GeoVision GV-IP Speed Dome User manual

Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use. ISD220200-QG-D
Quick Start Guide
GV-IP Speed Dome

© 2014GeoVision, Inc. All rights reserved.
Under the copyright laws, this manual may not be copied, in whole or in
part, without the written consent of GeoVision.
Every effort has been made to ensure that the information in this manual is
accurate. GeoVision, Inc. makes no expressed or implied warranty of any
kind and assumes no responsibility for errors or omissions. No liability is
assumed for incidental or consequential damages arising from the use of
the information or products contained herein. Features and specifications
are subject to change without notice.
GeoVision, Inc.
9F, No. 246, Sec. 1, Neihu Rd.,
Neihu District, Taipei, Taiwan
Tel: [phone]
Fax: [phone]
http://www.geovision.com.tw
Trademarks used in this manual: GeoVision, the GeoVision logo and GV
series products are trademarks of GeoVision, Inc. Windows and Windows
XP are registered trademarks of Microsoft Corporation.
May2014

Contents
1. Introduction............................................................... 1
2.......................... 2
2
................................ 2
................................ 3
4
................................ 5
ount........... 5
Mount..................... 7
.............................. 10
11
...............................11
ng In................. 12
.............................. 14
.............................. 16
2.8 Configuring a Preset Position............................................... 18
2.9 Configuring a Sequence Route ............................................ 20
2.10 Configuring a Cruise .......................................................... 23
2.11 Configuring an Auto Pan..................................................... 24
2.12 Configuring a Tour.............................................................. 26
2.13 Upgrading System Firmware .............................................. 28
2.14 Restoring to Default Settings.............................................. 30
. GV-SD220 / SD220-S.......................
2.1 Packing List ...........................................................................
2.1.1 Indoor GV-IP Speed Dome...........
2.1.2 Outdoor GV-IP Speed Dome ........
2.2 Overview................................................................................
2.3 Installation..............................................
2.3.1 Indoor GV-IP Speed Dome: Hard-Ceiling M
2.3.2 Outdoor GV-IP Speed Dome: Wall
2.4 Connecting the Cables...........................
2.5 Accessing the Camera ..........................................................
2.5.1 System Requirements ..................
2.5.2 Looking Up the IP Address and Loggi
2.6 The Web Interface..................................
2.7 The PTZ Control Panel...........................
i

2.14.1 Restoring All the Settings.......................................... 30
30
ings Only............... 31
3. G 32
.............................. 32
.............................. 32
.............................. 33
.............................. 34
3.3 Installation............................................................................ 35
e Mount ................ 35
Pendent Mount..... 38
.............................. 40
.............................. 42
42
gging in.................. 43
3.6 The Web Interface................................................................ 45
3.7 The PTZ Control Panel......................................................... 46
3.8 Configuring a Preset Position............................................... 48
3.9 Configuring a Sequence Route ............................................ 50
3.10 Configuring a Cruise .......................................................... 53
3.11 Configuring an Auto Pan..................................................... 55
3.12 Configuring a Tour.............................................................. 57
2.14.2 Restoring System Settings Only ...............................
2.14.3 Restoring PTZ Configuration Sett
V-SD200 / SD200-S...............................................
3.1 Packing List ...........................................
3.1.1 Indoor GV-IP Speed Dome...........
3.1.2 Outdoor GV-IP Speed Dome ........
3.2 Overview................................................
3.3.1 Indoor Speed Dome Mount: Surfac
3.3.2 Outdoor Speed Dome Mount: Mini
3.4 Connecting the Cables...........................
3.5 Accessing the Camera ...........................
3.5.1 System Requirements ................................................
3.5.2 Looking up the IP Address and Lo
ii

iii
60
3.14 Restoring to Default Settings.............................................. 62
3.13 Upgrading System Firmware ..............................................

1. Intr
de. In the following
sections, you will be guided through the basic installations and
io V GV-SD200/GV-SD200-S.
led tion, ser’s Manual on the
re C
oduction
Welcome to the GV-IP Speed Dome Quick Start Gui
configurat ns of the G -SD220/GV-SD220-S/
see GV-IP Speed Dome UFor detai informa
Softwa D.
Model Application Description
GV-SD220 Indoor
GV-SD220-S Outdoor
2 MP H.264, 20x / 30x optical
zoom, 12x digital zoom, WDR Pro
GV-SD200 Indoor
GV-SD200-S Outdoor
2 MP H.264, 18x optical zoom, 8x
digital zoom, WDR Pro


2. GV-SD220 / SD220-S
2.1 Packing List
2.1.1 Indoor GV-IP Speed Dome
•Indoor GV-IP Speed Dome •Hard-Ceiling Cover
te•Mounting Pla
•GV-IP Speed Dome
Software CD
•GV-NVR Software DVD

GV-SD220 / SD220-S
2
2.1.2 Outdoor GV-IP
•Outdoor GV-IP Speed Dome
Speed Dome
•Pendant Tube
•Hex Keys x 2 •M6 Screws x 3
•Desiccant pack x 4 •GV-IP Speed Dome
Software CD
•GV-NVR Software DVD
3

2.2 Overview
1
2
3
4
5
6
No. Name Description
1. e factory default values.
to Default Settings.
ault Restores all the settings to th Def For details, see 2.13 Restoring
2. Status The status LED turns green when the power is on and
fades when the camera is ready for use.
3. Power The power LED turns green when the power is on.
4. ACT The ACT LED flashes orange light upon data
transmission.
5. Link The Link LED turns green with Internet connectivity.
6. Memory
Card Slot Insert a micro SD/SDHC card to store recording data.
4

GV-SD220 / SD220-S
2
2.3 Installation
There are multiple ways to install the GV-IP Speed Dome. Only the
standard installation methods are introduced in the Quick Start Guide. For
GV-SD220/220-S IP
Speed Dome, Chapter 5, GV-Mount Installation Guide on the Software CD.
2.3.1 Indoor GV-I eiling Mount
details on optional installations, see Installing the
P Speed Dome: Hard-C
Required Items
•Indoor packing (supplied)
•ceiling screws x 3 (user-prepared)
1. Secure the mounting plate to the ceiling with self-prepared screws.
5

2. Secure the indoor GV-IP Speed Dome to the mounting plate.
A. Loosen the screw on the mounting plate
B. Align the camera to the mounting plate and rotate the camera
body to the right.
C. Tighten the screw.
3. Put on the hard-ceiling cover.
Note: Cut away a side of the cover if you want to run the cable through.
6

GV-SD220 / SD220-S
2
2.3.2 Outdoor : Wall Pendant Mount GV-IP Speed Dome
Requir
ed
Items
•O
ut
do
or
pa
cki
ng
(s
up
pli
ed
)
•C
eili
ng
sc
re
ws
x
4
(u
se
r-p
re
pa
re
d)
7

1. Insert a. the desiccants to the camer
IMPORT he desiccants in the GV-IP SpeedANT: Be sure to conceal t
Dome wit he desiccant pack.hin 2 minutes f opening to
A. Remove the camera cover using the supplied hex key.
8

GV-SD220 / SD220-S
2
B. Insert two desiccant packs to the indicated places.
C. Follow ste ecure the camera cover with the supplied
hex key.
As mble the camera wi the pendant tube.
Thread the c able through the pendant tube.
. Rotate the and lock it to the pendant tube.
p 1A to s
2. se th
A. amera c
B camera
C. Secure the camera to the pendant tube with the supplied M6
screws.
9

2.4 Connecting the Cables
er, microphone, speaker, and
d Dome. The Data Cable is illustrated as
With the Data Cable, you can connect the pow
I/O devices to the GV-IP Spee
below.
I/O Wires
Microphone
Power Adapter
Speaker
Ethernet
No. Wire Definition
1rm In 1Orange Ala
2Yellow Alarm In 2
3Green Alarm In 3
4Blue Alarm In 4
5Pink Ground
6Purple Alarm Out
7White Alarm Out Open
8Gray Alarm Out Close
10

GV-SD220 / SD220-S
2
2.5 Accessing the Camera
2.5.1 System Requirements
T Web browser, ensure your
PC is in good network connection and use one of the following web
•Microsoft Internet Explorer 7.x or later
•
•
•
o access GV-IP Speed Dome functions through
browsers:
Google Chrome
Mozilla Firefox
Safari
Note:
1. For users of Internet Explorer 8, additional settings are required.
For details, see Appendix C.For more details, see 1.2 System
Requirements, GV-IP Speed Dome GV-SD220 User’s Manual on
the Software CD.
2. With non-IE browsers,
A. Motion Detection, Text Overlay, two-way audio and GPS
map settings are not supported.
B. The Play function is only available on the live view window.
C. RTSP streaming must be kept as enabled.
11

12
2.5.2 Looking Up the IP Address and Logging In
By def igned by the
DHCP this case, the
default ow to look up
the dyna
1. ware CD.
ault, the IP address of your GV-IP Speed Dome is ass
server unless your router does not support DHCP. In
IP address will be 192.168.0.10. Follow the steps bel
mic IP address.
the SoftInstall the GV-IP Device Utility program from
Note: The PC installed with GV-IP Device Utility must be under the same
LAN with the camera you wish to configure.
2. On the PC desktop, select Start, select Prog
Device Utility to execute the program. The
wind
rams and select GV IP
GV IP Device Utility
ow appears and automatically searches for the GV IP devices
on the same LAN.
3. Click the Name or Mac Address column to sort.
4. Find the Mac Address of the camera to see its IP address.

GV-SD220 / SD220-S
2
5. To login, type the IP address in the browser. The login page appears.
he default ID and password admin and click Apply to
en accessing the GV-IP Speed Dome for the first time,
6. Type t log in.
7. Wh you must
er to allow a one-time installation of GeoVision
A veX component onto your computer.
set your brows
cti
Nf your support DHCP, the default IP address willote: I router does not
be 192.168.0 ggested to modify the IP.10. In this case, it is strongly su
a ddress conflict with other GeoVision IP device onddress to avoid IP a
th LA IP Address in 2.1 Lookinge same N. For details, see Changing the
Up the IP Address, GV-IP Speed Dome GV-SD220 User’s Manual on
the Software CD.
13

2.6 The Web Interface
12
11
123 4 5 6 78
10
9
No. Name Description
1 Play Plays live video.
2 Stop Stops playing video.
3 Microphone Talks to the surveillance area from the local
computer.
4 Speaker Listens to the audio around the camera.
14

GV-SD220 / SD220-S
2
Name DescriptionNo.
5 Snapshot Takes a snapshot of live video.
6 File Save al computer.Records live video to the loc
7 Full Screen
Right-click the image
shot, Full Screen,
Lens Dewarping, PIP,
s.
Switches to full screen view.
to have these options: Snap
Resolution,Wide Angle
PAP, GPS and Google Map
8 Visual PTZ
three visual PTZ
on Move, Random
Clicks to switch to one of the
control modes: Fixed Directi
Move or Center Move.
9 PTZ Home to the home position.Click to return the dome view
10 I/O Control Starts the I/O Control Panel.
11 PTZ Control and the Visual PTZ.Starts the PTZ Control Panel
12
Show
System
Menu
Brings up these functions: Alarm Notify,Video
and Audio Configuration, Remote Config, Show
Camera Name and Image Enhance.
For detail, see 3.1 The Live View Window, GV-IP Speed Dome GV-SD220
User’s Manual on the Software CD.
15