German pool GPNB Series User manual

Please read these instructions and warranty information carefully
before use and keep them handy for future reference.
Online Warranty Registration
GPNB-5E
GPNB Series
Shower Unit Electric Water Heater
USER MANUAL

目錄 Table of Contents
產品特點 Features 04
產品結構 Product Structure 05
配件裝置選擇 Component Options 06
安裝說明 Installation Instructions 07
電路圖 Wiring Diagram 08
使用說明 Operating Instructions 09
產品規格 Specications 10
專用節水花灑 Water Saving Shower Head 10
保用條款 Warranty Terms & Conditions 11
請即進行保用登記﹗
有關保用條款細則，請看本說明書最後一頁。
Please register your warranty information now!
For Warranty Terms & Conditions,
please refer to the last page of this user manual.

P.4 P.5
產品特點 Features 產品結構 Product Structure
GPN及GPNB電熱水器配備原廠低壓式混合水龍
頭及花灑配件，適合於單點使用。
GPN and GPNB are a non-pressure water heaters
designed for single-point application.
若用戶需要安裝任何非隨機配件，必須先與
本公司認可之技術人員聯絡，否則本公司將
有權拒絕提供任何保養服務。
警告
! !
Each unit is equipped with a standard open-outlet
mixer and a shower set. Please install water heat-
er in accordance to the instructions stated on this
booklet. German Pool will NOT provide warranty
service on any product installed with unauthorized
components or devices.
Warning
不銹鋼內膽
Stainless Steel Inner Tank
採用長期耐高溫及受高壓容器專用之日本特殊不銹鋼製造，內膽結構堅
固，保證防銹、耐壓及不受水質侵蝕。
Constructed of Japanese heavy gauge stainless steel, specially made for
high temperature and pressure applications. It is durable and free of rust,
corrosion, deformity and hassle.
保溫設計
Thermal Insulation
完密噴注式保溫層，使用先進合成樹脂纖維材料，保持熱水溫度，同 時將
失溫程度減至最低，大大節省電能。
Optimal heat insulation is achieved by injected polyurethane foam.
發熱管
Heating Element
高質發熱管，發揮最高導熱效能，並內置超溫斷路器，確保安全。
High quality heating element with built-in thermal cut-out ensures
maximum thermal efficiency and safety.
溫度調節器
Thermostat
溫度調節器自動恒溫，保持水溫在預調溫度，節省能源，並配合個人 使用
熱水的習慣。
Thermostat provides automatic temperature control at preset
temperature to accommodate individual bathing habits and save energy.
額定壓力
Rated Pressure
0 MPa
最大來水壓力
Max Inlet Water Pressure
0.6MPa
防水等級
Water Resistance
IPX4
外殼
Exterior Casing
採用堅固防侵蝕金屬片，原裝多層焗油。
Constructed of corrosion-proof metal with multi-layer finishing.
符合規格
Conformity
機電工程署電氣產品(安全)規例。
Electrical Products (Safety) Regulations, Hong Kong.
認證標準
Certifications
IEC 60335-2-21
IEC 60335-1
能源標籤 Energy Label 1級能源標籤
Grade 1
能源標籤參考編號及年份
Energy Label Reference No. / Year
E190250 / 2019 (GPNB-5E)
1. 發熱線
2. 排水位
3. 出水位（熱）
4. 入水位（冷）
5. 恆溫器
6. 混合水制
7. 溫度表
1. Heating Element (Inside)
2. Drain
3. Outlet (Hot)
4. Inlet (Cold)
5. Thermostat
6. Lever Mixer
7. Thermometer
2
5
1
3 4
7
23 4
24
3
6

P.6 P.7
由電箱獨立伸延一條適合之電線(見下表)至浴室
門外接駁獨立開關掣，再將電線伸延至熱水器穿
進灰色線夾接到電線排上分別接上水線(N)，火
線(L)，及地線( )等。
Pre-Installation Notice
Installation should be done by a licensed technician
using the suppliedparts. German Pool is not
responsible for any defect or damage caused by
incorrect orunauthorized installation.
Positioning
Position water heater near water tap / point of use in
order to minimize heat loss. For wall-mount style,
appropriate anchor screws must be used and wall
should be strong enough to withstand the weight of
water heater. Keep a minimal distance between wall
and water heater.
Connecting Inlet and Outlet Pipes
The diameter of piping is ½” BSP. Make sure there is
no leaking at the joints. Turn on hot water tap to fill up
the inner tank until water flows from the shower head.
Turn off hot water.
Electric Wiring
This water heater must be earthed at
all time.
Use an independent wire (refer to table below) leading
from the meter box and connect it to an independent
on/off switch outside bathroom. Extend the wire through
the grey wire grip on the water heater. Dismount the
bottom plate and wire up Neutral (N), Life (L) and
Earth ( ) terminals.
安裝前注意
安裝必須使用原廠配件。若不按指示方法安
裝及使用而引致任何損壞，本公司概不負責。
安裝工作應由專業持牌水電技術人員負責。
掛牆定位
先將熱水器背板以膨脹螺絲安裝於承重的牆壁上，
然後將熱水器背部凹孔扣在背板上，並調整至緊
貼牆壁及保持垂直為佳。花灑頭插座以膨脹螺絲
安裝於適當位置上。
水喉接駁
水喉管件直徑為½”英吋，接駁妥當後應試看接
駁位置有否漏水，妥當後即可將有紅點之熱水掣
打開注水，直至花灑頭噴水即表示內膽經已注滿，
並可將熱水掣關好。
接電方法
本熱水器必須永久可靠地連接地線。
安裝說明 Installation Instructions
P.7
本熱水器必須永久可靠地連接至水管，
且不能使用軟管連接。
Appliance intended to be permanently
connected to the water mains and not
connected by a hose-set.
!
! 特別注意 ! Attention
配件裝置選擇 Component Options
B
B
GPNB
內置單控式混合龍頭
Built-in Single Lever Mixer
溫度顯示器
Thermometer
插座式花灑頭
Plug-In Type Shower Head
B :
S :
D :
標準配件裝置
Standard Components
內置單控式混合龍頭
Built-in Single Lever Mixer
溫度顯示器
Thermometer
插座式花灑頭
Plug-In Type Shower Head
B :
S :
D :
標準配件裝置
Standard Components
P.6
配件裝置選擇 Component Options

P.8 P.9
電源開關掣
設於熱水器外用以切斷電源供應之開關掣，應全
極切斷電源，兩極之間應保持最少3mm距離。
於浴室內安裝本電熱水器時必須遵照IEE之有關
電線安裝條例規格接駁。電源開關應採用有顯示
燈類型，當用戶需要作任何內膽清洗或維修，必
先切斷電源。
測試使用
水喉與電源接駁妥當及內膽注滿水後，便可進
行通電。此時指示燈會亮著，用戶便可將自動
恆溫旋鈕調校至最高度數。當溫度達到75℃
時，恆溫器即會自動停止加熱。選擇適當溫度
後不應以恆溫旋鈕當作開關掣使用，因此舉會
縮減該配件之使用壽命。
Power Switch
The external switch is used to completely disconnect
water heater from power supply. It should disconnect
all poles, and a contact separation of at least 3 mm
must be present.
IEE wiring regulations should be observed when the
water heater is installed in the bathroom.
Testing
Oncethe piping and wiring are connected and
inner tank has been filled up with water, switch
on the power. The indicator lightwill be lit. Turn
control knob to the desired temperature (Max.
temperature is 75°C). Do not use the control
knob as an on/off switch.
安裝說明 Installation Instructions
P.8
發熱線功率 (千瓦)
Heating Element Rating (kW)
所需電源(安培)
Electric Current (A)
電源線最低要求(平方毫米)
Wiring (mm²)
2 kW 10 A (單相1PE) 2.5 mm²
3 kW 15 A (單相1PE) 2.5 mm²
4 kW 20 A (單相1PE) 4.0 mm²
GPNB
220 伏特 A.C. -單相
220 Volt A.C. - Single Phase
GPN
GPNB
P.11
電路圖 Wiring Diagram
恒溫器及斷路裝置
Thermostat & Cutout
發熱元件
Heating Element
指示燈
Indicator
2
1
L
N
B
A
指示燈
Indicator
發熱元件
Heating Element
恒溫器及斷路裝置
Thermostat & Cutout
NL
A
B
1 2
停水期間
停水時不應將熱水器內之存水用盡，否則會導
致發熱線損壞。恢復供水後，應先扭開熱水掣
直至有水從花灑流出。待內膽注滿水後，用戶
便可重新開啟電源。
水質問題
若來水水源為河水、井水、地下水或礦物質含
量較高，用戶必需經常定期清洗發熱線以確保
發熱線正常運作及發揮最佳製熱效能。
花灑頭滴水
因冷縮熱脹原理，熱水器內膽當達到高溫時便
會有少量水在花灑頭流出。
出水位
出水位乃本熱水器之排氣管，除德國寶指定之
花灑配件外，不得接駁任何其他水喉配件或
裝置。
Water Shortage
During water shortage, do not drain water from
inner tank. The heating element would be damaged
if it is not submerged under water. When water
supply resumes, turn on hot water tap and let water
flows through the shower head before switching on
the power.
Source of Water Supply
If the water source is a river, a well, underground
water or has relatively high mineral content, user
must clean the heating element regularly to ensure
it will operate at optimum thermal efficiency.
Dripping
Due to thermal expansion, small amount of water
may drip off from the shower head when the inner
tank temperature is very high.
Outlet
The outlet of the water heater is supposed to act
as a vent and should not be connected to any
unauthorized piping attachment or device.
使用說明 Operating Instructions
警告
1. 必須嚴密看管兒童，防止他們接觸及把玩
熱水器，以免燙傷、觸電或受傷。
4. 若設置溫度超過50°C，會有燙傷危險，
所以必須混合冷水後才使用。
3. 電源進線段應加裝漏電保護裝置，漏電保
護裝置的額定動作電流應不大於30mA。
2. 本產品不適用於缺少了身體、感覺或精神
能力，或缺乏經驗和知識的人（包括兒
童）使用，除非他們在一個了解本產品使
用的人監督指導下使用，並對他們的安全
負責任。
Warning
1. Do not allow children to touch or play with the
water heater. Supervision is required during
use, in order to prevent the danger of a scald,
electrical shock or any other injuries.
4. If the temperature is set above 50˚C, cold
water must be mixed in to prevent the danger
of a scald.
3. An electric-leakage protection device must be
installed to the power inlet. The electric current
of this protection device should be below
30mA.
2. This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they have
been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
! !
P.12

P.10
產品規格 Specifications
64mm
25.4mm
14.2mm
229mm
電壓
Voltage
功率
Power
尺寸
Dimension
(MM)
容量
Capacity
淨重
Net
Weight
防水等級
Water
Resistance
額定壓力
Rated
Pressure
最大來水壓力
Max. Inlet
Water
Pressure
GPNB-5E 220V 3kW (H) 595
(W) 330
(D) 250
18 L 11.7kg IPX4 0 MPa 0.6 MPa
* 正常情況下，如供水系統之來水水壓超過 0.6 MPa，用戶必須額外加裝減壓器將水壓調低。
如來水壓力超過 0.6 MPa 而用戶未有安裝減壓器，本公司有權拒絕為熱水器進行任何維修。
產品規格及設計如有變更，恕不另行通知。中英文版本如有出入，
一概以中文版為準。最新版本以 www.germanpool.com 網上版為準。
*Under normal working conditions, incoming pressure should not exceed 0.6 MPa. Otherwise, a separate
pressurecontrol device is necessary. When incoming water pressure exceeds 0.6 MPa, German Pool will not
provide anyrepair service until a pressure control device is installed.
If there is any inconsitency or ambiguity between the English version and
Chinese version, the Chnese version shall prevail.
Refer to www.germanpool.com for the most up-to-date version.
保用條款
此保用提供德國寶產品之機件在正常使用下壹年保用
(自購買日起計算)。
Warranty Terms & Conditions
Under normal operations, the product will gurantee a 1-year full
warranty provided by German Pool (effective from the date of
purchase).
1. Customer who fails to present original purchase invoice will
not beeligible for free warranty service.
2. Customer should always follow the operating
instructions. Thiswarrantydoes not apply to:
- labour costs for on-site installation, check-up, repair,
replacement of parts and other transportation costs;
- damages caused by accidents of any kind (including
material transfer and others);
- operating failures resulting from applying incorrect voltage,
improperusage, and unauthorized installations
or repairs.
3. Thiswarranty is invalid if:
- the purchase invoice is modified by an unauthorized party;
- the product is used for anycommercial or industrial purposes;
- the product is repaired or modifiedby unauthorized
personnel, orunauthorizedparts are installed;
- the serial number is modified, damagedor removed from
the product.
4. German Poolwill, at its discretion, repair or replace any
defective part.
5. Thiswarranty will be void if there is any transfer of
ownership from the original purchaser.
1. 未能出示購買發票正本者，將不獲免費維修服務。
2. 用戶應依照說明書的指示操作。本保用並不包括﹕
- 上門安裝、檢驗、維修或更換零件之人工以及
一切運輸費用﹔
- 因天然與人為意外造成的損壞 (包括運輸及其他)﹔
- 電源接合不當、不依說明書而錯誤或疏忽使用本
機所引致之損壞。
3. 於下列情況下，用戶之保用資格將被取消﹕
- 購買發票有任何非認可之刪改；
- 產品被用作商業或工業用途；
- 產品經非認可之技術人員改裝或加裝任何配件；
- 機身編號被擅自塗改、破壞或刪除。
4. 總代理有權選擇維修或更換配件或其損壞部份。
5. 產品一經被轉讓，其保用即被視作無效。
機身號碼 Serial No. :
購買商號 Purchased From :
發票號碼 Invoice No. :
購買日期 Purchase Date :
型號 Model No. :
另請填妥以下表格並與正本發票一併保存，以便維修時核對資料。用戶提供之所有資料必須正確無誤，否則免費保用將會無效。
Pleasefill out the form below. This information and the original purchaseinvoice will be required for anyrepairs. Warranty will be
invalidated if information provided is found to be inaccurate.
此保用只適用於香港及澳門 This warranty is valid only in Hong Kong and Macau
GPNB-5E
客戶服務及維修中心 Customer Service & Repair Centre
Hong Kong
10/F, Kowloon Godown
1-3 Kai Hing Road, Kowloon Bay,
Kowloon, Hong Kong
Tel : [phone]
Fax : [phone]
Email : [e-mail]
Macau
3/F, Edificio Industrial Pou Fung,
145 Rua de Francisco Xavier Pereira,
Macau
Tel : [phone]
Fax : [phone]
香港
九龍灣啟興道1-3號
九龍貨倉10樓
電話：[phone]
傳真：[phone]
電郵：[e-mail]
澳門
澳門俾利喇街145號
寶豐工業大廈3樓
電話：[phone]
傳真：[phone]
*
貴戶須在購機十天內，以下列其中一種方式向本公司
登記資料，保用手續方正式生效﹕
1)
填妥本公司網頁內之
保用登記表格
www.germanpool.com/
warranty
2)
填妥保用登記卡，
郵寄至本公司。
* This warranty is not valid until customer registration information
is receivedby ourService Centre within10 days ofpurchase
via one of the following means:
1) Visit our website and register
online:
www.germanpool.com/
warranty
2)
Complete all the fields on the
attached Warranty Card and
mail itback to our Customer
Service Centre.
創新空氣加壓技術
Air Jet Compression Technology
打開氣孔加入空氣，保持節水效果
同時增強水勢。
Air is drawn through the air hole to
increase water pressure.
本電熱水器必須使用德國寶專用慳水節能花灑頭。
The GPU Series can model must use our Water &
Energy Saving Aerated Showerhead as a necessary
accessory.
開關氣孔
Air Hole
專用節水花灑 Water Saving Shower Head

GPN/GPNB-M-18(9)
GPNB-5E-M-19(1)
G e rman Pool (Hong Kong) Limi t e d
www.germanpool.com
Hong Kong
Room 113, Newport Centre Phase II, 116 Ma Tau
Kok Road, Tokwawan, Kowloon, Hong Kong
Tel: [phone]
Fax:[phone]
China
Tel:[phone]
Fax:[phone]
8th, Xinxiang Road, Wusha Industrial Park,
Daliang, Shunde, Foshan, Guangdong
3/F, Edificio Industrial Pou Fung,
145 Rua de Francisco Xavier Pereira, Macau
Tel:[phone]
Fax:[phone]
Macau
©All rights reserved. Copying, reproducing or using the contents of this manual is not allowed without prior authorization from German Pool, violators will be prosecuted.
HONG KONG TOP BRAND TEN YEAR
ACHIEVEMENT AWARD