GeoVision GV-DSP LPR User manual

Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
User's Manual
GV-DSP LPR
LDSP23V204-A

© 2014 GeoVision, Inc. All rights reserved.
Under the copyright laws, this manual may not be copied, in whole or in part, without the
written consent of GeoVision.
Every effort has been made to ensure that the information in this manual is accurate.
GeoVision, Inc. makes no expressed or implied warranty of any kind and assumes no
responsibility for errors or omissions. No liability is assumed for incidental or consequential
damages arising from the use of the information or products contained herein. Features and
specifications are subject to change without notice.
GeoVision, Inc.
9F, No. 246, Sec. 1, Neihu Rd.,
Neihu District, Taipei, Taiwan
Tel: [phone]
Fax: [phone]
http://www.geovision.com.tw
Trademarks used in this manual: GeoVision, the GeoVision logo and GV series products are
trademarks of GeoVision, Inc. Windows and Windows XP are registered trademarks of
Microsoft Corporation.
October 2014

Preface
Welcome to the GV-DSP LPR User’s Manual.
The GV-DSP LPR has two models designed to meet different needs. Each model has its own
firmware that can only be used on the specific model. This Manual is designed for the
following models and firmware version:
Model Firmware Version
GV-DSP LPR V2 2.04
GV-DSP LPR V3 2.04
This Manual provides an overview of the GV-DSP LPR and its accessories. The instructions
will guide you through the installation and use of the GV-DSP LPR as well.
Note: Be sure to load the default settings after you update from firmware V.1.06 or earlier to
V2.0 or later.
i

Contents
Recognition Engine Version ...............................................................iv
Chapter 1 Introduction .......................................................................1
1.1 Key Features.......................................................................................................... 3
1.2 Packing List............................................................................................................ 4
1.3 System Requirements & Software Compatibility..................................................... 4
1.4 Options................................................................................................................... 4
1.5 Physical Description ............................................................................................... 5
1.5.1 Front View.................................................................................................. 5
1.5.2 Rear View .................................................................................................. 6
Chapter 2 Getting Started ..................................................................7
2.1 Installing on a Network ........................................................................................... 7
2.2 Assigning an IP Address......................................................................................... 8
2.3 Configuration Basics............................................................................................... 9
Chapter 3 Accessing the GV-DSP LPR ...........................................10
3.1 Accessing Your Surveillance Images and Recognition Results..............................10
3.2 Functions Featured on the Main Page...................................................................11
3.2.1 The Live View Window..............................................................................12
3.2.2 Adjustment of Video Attributes..................................................................13
3.2.3 Snapshot of a Live Video ..........................................................................14
3.2.4 Video Recording .......................................................................................14
3.2.5 Firmware Upgrade ....................................................................................15
3.2.6 Network Status .........................................................................................15
Chapter 4 Administrator Mode ........................................................16
4.1 Video and Motion ..................................................................................................18
4.1.1 Video Settings...........................................................................................18
4.1.2 Detection Mode.........................................................................................21
4.1.3 Recognition Engine Settings .....................................................................24
4.2 I/O Control.............................................................................................................29
4.2.1 Input Setting..............................................................................................29
4.2.2 Output Setting...........................................................................................30
ii

4.2.3 RS232 / GPS ............................................................................................31
4.3 Events & Alerts......................................................................................................33
4.3.1 LPR Remote Server..................................................................................33
4.3.2 VSM..........................................................................................................35
4.3.3 FTP...........................................................................................................36
4.3.4 Inquire Recognized Database...................................................................37
4.3.5 Registry Database ....................................................................................38
4.4 Recognizing Schedule Settings .............................................................................40
4.5 Network .................................................................................................................41
4.5.1 Status .......................................................................................................41
4.5.2 LAN...........................................................................................................42
4.5.3 UMTS .......................................................................................................44
4.5.4 Wireless....................................................................................................46
4.5.5 Advanced TCP/IP .....................................................................................47
4.5.6 IP Filter .....................................................................................................49
4.6 Management .........................................................................................................50
4.6.1 Date & Time Setting..................................................................................50
4.6.2 Storage Settings .......................................................................................52
4.6.3 User Account ............................................................................................53
4.6.4 Log Information.........................................................................................54
4.6.5 Tools.........................................................................................................55
Chapter 5 Advanced Applications................................................... 56
5.1 Upgrading System Firmware .................................................................................56
5.1.1 Upgrading Firmware over LAN..................................................................57
5.1.2 Upgrading Firmware by Using the Utility ...................................................57
5.2 Restoring to Factory Default Settings ....................................................................60
Chapter 6 The I/O Terminal Block.........................................................61
6.1 I/O Port..................................................................................................................61
6.2 Terminal Block.......................................................................................................63
Specifications......................................................................................64
Appendix .............................................................................................66
A. Supported Wireless LAN USB Adaptor........................................................66
B. Supported Mobile Broadband Device ..........................................................66
iii

iv
Recognition Engine Version
GV-DSP LPR V2 / V3 of firmware version 2.04 only supports the following versions of
recognition engines:
No. Country Engine Version No. Country Engine Version
1 Arabia ²23 Japan ²
2 Australia V4209 24 Malaysia V6009
3 Austria V6009 25 Mexico V4048
4 Belgium V6009 26 Netherlands V4038
5 Brazil V3118 27 New Zealand V6009
6 Bulgaria V6009 28 Norway V6009
7 Canada ²29 Poland V6018
8 Chile V3208 30 Portugal V6018
9 China V4213 31 Qatar V3122
10 Columbia V6009 32 Russia V6018
11 Croatia ²33 Serbia ²
12 Cyprus V6009 34 Slovenia ²
13 Czech V6009 35 South Africa V6010
14 France V6009 36 Spain V6018
15 Germany V6009 37 Taiwan V4558
16 Global V6018 38 Taiwan Moto V4021
17 Guernsey V6009 39 Thailand ²
18 Hong Kong V6009 40 Turkey ²
19 Hungary V6009 41 UAE ²
20 Ireland V6009 42 UK V6009
21 Israel V3000 43 USA V4209
22 Italy V4038
Note: Recognition engine for Qatar is only supported in GV-DSP LPR V2 / V3 of firmware
version 2.03 or later.

Introduction 1
Chapter 1 Introduction
The GV-DSP LPR is a Linux-based license plate recognition system built in a small box.
Integrating with a Web server, the GV-DSP LPR can host its own Web site and compare
captured license plates with the database downloaded from GV-AS Manager and open a gate
barrier when there is a match.
Figure 1-1
1

The GV-DSP LPR can also deliver live view images and recognized plate numbers, date and
time to the GV-System for security surveillance.
Figure 1-2
2

Introduction 1
1.1 Key Features
•Non-PC based solution for 1 port traffic or mobile license plate recognition
•Wide operating temperature range
•Web-based configuration for image, security settings and firmware upgrade
•Recognition triggered by video motion detection or sensor inputs
•Opening a gate barrier when a captured license plate matches the database
•Manageable by GV-AS Manager access control system
•Digital watermark
•Hardware watchdog
•IP address filtering
•WiFi
•UMTS
•GPS Tracking
•Recognition results, images and live videos compatible with other system through OCX
SDK
3

1.2 Packing List
1. Power Adaptor x 1
2. WallHookx1
3. Conical Anchor x 4
4. Screw x 4
5. I/O Cable with RJ-45 Connector x 1
6. GV-DSP LPR User’s Manual on Software CD
1.3 System Requirements & Software Compatibility
System Requirements
32-bit Windows XP / Vista / 7 / Server 2008
OS 64-bit Windows 7 / Server 2008
Browser Internet Explorer 7.x to 10.x
Software Compatibility
GV-DSP LPR Firmware Compatible GV-ASManager Version
GV-DSP LPR F/W V2.0 GV-ASManager V4.0 & V4.1
GV-DSP LPR F/W V2.01 GV-ASManager V4.1
GV-DSP LPR F/W V2.02 GV-ASManager V4.2
GV-DSP LPR F/W V2.03 GV-ASManager V4.2.1 & V4.2.2
GV-DSP LPR F/W V2.04 GV-ASManager V4.2.3
1.4 Options
GV-GPS Receiver
GV-GPS Receiver is a Global Position System receiver,
allowing you to perform vehicle tracking and location
verification functions.
GV-Relay V2 Working with this module, GV-DSP LPR can drive the
loads of relay outputs over 5 volts.
4

Introduction 1
1.5 Physical Description
This section identifies the various components of the GV-DSP LPR.
1.5.1 Front View
GV-DSP LPR V2 / V3
Figure 1-3
No. Name Function
1 Power LED Indicates the power is supplied.
2 Ready LED Indicates the unit is ready for connection.
3 Load Default Button It resets all configurations to their factory settings. See 5.3 Restoring
to Factory Default Settings.
4 USB Port Connects a UMTS modem. See 4.5.3 UMTS.
5 Video In Connects a camera.
6 TV-Out
Connects an external monitor to output live videos and recognition
results immediately. It is useful when you cannot access the
GV-DSP LPR through the network.
5

6
1.5.2 Rear View
GV-DSP LPR V2 / V3
2 431 6
GV-DSP LPR V3
2 431 5
GV-DSP LPR V2
Figure 1-4
No. Name Function
1 DC 12 In Connects the supplied power adaptor.
2 Ethernet Port Connects a 10/100 Ethernet network.
3 Terminal Block Connects RS-232 devices. See Chapter 6 The I/O Terminal
Block.
4 I/O Port
A port for digital inputs and relay outputs. Insert the supplied
I/O Cable with RJ-45 Connector to this port. See Chapter 6
The I/O Terminal Block.
Note: The Wiegand interface is NOT functional now.
5 Mini SD Card Slot
(only for GV-DSP LPR V2)
Inserts a Mini Secure Digital (SD) card. The Mini SD card is
used for storing recognition images and data.
6 Micro SD Card Slot
(only for GV-DSP LPR V3)
Inserts a Micro Secure Digital (SD) card. The Micro SD card
is used for storing recognition images and data.

Getting Started
2
Chapter 2 Getting Started
This section provides basic information to get the GV-DSP LPR working on the network.
2.1 Installing on a Network
These instructions describe the basic connections to install the GV-DSP LPR on the network.
Here we use the GV-DSP LPR V3 as the example to demonstrate the steps.
Figure 2-1
1. Connect the video output of your camera to the BNC video input.
2. Connect the hub or switch on the LAN to the unit’s 10/100 Mbps Ethernet port.
3. Connect the power supply to the power input.
4. Wait until both Power and Ready LEDs are on and then you can set the IP address for
the unit.
7

2.2 Assigning an IP Address
Designed for use on an Ethernet network, the GV-DSP LPR must be assigned an IP address
to make it accessible.
Note: The GV-DSP LPR has a default address of 192.168.0.230. The computer used to set
the IP address must be under the same IP and subnet sequence assigned to the unit.
1. Open your Web browser, and type the default IP address http://192.168.0.230/.
2. In both Login and Password fields, type the default value admin. Click Apply.
3. In the left menu, select Network and then LAN to begin the network settings.
Figure 2-2
4. Select Static IP address. Type IP Address, Subnet Mask, Router/Gateway, Primary
DNS and Secondary DNS in the Configure connection parameters section.
5. Click Apply. The GV-DSP LPR is accessible by entering the assigned IP address on
the Web browser.
8

Getting Started
9
2
Important:
•Dynamic IP Address, PPPoE and UMTS should only be enabled if you know
which IP address the GV-DSP LPR will get from the DHCP server or ISP.
Otherwise you must use the Dynamic DNS service to obtain a domain name
linked to the GV-DSP LPR’s changing IP address first.
For details on Dynamic IP Address and PPPoE settings, see 4.5.5 Advanced
TCP/IP.
•When the GV-DSP LPR is unable to obtain a dynamic IP address from the DHCP
server, the default static IP address 192.168.0.230 will be applied instead.
•If Dynamic IP Address, PPPoE or UMTS is enabled and you cannot access the
unit, you may have to reset it to the factory default and then perform the network
settings again.
To restore the factory settings, see the Default button in 1.5.1 Front View.
2.3 Configuration Basics
Once the camera is properly installed, these important features can be configured using the
browser-based configuration page and are discussed in the following sections in this manual:
•Date and time adjustment: see 4.6.1 Date & Time Setting.
•Login and privileged passwords: see 4.6.3 User Account.
•Network gateway: see 4.5 Network.
•Video attribute (Brightness, Contrast, Saturation and Hue): see 3.2.2 Adjustment of
Video Attributes.
•Video format, resolution and frame rate: see 4.1.1 Video Settings.

Chapter 3 Accessing the GV-DSP LPR
Two types of users are allowed to log in the GV-DSP LPR: Administrator and Guest. The
Administrator has unrestricted access to all system configurations, while the Guest has the
access to live view and network status only.
3.1 Accessing Your Surveillance Images and Recognition
Results
Once installed, your GV-DSP LPR is accessible on the network. Follow these steps to access
your surveillance images and recognition results:
1. Start the Internet Explorer browser.
2. Enter the IP address or domain name of the GV-DSP LPR in the Location/Address
field of your browser.
Figure 3-1
3. Enter a login name and password.
•The default login name and password for Administrator are admin.
•The default login name and password for Guest are guest.
4. A video image, similar to the example on Figure 3-2, is now displayed in your browser.
Note: To enable the updating of images in Internet Explorer, you must set your browser to
allow ActiveX Controls and perform a once-only installation of GeoVision’s ActiveX
component onto your computer.
10

Accessing the GV-DSP LPR
3
3.2 Functions Featured on the Main Page
This section introduces the features of the Live View window and Network Status on the main
page. The two features are accessible by both Administrator and Guest.
Main Page of Guest Mode
▼Video and Motion
►Live View
▼Network
►Status
Figure 3-2
11

3.2.1 The Live View Window
Figure 3-3
No. Name Function
1 Live View Displays live video.
2 Play Starts the connection and plays live video.
3 Stop Terminates the connection.
4 Remote Config Adjusts video attributes of the live video.
5 Snapshot Takes a snapshot of live video.
6 File Save Records the live video and saves in .avi format.
7 Firmware Upgrade Upgrades the firmware of GV-DSP LPR.
8 Captured Image Displays the captured image.
9 Number Display Displays the recognized plate number.
10 Record List Lists the dates and times of detection results.
12

Accessing the GV-DSP LPR
3
3.2.2 Adjustment of Video Attributes
To adjust video attributes of the live video, follow these steps:
1. Click the Remote Config button (No. 4, Figure 3-3).
2. Move the slide bars (Brightness, Contrast, Saturation and Hue) to adjust video
attributes. Only the Administrator is allowed to adjust the configurations.
Figure 3-4
13

3.2.3 Snapshot of a Live Video
To take a snapshot of a live video, follow these steps:
1. Click the Snapshot button (No. 5, Figure 3-3). The Snapshot window appears.
2. Click the Print button to print out the displayed image. Or click the Save button to save
the image to the local computer.
Figure 3-5
3.2.4 Video Recording
You can record live video for a certain period of time to your local computer.
1. Click the File Save button (No.6, Figure 3-3). The Save As dialog box appears.
Figure 3-6
2. Specify Save in, type the File name, and click the Save button to start recording.
3. To stop recording, click the Stop button (No.3, Figure 3-3).
14