geratech EGE-UHD2-642FS User manual

EGE-UHD2-642FS
6×2 HDMI 4K UHD Matrix with HDCP 2.2 and Fast Switching

EGE-UHD2-642FS
6×2 HDMI 4K UHD Matrix with HDCP 2.2 and Fast Switching

EGE-UHD2-642FS
6×2 HDMI 4K UHD Matrix with HDCP 2.2 and Fast Switching
DISCLAIMERS
The information in this manual has been carefully checked and is believed to be accurate.
Geratech assumes no responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Geratech assumes no responsibility for any inaccuracies that may be contained in
this document. Geratech also makes no commitment to update or to keep current the
information contained in this document.
Geratech reserves the right to make improvements to this document and/or product at any
time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval
system, or any of its part translated into any language or computer file, in any form or by
any means - electronic, mechanical, magnetic, optical, chemical, manual, or otherwise -
without express written permission and consent from Geratech.
© Copyright 2015 by Geratech.
All Rights Reserved.
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be trademarks of the
companies with which they are associated.

EGE-UHD2-642FS
6×2 HDMI 4K UHD Matrix with HDCP 2.2 and Fast Switching
EGE-UHD2-642FS
6×2 HDMI 4K UHD Matrix with HDCP 2.2 and Fast Switching
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack or install or operate this
equipment, and before connecting the power supply.
Please keep the following in mind as you unpack and install this equipment:
• Always follow basic safety precautions to reduce the risk of fire, electrical shock and
injury to persons.
• To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this
product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any openings or empty slots
in the unit, as you may damage parts inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any weight to be placed
upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or openings in the unit
housing that provide ventilation and allow for sufficient space for air to circulate around
the unit.
REVISION HISTORY
VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE
VR0 21/12/15 Preliminary Release

EGE-UHD2-642FS
6×2 HDMI 4K UHD Matrix with HDCP 2.2 and Fast Switching
CONTENTS
1. Introduction.........................................................................1
2. Applications ........................................................................1
3. Package Contents...............................................................1
4. System Requirements........................................................1
5. Features...............................................................................2
6. Operation Controls and Functions ...................................3
6.1 Front Panel.......................................................................3
6.2 Rear Panel .......................................................................4
6.3 Remote Control ................................................................5
6.4 IR Pin Definitions..............................................................6
6.5 OSD Menu .......................................................................6
6.6 RS-232 Protocols .......................................................... 12
6.7 Telnet and RS-232 Commands..................................... 12
6.8 Telnet Control ................................................................ 17
6.9 Web GUI Control........................................................... 19
7. Connection Diagram.........................................................22
8. Specifications ...................................................................23

1
1
EGE-UHD2-642FS
6×2 HDMI 4K UHD Matrix with HDCP 2.2 and Fast Switching
EGE-UHD2-642FS
6×2 HDMI 4K UHD Matrix with HDCP 2.2 and Fast Switching
1
1. INTRODUCTION
The 6 by 2 HDMI 4K UHD Matrix with HDCP 2.2 and Fast Switch which allows HDMI
signal from any of its 6 sources to be routed to and displayed on any of its 2 connected
HDMI displays simultaneously with View All Mode and Picture-in-picture (PIP) supported.
Fast switching technology can greatly eliminate the time required by swapping or turning
ON/OFF the connected displays. It supports 4Kx2K, 3D, 30-bit Deep Color, Hi-Def audio
and other features defined by HDMI specifications.
The management of source/sink scenarios can be operated easily through on-panel
buttons, IR remote control, RS-232 or Ethernet protocol.
2. APPLICATIONS
• Entertainment Room / Home Theater
• Show Room / Demo Room
• Lecture Room/Hall Presentation
• Show Room/Demo Room
• Public Commercial Display
• Information Board
3. PACKAGE CONTENTS
• 6 by 2 HDMI 4K UHD Matrix with HDCP2.2 and Fast Switching
• Remote Control with Battery
• Left & Right Rack Ears
• 5V/2.6A DC Power Adaptor
• IR Receiver Cable
• Operation Manual
4. SYSTEM REQUIREMENTS
Input source equipment such as Blu-ray/DVD/PS3 player or Set-Top-Box and output HDMI
TV/Display and or audio amplifier with connection cables.

2
2
EGE-UHD2-642FS
6×2 HDMI 4K UHD Matrix with HDCP 2.2 and Fast Switching
2
5. FEATURES
• HDMI with 3D & 4Kx2K supported, HDCP 2.2 and DVI compliant
• Supports 6 HDMI inputs and 2 HDMI outputs
• Displays any of 6 High-Definition sources on 2 HDTV displays simultaneously with fast
switch
• When in Preview mode, the system will be treated as Switcher (2 HDMI output same
images at the same time)
• In Preview mode, it support View All (1 Main video source and 5 Sub video sources) and
PIP (1 Main video source and 1 Sub video source). 3D and 4K2K sources inputs are not
supported
• Note: View All is TDM (Time Division Multiplexing display)
• 3DTV Pass-Through
• Supports HDTV resolutions up to 4Kx2K (3840x2160@24/25/30 & 4096x2160 @30Hz)
• Supports Optical audio extraction
• Supports Optical audio sampling rate output up to 192kHz
• Supports data rate from 300Mbps to 3Gbps and Deep Color up to 1080p 30-bit
• Supports individual EDID or common EDID
• Supports LPCM 2/5.1/7.1CH, Dolby Digital 2~5.1CH, DTS 2~5.1CH (Pass through),
Dolby TrueHD and DTS-HD Master Audio
• Supports 6 sets of Matrix preset functions for input/output setting
• Input port HDCP support Standard and Apple mode. The Apple mode selection to
guarantees the use of Apple devices
• Compliant with DVI source (Not supporting Deep color and Color space YCbCr 422/444)
• Supports OSD on output B under Preview Mode

3
3
EGE-UHD2-642FS
6×2 HDMI 4K UHD Matrix with HDCP 2.2 and Fast Switching
EGE-UHD2-642FS
6×2 HDMI 4K UHD Matrix with HDCP 2.2 and Fast Switching
3
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
1POWER & LED: PRESS THE POWER KEY TO TURN ON THE DEVICE AND THE
LED WILL ILLUMINATED.
2IR WINDOW: IR RECEIVER RECEIVES REMOTE CONTROL SIGNAL FROM THE
REMOTE CONTROL INCLUDED IN THE PACKAGE.
3OUTPUT A ~ B: PRESS THESE OUT BUTTONS ONCE ALONG WITH ONE IN
BUTTONS TO SELECT INPUT SOURCE FOR SELECT OUTPUT DISPLAY.
4IN 1~6: PRESS THESE IN BUTTONS TO SELECT AN INPUT FROM 6 INPUT
SOURCES.
5MUTE: PRESS TO MUTE AUDIO SOURCE.
6TAKE: PRESS THIS BUTTON TO CONFIRM IN AND OUT SELECTION.
7CANCEL: PRESS THIS BUTTON TO CANCEL IN AND OUT SELECTION.
8ENTER: PRESS THIS BUTTON TO CONFIRM SELECTION.
9MENU: PRESS TO ENTER MENU OPTIONS.
10 +/-: PRESS TO MOVE UP / DOWN UNDER MENU OPTIONS.
11 ALL: PRESS TO SELECT ALL OUTPUTS TO DISPLAY WITH ONE INPUT SOURCE.
12 PRESET: PRESS THIS BUTTON, THE OLED MENU WILL SHOW PRESET, THEN
SELECT IN 1~6, PRESS “TAKE” TO CONFIRM THE SELECTION OR PRESS
“CANCEL” TO DESELECT.
13 LOCK: PRESS TO LOCK ALL BUTTON FUNCTIONS ON THE PANEL, PRESS AND
HOLD 5 SECONDS TO RESCISSION LOCK MODE.
14 MODE: TAKE MODE / REAL TIME MODE SWITCH.
15 LCM: DISPLAY INPUT AND OUTPUT SELECTION AND MENU OPTIONS.
6X2 HDMI MATRIX FAST SWITCH
IN 1IN 2IN 3IN 4IN 5IN 6 MUTE
OUT A OUT B
POWER
TAKE
CANCEL
ENTER
MENU
PRESET
ALL
MODE
LOCK
+
-
1 2 4 5
3
6 7 8 10 14112 115
9 11 13

4
4
EGE-UHD2-642FS
6×2 HDMI 4K UHD Matrix with HDCP 2.2 and Fast Switching
4
6.2 Rear Panel
1HDMI IN: Connect from source equipment such as Blu-ray / DVD / PS3 player, Set-Top
Box or any HDMI equipped source device for input signal sending.
2HDMI OUT: Connect to HDMI TV / display or HD amplifier for output image and audio
or audio display.
3S/PDIF OUT: Connect to Audio sound system or Amplifier for digital output sound.
4SERVICE: This is reserved for firmware update use only.
5CONTROL: Connect to PC / Laptop with active internet service for Telnet / Web GUI
control with RJ-45 terminated cable.
6RS232: Connect to PC / Laptop to control the device.
7IR IN: Connect the IR receiver which contented in the package for receive IR signal
from the remote control.
8DC 5V: Connect the adapter with power cord which included in the package and
connect to AC wall outlet for power supply.
CONTROLSERVICE
HDMI IN HDMI OUT S/PDIF OUT
AB
123456AB RS232 IR IN DC 5V
1 2 3 4 5 6 7 8

5
5
EGE-UHD2-642FS
6×2 HDMI 4K UHD Matrix with HDCP 2.2 and Fast Switching
EGE-UHD2-642FS
6×2 HDMI 4K UHD Matrix with HDCP 2.2 and Fast Switching
5
6.3 REMOTE CONTROL
1POWER: PRESS POWER KEY TO TURN ON THE
DEVICE OR SET TO STANDBY MODE.
2OUT A~B: PRESS THESE OUT BUTTONS ONCE
THEN TO SELECT AN INPUT SOURCE FOR AN
OUTPUT DISPLAY.
3TAKE: PRESS THIS BUTTON TO CONFIRM IN AND
OUT SELECTION.
4MODE: PRESS TO SWITCH TO MATRIX OR
PREVIEW MODE.
MATRIX MODE: PRESS OUT A OR OUT B OR BOTH
THEN SELECT FROM INPUT 1~6 OR MUTE TO
SELECT INPUT SOURCES, PRESS TAKE AFTER
SELECTION TO CONFIRM OR PRESS CANCEL TO
UNDO.
PREVIEW MODE: SELECT VIEW ALL OR PIP MODE
BY ENTERING MENU PAGE.
SELECT TO VIEW ALL: PRESS FROM INPUT 1~6
OR MUTE TO SELECT INPUT SOURCES FOR MAIN
CHANNEL.
SELECT TO PIP MODE: PRESS FROM OUT A~B THEN PRESS FROM INPUT 1~6
OR MUTE TO SELECT INPUT AS MAIN OR SUB VIDEO SOURCES, PRESS ALL OR
SWAP TO SWITCH FROM MAIN OR SUB VIDEO SOURCES.
5PV DISP.: PRESS TO SWITCH PREVIEW DISPLAY ON AND OFF.
6SWAP: WHILE IN PIP MODE, PRESS TO SWAP MAIN OR SUB VIDEO SOURCE.
7MENU: PRESS TO ENTER MENU OPTIONS.
8ENTER: PRESS THIS BUTTON TO CONFIRM SELECTION.
9+/-: PRESS TO MOVE UP AND DOWN UNDER MENU OPTIONS.
10 ALL: PRESS TO SELECT ALL OUTPUTS TO DISPLAY WITH ONE INPUT SOURCE.
11 IN 1~6: PRESS THESE IN BUTTONS TO SELECT AN INPUT FROM 6 INPUT
SOURCES.
12 CANCEL: PRESS THIS BUTTON TO CANCEL IN AND OUT SELECTION.
13 PRESET: PRESS THIS BUTTON, THE OLED MENU WILL SHOW PRESET, THEN
SELECT IN 1~6, PRESS “TAKE” TO CONFIRM THE SELECTION OR PRESS
“CANCEL” TO DESELECT.
IN 3
IN 5
MUTEENTER -
OUT A
OUT B
MODE
PV DISP. PRESET IN 4
SWAP LOCK
ALLIN 1
TAKE IN 2
CANCEL
+MENU IN 6
CR-136
1
15
12
2
3
4
5
6
7
8
9
13
10
14
11

6
6
EGE-UHD2-642FS
6×2 HDMI 4K UHD Matrix with HDCP 2.2 and Fast Switching
6
14 LOCK: Press to lock all button functions, press and hold 5 seconds to rescission lock mode.
15 MUTE: Press to mute audio source.
6.4 IR Pin Definitions
6.5 OSD Menu
3
1
2
IR Receiver
IR Signal
Power
Grounding
Main Menu Sub Menu Description Default
EDID Mode All All Input ports are
using same EDID.
In menu “EDID All”,
can select suitable
EDID.
All
Appoint Each Input port can
select individual
EDID.
In menu “EDID
IN1~6” select
suitable EDID.
Exit
EDID All Sink A Copy Output A
display
EDID
8/2D/PCM/1080
Sink B Copy Output B
display
EDID
8/2D/PCM/720P Standard EDID.
Content: deep
color/2D3D/audio/
native resolution.

7
7
EGE-UHD2-642FS
6×2 HDMI 4K UHD Matrix with HDCP 2.2 and Fast Switching
EGE-UHD2-642FS
6×2 HDMI 4K UHD Matrix with HDCP 2.2 and Fast Switching
7
Main Menu Sub Menu Description Default
8/2D/PCM/
AC3/720P
Standard EDID.
Content: deep
color/2D3D/audio/
native resolution.
8/2D/PCM/1080P Standard EDID.
Content: deep
color/2D3D/audio/
native resolution.
8/2D/PCM/
AC3/1080P
Standard EDID.
Content: deep
color/2D3D/audio/
native resolution.
8/2D/PCM/4K2K Standard EDID.
Content: deep
color/2D3D/audio/
native resolution.
8/2D/PCM/
AC3/4K2K
Standard EDID.
Content: deep
color/2D3D/audio/
native resolution.
8/2D/PCM/Y420 Standard EDID.
Content: deep
color/2D3D/audio/
native resolution.
8/2D/PCM/AC3/
Y420
Standard EDID.
Content: deep
color/2D3D/audio/
native resolution.
Exit
EDID IN1 Same as EDID All. Select Input 1 EDID. Same as
EDID All.
EDID IN2 Same as EDID All. Select Input 2 EDID. Same as
EDID All.

8
8
EGE-UHD2-642FS
6×2 HDMI 4K UHD Matrix with HDCP 2.2 and Fast Switching
8
Main Manu Sub Menu Description Default
EDID IN3 Same as EDID All. Select Input 3 EDID. Same as EDID All.
EDID IN4 Same as EDID All. Select Input 4 EDID. Same as EDID All.
EDID IN5 Same as EDID All. Select Input 5 EDID. Same as EDID All.
EDID IN6 Same as EDID All. Select Input 6 EDID. Same as EDID All.
Matrix Preset Preset 1 IN/OUT default No.1. A=1, B=2
Preset 2 IN/OUT default No.2. A=1, B=2
Preset 3 IN/OUT default No.3. A=1, B=2
Preset 4 IN/OUT default No.4. A=1, B=2
Preset 5 IN/OUT default No.5. A=1, B=2
Preset 6 IN/OUT default No.6. A=1, B=2
Exit
HDCP Input IN1 Standard/ Apple Set IN1 in Standard/
Apple mode.
Standard
IN2 Standard/ Apple Set IN2 in Standard/
Apple mode.
Standard
IN3 Standard/ Apple Set IN3 in Standard/
Apple mode.
Standard
IN4 Standard/ Apple Set IN4 in Standard/
Apple mode.
Standard
IN5 Standard/ Apple Set IN5 in Standard/
Apple mode.
Standard
IN6 Standard/ Apple Set IN6 in Standard/
Apple mode.
Standard
Exit

9
9
EGE-UHD2-642FS
6×2 HDMI 4K UHD Matrix with HDCP 2.2 and Fast Switching
EGE-UHD2-642FS
6×2 HDMI 4K UHD Matrix with HDCP 2.2 and Fast Switching
9
Main Menu Sub Menu Description Default
Preview Mode View All 1 Main video source and 5
Sub video sources.
View All
PIP 1 Main video source and 1
Sub video source.
Exit
Preview Position View
All
Top Preview 5 Sub screens
position.
Top Left
Right Preview 5 Sub screens
position.
Bottom Preview 5 Sub screens
position.
Left Preview 5 Sub screens
position.
PIP Top Left Preview sub screen position.
Top Right Preview sub screen position.
Bottom
Right
Preview sub screen position.
Bottom
Left
Preview sub screen position.
Exit
OSD
Transparency
0~15 Preview OSD background
transparency.
6
Exit
OSD Timeout OSD Off Preview without OSD info OSD Always
On

10
10
EGE-UHD2-642FS
6×2 HDMI 4K UHD Matrix with HDCP 2.2 and Fast Switching
10
Main Manu Sub Menu Description Default
5~20 Preview with OSD
info show 5~20
Seconds then
disappear
OSD Always On Preview with OSD
always on
Exit
Network Setup IP Mode DHCP, Static DHCP
IP Setup Static IP.
Mask Setup Static Mask.
Gate Setup Static
Gateway
Do Re-Link Re-Link After Setup
Network, the System
need to re-link.
Exit
Network Status Link Network Status
DHCP, Static or Not
Linked.
IP Get IP
Mask Get Netmask
Gate Get Gateway
MAC System MAC
Exit
Source Detection IN1 On/Off,
IN2 On/Off, Detect IN1, IN2
source with/without
signal.
IN3 On/Off,
IN4 On/Off, Detect IN3, IN4
source with/without
signal.

11
11
EGE-UHD2-642FS
6×2 HDMI 4K UHD Matrix with HDCP 2.2 and Fast Switching
EGE-UHD2-642FS
6×2 HDMI 4K UHD Matrix with HDCP 2.2 and Fast Switching
11
Main Menu Sub Menu Description Default
IN5 On/Off
IN6 On/Off Detect IN5, IN6
source with/without
signal.
Exit
Sink A Info Type, Manuf. Detect and analysis
Output A display’s
EDID.
Content: Type(HDMI/
DIV/VGA),
Manufactory/Model
number.
Native Content: Native
resolution.
Video Format Content: deep color,
2D/3D, 4K2K.
Video Format Content: PCM,
Bitstream, HBR.
Exit
Sink B Info Same as Sink A Info. Detect and analysis
Output B display’s
EDID.
Firmware FW Version Display Model
number & FW
Version.
Update FW Update.
Exit
Factory Reset Do Reset Do System Reset.
Exit
Exit

12
12
EGE-UHD2-642FS
6×2 HDMI 4K UHD Matrix with HDCP 2.2 and Fast Switching
12
Matrix
PIN Definition
1 NC
2 Tx
3 Rx
4 NC
5 GND
6 NC
7 NC
8 NC
9 NC
Baud Rate: 115200bps
Data bit: 8 bits
Parity: None
Flow Control: None
Stop Bit: 1
6.7 Telnet and RS-232 Commands
Command Name Description Description of Parameter
P0 Power Off (Standby) NONE
P1 Power On NONE
IPCONFIG Display The Current
IP Congure
NONE
SIPADDR X.X.X.X Set Ethernet IP
Address
X=0~255
SNETMASK X.X.X.X Set Ethernet Net
Mask
X=0~255
SGATEWAY X.X.X.X Set Ethernet
Gateway
X=0~255
6.6 RS-232 Protocols
Remote Control
PIN Definition
1 NC
2 Rx
3 Tx
4 NC
5 GND
6 NC
7 NC
8 NC
9 NC

13
13
EGE-UHD2-642FS
6×2 HDMI 4K UHD Matrix with HDCP 2.2 and Fast Switching
EGE-UHD2-642FS
6×2 HDMI 4K UHD Matrix with HDCP 2.2 and Fast Switching
13
Command Name Description Description of Parameter
HTTPPORT N1 Set Http Port Number N1=0~65535
TELNETPORT N1 Set Telnet port number N1=0~65535
RSTIP IP Configuration Set To
<DHCP>
NONE
A N1 Set Output A Source to
input N1
N1=1~6
B N1 Set Output B Source to
input N1
N1=1~6
I N1 Set All Outputs Source
to input N1
N1=1~6
EDIDMODE Show EDID Mode NONE
EDIDMODE N1 Set EDID Mode N1=0(Appoint), 1(All)
EDIDALL Show EDID Mode
Source for All
NONE
EDIDALL N1 Set EDID Mode Source
for All
N1=0(Sink A), 1(Sink B),
2(8/2D/PCM/720p), 3(8/2D/
PCM/AC3/720p), 4(8/2D/
PCM/1080p), 5(8/2D/
PCM/AC3/1080p), 6(8/2D/
PCM/4K2K), 7(8/2D/PCM/
AC3/4K2K), 8(8/2D/PCM/Y420),
9(8/2D/PCM/AC3/
Y420)
EDIDIN Show Input EDID Source NONE
EDIDIN N1 Show Input N1 EDID
Source
N1=1~6
6.7 RS-232 & Telnet Commands

14
14
EGE-UHD2-642FS
6×2 HDMI 4K UHD Matrix with HDCP 2.2 and Fast Switching
14
Command Name Description Description of Parameter
EDIDIN N1 N2 Set Input N1 EDID
Source
N1=1~6
N2=0(Sink A), 1(Sink B),
2(8/2D/PCM/720p), 3(8/2D/
PCM/AC3/720p), 4(8/2D/
PCM/1080p), 5(8/2D/
PCM/AC3/1080p), 6(8/2D/
PCM/4K2K), 7(8/2D/PCM/
AC3/4K2K), 8(8/2D/PCM/
Y420), 9(8/2D/PCM/AC3/
Y420)
HDCPIN Show All Input HDCP
Status
NONE
HDCPIN N1 Show All Input HDCP
Status
N1=1~6
HDCPIN N1 N2 Set Input N1 HDCP ON/
OFF
N1=1~6
N2=0(OFF), 1(ON)
PRESET Show All Preset
Configure
NONE
PRESET N1 Set Preset N1 Source to
Outputs
N1=1~6
PRESET N1 N2 Set Preset N1 Configure
N2
N1=1~6
N2=AXBX (X=1~6)
PVMODE Show preview mode NONE
PVMODE N1 Set preview mode to N1 N1=0(View all), 1(PIP)
PVPOS Show preview mode
position
NONE

15
15
EGE-UHD2-642FS
6×2 HDMI 4K UHD Matrix with HDCP 2.2 and Fast Switching
EGE-UHD2-642FS
6×2 HDMI 4K UHD Matrix with HDCP 2.2 and Fast Switching
15
Command Name Description Description of Parameter
PVPOS N1 Set preview mode to N1 In view all mode:
N1=0(Top), 1(Right),
2(Bottom), 3(Left)
In PIP mode:
N1=0(Top), 1(Top right),
2(Bottom Right), 3(Bottom
Left)
PVSRC Show preview mode source
select
None
PVSRC N1 In VIEWALL mode:
Set Main Screen Source To
Input N1 In PIP mode:
Show N1 screen source
select
In VIEWALL mode:
N1=1~6
In PIP mode:
N1=0(Main), 1(Sub)
PVSRC N1 N2 Set PIP mode main/sub
screen source to input N2
N1=0(Main), 1(Sub)
N2=1~6
OSDTRANS Show OSD transparency NONE
OSDTRANS N1 Set OSD transparency N1=0~15
OSDTO Show OSD time out NONE
OSDTO N1 Set OSD time out N1=0(OSD off), 1~16(5~20),
17(OSD always on)
SOURCEDET Show All Input Signal NONE
SOURCEDET N1 Show Input N1 Signal N1=1~6
SINKINFO SINKINFO NONE