yes
GPS:
SiRF Star III LPx
C arge time:
3hrs 30mins
Waterproof:
IPX7 (immersion at a
depth of 1m for 30
minutes)
Position accuracy
+/- 5 with good
satellite reception
Satellite reception
time:
Less than 1 minute
when ready

Reference Version number Application date
KEYMAZE 500HIKE 1 17/11/2011 4/24
KEYMAZE 700TRAIL
FIRST USE
1/Firmware update
Your KEY AZE is a product that evolves over time.
In order to have the latest version, update it before using for the first time.
Step 1: download the latest version of Geonaute Software at www.geonaute.com
(direct link: http://www.geonaute.com/files/software/GeonauteSoftware.exe)
The Geonaute Software is only compatible with PC
Step 2: install Geonaute software

Reference Version number Application date
KEYMAZE 500HIKE 1 17/11/2011 5/24
KEYMAZE 700TRAIL
Step 3: add your product
Go to equipment -my devices -add device -select KEY AZE Quechua 500 or 700
Step 4: Once you have switched the KEY AZE on and connected it to the PC, click on the image of
the product and confirm with OK
Step 5: Click "Update Firmware" and follow the instructions.
Confirm with OK.

Reference Version number Application date
KEYMAZE 500HIKE 1 17/11/2011 6/24
KEYMAZE 700TRAIL
2/ Initial adjustments
a/ General adjustments
Language - choice: English, Portuguese, Dutch, German, Italian, Spanish, French.
Time - the time is automatically received by the GPS signal (Greenwich eridian). You can however
adjust the time difference to match your time zone.
Unit - You can choose between the following two measurement systems when setting the units of
measurement: metre/gram or feet/pounds (imperial units)
Beep – OFF/button+popup/alerts alone
Nig t mode – Off/On
The night mode keeps the back-lighting of the screen on throughout the whole exercise session
During your exercise session, press the Power button briefly to activate/deactivate the back-lighting.
b/ User settings
ONLY FOR THE KEY AZE 700:
HR max: this is the maximum heart rate at which your heart can beat, (by default, it is estimated
using the formula 220 - the age) – choice from 61 to 240 bpm
HR min: this is the heart rate at rest, it is recorded in the morning when waking up or after lying
down for 3 min. – choice from 40 to 240 bpm
c/ Zone settings
This allows you to set yourself a working session for training, keeping to a certain pace throughout
the session or for reasons of safety.
You set a minimum and a maximum and your KEY AZE warns you when you are going outside these
limits.
- eart rate - choice of the zone in bpm (only on the KEY AZE 700) Should you choose the heart
rate zone, you will not be able to choose the speed zone.
- speed zone
3 speeds: /on the flat in km/hr
/ascending speed in m/hr (metre per hour)
/descending speed in m/hr (metre per hour)
Gender – ale/female
Age – choice from 10 and 99 years
Weig t – choice from 30 to 150 kg / 66 to 253 lb
Size - from 130 to 230 cm / 51 to 91 inches

Reference Version number Application date
KEYMAZE 500HIKE 1 17/11/2011 7/24
KEYMAZE 700TRAIL
- OFF: the zones are deactivated
d/ Display settings
This menu allows you set the number of pages, the number of views as well as the values available
during your exercise. It is also possible to set these different screens using the Geonaute Software
and then transfer them to the KEY AZE:

Reference Version number Application date
KEYMAZE 500HIKE 1 17/11/2011 8/24
KEYMAZE 700TRAIL
e/ Capacity
Battery life: 0-15hr
Storage capacity:
0 to 361 hours depending on the
sampling selected
Sampling of points:
From 1 point per second to 1 point every 10 seconds
Value by default: 1 point every 2 seconds
T e sampling involves recording t e coordinates of your route at regular time intervals.
f/ Calibration
Press the OK button after the animation to launch the calibration.
The sat nav must be held in a HORIZONTAL position and turned through 360º until the connection
icon is full and the sat nav confirms that it is properly calibrated. The compass gives you a proper
heading even when the user is stationary. Great care must be taken when calibrating the device. If
not, the directions shown will be unreliable.
Even though the KEY AZE regularly carries out a self-calibration you can manually calibrate the
altitude before starting an activity.

Reference Version number Application date
KEYMAZE 500HIKE 1 17/11/2011 9/24
KEYMAZE 700TRAIL
g/ Pairing t e eart rate monitor belt
(KEYMAZE 700 only)
To detect the signal from the belt, it must be fitted to the chest with the sensors moistened. If after
several attempts the belt cannot be recognised, try pairing using this mode.
Each sensor (accelerometer or heart rate monitor belt) has a unique identification number that cannot
be changed. When the belt is stimulated (moisten then fit to the chest) it automatically transmits its
identification number to the watch.
The "Pairing" function enables the KEY AZE to detect the stimulated belts that are within a 10-metre
radius and memorise their identification number. You must move away from any other sensors in the
vicinity during this phase to prevent your belt from pairing with them.
By default the KEY AZE 700 is supplied paired the HR monitor belt contained in the package. It is
therefore not necessary to use the "pairing" function before using it for the 1st time.
However, the "pairing" function may be used when you wish to use another belt or when the belt can
no longer be recognised.
/ Updating t e KEYMAZE
This mode updates your KEY AZE using the Geonaute Software interface allowing you to benefit from
the latest improvements.
To do this, you need to be connected to your PC using the cable provided and the Geonaute Software
application must be active.