GeoVision GV-3D People Counter V2 User manual

Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
User’s Manual V1.00
GV-3D People Counter V2
3DPC2V10-A

© 2017 GeoVision, Inc. All rights reserved.
Under the copyright laws, this manual may not be copied, in whole or in part,
without the written consent of GeoVision.
Every effort has been made to ensure that the information in this manual is
accurate. GeoVision, Inc. makes no expressed or implied warranty of any kind
and assumes no responsibility for errors or omissions. No liability is assumed
for incidental or consequential damages arising from the use of the information
or products contained herein. Features and specifications are subject to
change without notice.
Note: No memory card slot or local storage function for Argentina.
GeoVision, Inc.
9F, No. 246, Sec. 1, Neihu Rd.,
Neihu District, Taipei, Taiwan
Tel: [phone]
Fax: [phone]
http://www.geovision.com.tw
Trademarks used in this manual: GeoVision, the GeoVision logo and GV
series products are trademarks of GeoVision, Inc. Windows is the registered
trademark of Microsoft Corporation.
August, 2017

Contents
Firmware and Software Compatibility................................................................................ ii
Chapter 1 Introduction ..................................................................................................... 2
1.1 Packing List ............................................................................................................. 2
1.2 Options.................................................................................................................... 2
1.3 Overview ................................................................................................................. 3
1.3.1 Bottom View ............................................................................................. 3
1.3.2 Rear View................................................................................................. 4
Chapter 2 Getting Started................................................................................................. 5
2.1 Connecting the Device............................................................................................. 5
2.2 Restoring to Factory Default Settings ...................................................................... 6
2.3 Wall / Ceiling Mount................................................................................................. 7
Chapter 3 The Web Interface............................................................................................ 9
3.1 Accessing the GV-Web Report Lite.......................................................................... 9
3.2 Setting the GV-3D People Counter V2....................................................................10
3.2.1 General Settings......................................................................................11
3.2.2 People Counter Settings ..........................................................................20
3.2.3 Report to Other Servers...........................................................................22
3.3 Accessing People Counting Data............................................................................23
3.3.1 Device .....................................................................................................23
3.3.2 Group ......................................................................................................25
3.3.3 Log ..........................................................................................................27
3.3.4 Query.......................................................................................................28
Chapter 4 Auxiliary Device Connectors .........................................................................31
PIN Assignment..................................................................................................................31
Chapter 5 GV-IP Device Utility.........................................................................................32
5.1 Installing GV-IP Device Utility .................................................................................32
5.2 Setting the GV-3D People Counter V2....................................................................33
Appendix.............................................................................................................................35
Optimal Installation..........................................................................................................35
Detection Limitations.......................................................................................................36
i

ii
Firmware and Software Compatibility
The GV-VMS and GV-Web Report compatible with GV-3D People Counter V2 are listed below
Model GV-VMS GV-Web Report
GV-3D People Counter V2 V1.00 V16.10.3.0 or later V2.2.6.0 or later
Note: For showing the people counting data on GV-VMS’s live view, see 3.18 Video Analysis
by Camera in GV-VMS User’s Manual.

2
Chapter 1 Introduction
The GV-3D People Counter V2 can count and analyze the number of people passing by the
designated area at high precision counting accuracy. With its Power over Ethernet and
user-friendly interface, the counter is simple to use and easy to install. You can look up neatly
compiled people counting data in chart analysis with the support of GV-Web Report Lite, its
built-in Web interface. In addition to its sleek and stylish design, the counter also supports the
I/O devices and GV-GPS Receiver for accessing people counting data remotely.
Figure 1-1

2
1.1 Packing List
1. GV-3D People Counter V2
2. SDHC Micro SD card
3. Ceiling Mount Kit
4. Wall Mount Kit
5. Installation Sticker x 2 (Wall mount /
Ceiling mount)
6. Screw x 4
7. Anchor x 2
8. Documents Download Guide
9. Warranty Card

2
1.2 Options
Optional devices can be purchased separately for GV-3D People Counter V2. Contact your
dealer for more information.
Options Details
GV-GPS Receiver
Receive the GPS signals for 3D People Counter
positioning.
GV-Web Report
Through a Web browser, the GV-Web Report keeps track
of and analyzes the people counting results and shows
the latitude and longitude from up to 1000 units of GV-3D
People Counter V2s.
GV-PA191
The GV-PA191 is a Power over Ethernet (PoE) adapter
designed to provide power to the IP device through a
single Ethernet cable.
GV-POE Switch
The GV-POE Switch is designed to provide power along
with network connection for IP devices. The GV-POE
Switch is available in various models with different
numbers and types of ports.

Introduction
1
1.3 Overview
This section identifies the components of the GV-3D People Counter V2.
1.3.1 Bottom View
1
Figure 1-2
No. Name Function
1 Lens Fixed lens for capturing people image.
3

4
1.3.2 Rear View
1 2 3 4
Figure 1-3
No. Name Function
1 Ethernet Port A plug for PoE (IEEE 802.3af).
2 Default Button It resets all configurations to their factory settings.
3 Terminal Block The connectors for the sensor input, alarm output and GPS
receiver.
4 Memory Card Slot Insert a micro SD card (SD/SDHC/SDXC/UHS-I, Class 10) to
store recording data.

Getting Started
2
Chapter 2 Getting Started
2.1 Connecting the Device
The instructions below describe the basic connection required to operate GV-3D People
Counter V2.
12
Figure 2-1
1. Connect to a standard network cable or PoE for power supply and Internet connection.
2. Insert a micro SD card.
Note: GV-3D People Counter V2 only supports PoE. You may purchase GV-PA191 PoE
adapter to connect to your router. See 1.2 Options.
5

6
2.2 Restoring to Factory Default Settings
If for any reason the GV-3D People Counter V2 is not responding correctly, you can restore
the GV-3D People Counter V2 to factory default settings.
Green LED Default Button
Figure 2-2
1. Press and hold the Default button on the rear panel.
2. Release the Default button when the green LED stops blinking. The GV-3D People
Counter V2 will automatically reboot after loading default.
Note: The power should always be on during the process of loading default.

Getting Started
7
2
2.3 Wall / Ceiling Mount
You can use the Wall / Ceiling Mount Kit to mount GV-3D People Counter V2 on a desired
location.
Wall Mount Ceiling Mount
1. Remove the GV-3D People Counter V2’s outer case.
Figure 2-3

8
2. Secure the desired mounting kit to the designated position with 2 screws.
Figure 2-4
3. Put the outer case back.
Figure 2-5
4. Put the installation sticker to the wall with the arrow pointing up.
5. Drill 2 holes according to the sticker and insert the 2 screw anchors to the 2 holes.
6. Secure the the GV-3D People Counter V2 to the wall with 2 long screws.
7. Optionally install the ground wire with the screw as shown below:
Ground Wire
Figure 2-6

The Web Interface3
Chapter 3 The Web Interface
After installing the GV-3D People Counter V2 on the network, you can access GV-Web Report
Lite tolookup counting data. The GV-Web Report Lite is a Web server built in the GV-3D
People Counter V2.By default, when the GV-3D People Counter V2 is installed to a LAN
with the DHCP server, the GV-3D People Counter V2 uses a dynamic IP address assigned
by the server. If installed in a LAN without the DHCP server, the default IP address
192.168.0.10 will be applied.
3.1 Accessing the GV-Web Report Lite
System Requirements
To access GV-3D People Counter V2 through Web browser, ensure your PC is in good
network connection, and use the following web browser:
Microsoft Internet Explorer 10 or above
Logging In
1. In your Web browser, type the IP address or the domain name ofthe GV-3D People
Counter V2 in the Location / Address field.
Figure 3-1
2. Select a different Language if needed.
3. Type the ID and password. The default ID and password are admin.
4. Type the characters shown in the image and click Login.
9

10
3.2 Setting the GV-3D People Counter V2
Once you have logged in to the GV-Web Report Lite, click the Setup tab on the top to see the
page below. Clicking Reset at the bottom-right corner will reset the Setup page back to default
values.
Figure 3-2
[Live View] Draw a box on the live view to mark the boundary of the detection zone. Subjects
moving across the blue box toward the red arrow will be counted as Out. Subjects moving
across the blue box toward the green arrow will be counted as In. To change the direction of
the arrows, you can click the Change button after Direction Change to the right of the live view.
You can also conceal certain area on the live view to reduce false counting data by selecting
Mask Position under Detect Area..
Live View: Click to see the live image of the detection area captured by the infrared
sensor of the GV-3D People Counter V2. The live image is in black and white.
REC: Records the live view for 30 seconds. Only one video can be stored in the SD card
at a time. The existing recording will be overwritten by the new recording.
Download Recorded File: You can download the recorded file and provide the recording
to service personnel for troubleshooting.

The Web Interface3
3.2.1 General Settings
Under the live view, the following setting tabs are available: User, DDNS, SMTP, Export, SCH,
IP, SD, FW, Time, MEM, GPS, I/O, FTP.
[User]
Machine Name: Change the display name of the GV-3D People Counter V2 if necessary.
Login Name / Password: Change the login name or password for accessing the GV-3D
People Counter V2 if necessary. The default login name and password are admin.
Port: Modify the port or keep the default 30003. When connecting to other servers, GV-3D
People Counter V2 must use the same port as the servers.
Confirm Pw: Type the password again for changing the above settings or password.
Figure 3-3
11

12
[DDNS]
DDNS (Dynamic Domain Name System) provides a convenient way of accessing GV-3D
People Counter V2 with a dynamic IP address. DDNS assigns a domain name to the GV-3D
People Counter V2, so that the Administrator does not need to check if the IP address
assigned by DHCP Server or ISP (in xDSL connection) has changed.
Figure 3-4
1. Click Register to register a GeoVision DDNS Server or apply for a Host Name from other
DDNS service provider’s website.
2. Type the Host Name used to link to the GV-3D People Counter V2.
3. Type the Name and Password used to enable the service from the DDNS.
4. Click Connect.
[SMTP]
You can receive a report of the counting results by e-mail. First, set up your mail server on this
page and then go to the Export tab to enable the function.
Figure 3-5

The Web Interface3
SMTP Server: Type your SMTP Server’s URL address or IP address.
Port: The default port for most SMTP servers is 25. However webmail Yahoo and Hotmail
generally use differently SMTP port. In this case, check your e-mail provider for the SMTP
port number.
Sender Email: Type the sender’s e-mail address.
Login Required: If your mail server needs login authentication, select the checkbox and
type your login username and password.
Use SSL: Select this option if the SMTP server needs a secure connection.
Login Username: If the SMTP Server needs authentication, type the valid username.
Login Password: If the SMTP Server needs authentication, type the valid password.
Test Email: Click to send a test e-mail to the chosen e-mail address. You can set up the
e-mail address in Recipient E-mail under Export.
[Export]
To automatically receive an e-mail report of the counting data, select Enable Auto Export
and type the Recipient E-mail. Use the Auto Export Time drop-down list to select what time
to receive the report and click Apply. Make sure you set up the mail server under the SMTP
tab.
Figure 3-6
13

14
After you have completed the Export settings, you shall receive the report in a zip file at the
appointed time. The report in the zip file is as the figure below.
Figure 3-7
[SCH]
To enable people counting only during certain time of the day, click the checkbox and specify
a time period. You can set up to 3 schedules.
Figure 3-8

The Web Interface3
[IP]
According to your network environment, select a Network Type.
DHCP: Select ifyour network environment has a DHCP server which can assign a
dynamic IP to your device. By default, this option is enabled.
Static IP: To set up a fixed IP address, type the IP address, subnet Mask, DNS and
Gateway of the static IP.
PPPoE: Establish the connection to your ISP. In Username / Password, Type the
username and password provided by the ISP to establish the connection. However, if the
IP address provided by your ISP is dynamic, use the DDNS function to obtain a domain
name linking to the unit’s changing IP address before enabling the PPPoE function. For
details on Dynamic DNS Server Settings, see DDNS in 3.2.1 General Settings.
Figure 3-9
[SD]
You can see the size of the inserted SD card, size of space used by current database and size
of free space. To clear the content of the SD card, click Reset Database.
Figure 3-10
15