German pool crx9 User manual

Instantaneous Water Heater
即熱式電熱水器即热式电热水器
CRX9
在使用之前請詳細閱讀「使用說明書」及「保用條例」
，並妥為保存。
在使用之前請詳細閱讀 「使用說明書」及「保用條例」
，並妥為保存。
Please read these instructions and warranty information carefully
before use and keep them handy for future reference.
使用說明書
WH-CRX-M-10(2)
Printed in Germany WH-CRX-M-11(3)

1. Overview
1
7
2
3
4
5
6
When ordering spare parts, please always specify the appliance model, nominal rating and serial number!
Pos. Description
1 Brass connection set with back flow
prevention in hot water outlet
2 Heating element
3 Display panel
4 Safety thermal cut out
Pos. Description
5 Electronic board
6 Flow sensor
7 Cable seal
not shown: set of small spareparts
Layout of appliance
2
CRX9

CRX9
2. Table of contents
1. Overview .......................................................................................................................................................................2
2. Table of contents ...........................................................................................................................................................3
3. Technical specifications .................................................................................................................................................3
4. Operating instructions ...............................................................................................................................................4–6
5. Customer service ..........................................................................................................................................................7
6. Installation ..............................................................................................................................................................8–13
Warranty Terms and Conditions ......................................................................................................................................38
Customer Service Center .................................................................................................................................................39
3. Technical specifications
Type CRX 9
Capacity 0.2 l
Pressure-type, rating pressure 0.6 MPa (6bar)
Heating system Tubular heater
Nominal rating 8.0– 9.6kW
Rated voltage (50Hz) 1N/PE ~
Rated current at 220–240V 36–40A
Min. required conductor cross-section 3 × 6.0mm2
Factory preset flow reducer 5.0 l/min
Increase of temperature ∆t at present flow 23K
Hot water temperature at 20°C inlet temp. 43°C
Switch-on flow rate 2 l/min
Temperature presetting 35–55 °C
Useful for cold water up to 30°C
Water connection ½“ B.S.P. surface-mounted or flush-mounted
Net weight and dimensions (H × W × D) 2.2kg / 33 × 21 × 9cm
Protection class and type of protection to VDE 1 / IP25
Safety mark see type plate
3
GEFAHR
Operating Instructions:
Please read these instructions carefully before using the appliance!
中文使用說明書從第 14 頁開始 – Traditional Chinese manual starts on page 14
中文使用說明書從第 26頁開始 – Simplified Chinese manual starts on page 26

CRX9
4. Operation instructions
Safety instructions for closed-outlet water heaters:
• Installation, initial operation and maintenance of this appliance must only be conducted by an authorised profes-
sional, who will then be responsible for adherence to applicable standards and installation regulations.We assume
no liability for any damages caused by failure to observe these instructions.
• Do not use the appliance until it has been correctly installed and unless it is in perfect working order.
• The appliance is only suitable for domestic use and similar applications inside closed, frost-free rooms, and must only
be used to heat incoming water from mains supply.
• The appliance must never be exposed to frost.
• The appliance must be earthed at all times.
• The maximum water pressure must not exceed the value on the label.
• Before commissioning for the first time and each time the appliance is emptied (e.g. due to work on the plumbing
system, if there is a risk of freezing or in case of maintenance), the appliance must be vented correctly in accordance
with the instructions in this manual.
• Do not remove the front cover under any circumstances before switching off the mains electrical supply to the unit.
• Never make technical modifications, either to the appliance itself or the electrical leads and water pipes.
• Pay attention to the fact that water temperatures in excess of approx. 43 °C are perceived as hot, especially by chil-
dren, and may cause a feeling of burning. Please note that the fittings and taps may be very hot when the appliance
has been in use for some time.
• Water inlet temperature must not exceed 30°C.
• In case of malfunction, disconnect the fuses immediately. In case of leaks, cut off the cold water supply instantly.
Repairs must only be carried out by the customer service department or an authorised professional.
• This appliance must not be used by any person (including children) with limited physical, sensorial or mental abilities
or failing experience and/or knowledge unless they are supervised by a person responsible for their safety or received
instructions about how to use the appliance.Children should be supervised in order to make sure that they do not
play with the appliance.
GEFAHR
1 2
4
5
3
–
+
Description of appliance
The appliance is a closed-outlet electronically controlled instantaneous heater for
decentral water heating at one or two taps situated in close proximity to one another,
e.g. wash basin or shower. Technical specifications →see page 3!
Use
The instantaneous water heater heats the water to the required temperature directly as
it streams through. The heater switches on automatically when the threshold flow rate
is exceeded. The „Power“ indicator (2) lights up when the heater is switched on.The
„Pressure“ indicator (3) lights up when the flow rate is too low.
The power is automatically adjusted by the electronics in line with the water flow rate
in order to obtain the set temperature and keep it virtually constant. The required tem-
perature can be set to within one degree between 35°C and 55°C via the two buttons
(5) and can be read off on the digital display (4).
If the full power of the instantaneous heater is not sufficient to heat the water to the
required temperature, this is indicated by the flashing „Power“ indicator (2). The tem-
perature can be restored by reducing the hot water flow rate at the tap.
4

CRX9
Venting
To prevent damage to the appliance, the instantaneous water heater must be vented before using it for the first time.
Each time it is emptied (e.g. after work on the plumbing system, if there is a risk of frost or following repair work), the
appliance must be re-vented before it is used again.
1. Disconnect appliance from the mains by removing the fuses.
2. Next, open and close the hot water tap valve several times until no more air emerges from the pipe and all air has
been eliminated from the water heater (approx. 1 minute).
3. Only then re-connect the power supply to the unit.
Save energy
Set precisely the required temperature on the appliance and only open the hot water tap. If the water is too hot, set a
lower temperature on the appliance instead of adding cold water. If you add cold water, the heated water is cooled
again and valuable energy will be lost. Moreover, the cold water added in the fitting cannot be controlled by the elec-
tronics and a constant temperature can no longer be guaranteed.
Maintenance and cleaning
• Plasticsurfacesandttingsmayonlybewipedwithadampcloth.Neveruseabrasivecleaningagentsorsolvents.
• Foragoodwatersupply,theaeratorsandshowerheadsshouldbeunscrewedandcleanedorrenewedatregular
intervals.
• Theelectricalandplumbingcomponentsshouldbeinspectedbyanauthorizedprofessionalatleasteverythreeyears
to ensure proper functioning and operational safety at all times.
If the heater supplies two outlets, the water from the unit will be shared between the outlets. You should therefore only
use one outlet at a time in order to obtain a sufficient flow.
At high feed temperatures, the power is automatically switched off by the electronics in order to avoid producing exces-
sively hot water. This is indicated by the „Overheat“ lamp (1).
4. Operation instructions
GEFAHR
5

6
CRX9
4. Operation instructions
GEFAHR
II
I
10a
10c
10b
Cleaning the fine filter (flush-mounted)
The fine filter is located in the water connection (10) and
should be examined by an expert and cleaned if necessary
not only when operation of the appliance deteriorates, but
also in conjunction with regular servicing.
1. Disconnect the instantaneous water heater by means of
the house fuses and close the shut-off valve (10a) in the
cold water connection piece (position II) or shut-off the
mains supply.
2. Unscrew the screw plug (10b) from the cold water con-
nection piece and take out the strainer (10c).
Attention: Residual water comes out!
3. The strainer can be cleaned or replaced.
4. After fixtur of the strainer tighten the screw plug.
5. Slowly open the shut-off valve in the cold water connec-
tion piece (positionI).
6. Vent the unit by carefully opening and closing the af-
filiated warm water tap valve several times until air no
longer emerges from the pipe.
Cleaning the fine filter (surface-mounted)
The fine filter is located in the water connection (10) and
should be examined by an expert and cleaned if necessary
not only when operation of the appliance deteriorates, but
also in conjunction with regular servicing.
1. Disconnect the instantaneous water heater by means of
the house fuses and shut-off the main water supply.
2. Unscrew the cold water inlet connection of the unit and
take out the strainer (10d) of the connection piece.
Attention: Residual water comes out!
3. The strainer can be cleaned or replaced.
4. After fixture of the strainer remount the water connection
of the unit.
5. Carefully open the main water supply.
6. Vent the unit by carefully opening and closing the af-
filiated warm water tap valve several times until air no
longer emerges from the pipe.
10d

7
CRX9
GEFAHR
5. Customer service
Repairs may only be carried out by authorized professionals!
We can either give you the name and address of an authorised customer service company or repair the
heater ourselves. In the latter case, please send in the heater (at your cost and risk) with details of the
problem and a copy of the sales invoice.
If you cannot rectify the fault with the aid of this table, please contact your distributer or German Pool
Customer Service – China Headquarters.
If you experience a malfunction, please try to rectify the fault yourself first with the help of this table. If a
fault in your appliance cannot be rectified with the aid of this table, please contact German Pool who will
either assist you directly or put you in touch with a customer service contract partner in your area.
Always specify the appliance model and serial number, please!
Problem Possible Cause Solution
LED remains off, water remains cold Circuit breaker tripped Have the fault rectified and reset
The pilot lamp „Power“ lights,
water remains cold
Heating element or electronics faulty Reset fuse, water remains cold contact
customer service
Safety thermal cut-out tripped Reset. In case of repeated trips contact
customer service
The pilot lamp „Pressure“ lights,
water remains cold Flow rate too low Increase flow pressure Clean tap fitting or shower head
Water flows lower as expected
Depends on the heater Check technical specifications
Outlet fitting dirty or calcified Clean tap fitting or shower head
Filter dirty or calcified Clean or renew the filter
Tap not suitable Use suitable shower head or aerator
The hot water is not hot enough
Electronic board Reset fuse
Flow rate is too high (winter?) Reduce the water flow slightly
Heating element defect Contact customer service
Temperature and pressure vary Cold water is being added Only hot water can be delivered to within
one degree

CRX9
6. Installation
8
Installing the wall bracket (flush-mounted):
1. Thoroughly rinse the water supply pipes before installation to remove soil-
ing from the pipes.
2. Using a 12 mm hexagon socket screw key, screw the screw-in nipple into
the wall connector. After tightening, the double nipple must protrude by
12mm.
3. Carefully seal the hot water connection pipe with a little P.T.F.E. Tape and
screwed it into the wall connection. Mount the cold water connector piece
including the 1/2“ seal.
4. Hold the unit on the wall and align it so that the water connectors of the
unit fit over the connections of the wall. Mark the drill holes and drill them
using a 6 mm drill.
5. Mount the unit to the wall and connect the water supply of the unit,
together with the 3/8“ seals.
6. Open the water supply line to the unit and slowly open the shut-off valve
in the cold water connection piece (10a) (Pos.I). Check all connections for
leaks.
7. Next, open and close the hot water tapping valve several times until no
more air emerges from the line and all air has been eliminated from the
instantaneous water heater.
If you install the instantaneous water heater CRX9 instead of a conventional instantaneous water heater, there is gener-
ally no need to drill holes for the wall holder. In this case, you only need to screw in the double nipples as described in 2.
and to secure the wall bracket.

CRX9
6. Installation
9
Installing the wall bracket (surface-mounted):
1. Thoroughly rinse the water supply pipes before installation to remove soil-
ing from the pipes.
2. Screw the 1/2“ screw in nipple and the 1/2“ seal into the 1/2“ union nuts of
the hot-water connector.
3. The 1/2“ cap of the side outlets of the coldwater connectors must be
removed and screwed onto the open end of the screw-in nipple.
4. Mount the fine filter into the cold water connection piece (10d).
5. The hot-water and cold-water connectors must then be screwed into the
3/8“ union nut of the appliance and delivery pipe, together with the 3/8“
seals.
6. Mark the drill holes and drill them using a 6 mm drill. Mount the unit to the
wall and connect the water supply of the unit.
7. The holes in the housing of the unit required for the pipes must then be
broken out of the housing with the aid of a blunt implement.
8. Open the water supply line to the unit and slowly open the shut-off valve in
the cold water connection piece (drawing 10a on page 6).
Check all connections for leaks.
9. Next, open and close the hot water tapping valve several times until no
more air emerges from the line and all air has been eliminated from the
instantaneous water heater.
10d

10
CRX9
6. Installation
GEFAHR
GEFAHR
Installation instructions for the authorized technician
• Thestatutoryregulationsoftherespectivecountry,aswellasthoseofthelocalelectricity
and water supply companies.
• Thespecicationsontheratingplateandthetechnicalspecications.
Installation site
• The installation site must be free from frost at all times.
• The appliance complies with protection type IP25 and may be installed in zone 1 acc. IEC
• In order to avoid thermal losses, the distance between the heater and the tapping point
should be as small as possible (< 2 m).
• Best performance is guaranteed at a flow pressure of ≥ 3 bar, avoiding pressures exceeding
6 bar.
• Material of water pipes for tubular heater types: cold water: steel or copper, hot water:
copper
Important notice!
A backflow preventer ( )
is already provided inside
the brass connection of
the hot water outlet.
It must NOT be fitted in
the cold inlet line before
the appliance!

11
CRX9
6. Installation
Installing the appliance:
1. Rinse water supply pipes thoroughly and turn off for instal-
lation.
2. Remove the front cover by unscrewing the locking screw
behind the small lid.
3. Locate and break out the required holes and cable inlets.
Mark the drilling holes with the appliance and drill them
with a 6mm bit.
4. Fit the rubber grommet supplied and insert the connecting
lead. The lead must be secured with the cable clamp when
using a flexible power cord.
5. Screw the appliance into position using the enclosed raw
plugs and screws.
6. Install the appliance as shown in the principal examples
above. The inlet and outlet are marked with arrows.
7. The water connections are designed for surface-mounted
or flush-mounted installation. They must be carefully
sealed with a little P.T.F.E. Tape when screwed into the wall
connections.
8. The front cover must be neatly broken at the designated
points when installed on the wall.

CRX9
6. Installation
12
II
I
10a
Closed
flush-mounted
installation
9. Turn on the water supply and slowly open the shutoff valve (10a) in the
cold-water connection (position I) if necessary. Check all connections
for leaks.
10. Next, open and close the hot water tap several times until no more air
emerges from the line and all air has been eliminated from the heater.

CRX9
6. Installation
GEFAHR
13
Electrical connection:
The instantaneous water heater is an appliance of protection class I
and must be connected to the protective earth conductor!
1. Check that the power supply is switched off prior to the electrical connec-
tion!
• Theappliancemustbeconnectedtothesupplybymeansofpermanent
wiring through suitable fuses having a contact separation of at least 3mm
in all poles.
• Thecrosssectionalareaoftheconnectioncablemustbeinaccordance
with the power rating.
• Toprotecttheappliance,afuseelementmustbettedwitha
tripping current commensurate with the nominal current of the appliance.
2. Slit the grommet to match the cable size.The opening in the grommet
should be slightly smaller than the cross-section of the cable in order
to ensure optimum protection against water. Fit the grommet into the
opening. The protection grommet must be used! The appliance must be
earthed!
•Theconnectingterminalcanbetransferredtothebottomoftheappliance
if necessary.
3. Fit the front cover properly. Doublecheck whether the temperature keys
can be operated easily. If not, make sure that the cover is correctly fitted.
Secure the front cover with the fastening screw.
4. Before making the electrical connection, fill the mains and the appliance
with water by carefully opening and closing the hot water tap in order to
vent completely.
5. Explain the user how the instantaneous water heater works and
hand over the operating instructions.
6. Fill in the guarantee registration card and send it to the German Pool
Central Customer Service or use the online registration on our website
www.germanpool.com.

14
CRX9
1. 概述
1
7
2
3
4
5
6
位置 說明
1 黃銅接駁裝置
（帶有插入式回流防止器）
2 發熱線
3 顯示面板
4 安全熱切斷器 (STB)
5 電路板
位置 說明
6 流量感應器
7 電纜密封
沒有顯示： 細小的零配件
設備佈局
訂購產品零部件時，請說明產品型號、規格和序列號。

15
CRX9
2. 目錄
1. 概述 .....................................................................................................................................................................14
2. 目錄 .....................................................................................................................................................................15
3. 技術規格 .............................................................................................................................................................15
4. 操作說明 ....................................................................................................................................................16–18
5. 客戶服務 ............................................................................................................................................................ 19
6. 安裝 ............................................................................................................................................................20–25
保用條款和條件 ....................................................................................................................................................... 38
客戶服務部 .............................................................................................................................................................. 39
3. 技術規格
型號 CRX 9
容量 0.2 l
壓力類型，額定壓力 0.6 MPa (6 bar)
加熱系統 管式加熱器
額定功率 8.0 – 9.6 kW
額定電壓 (50 Hz) 1N / PE ~
220 –240 V 時的額定電流 36 – 40 A
所需導體最小橫截面 3 × 6.0 mm2
出廠預設流量減速器 5.0 升/分
當前流量下的溫度增量 ∆t 23 K
進水溫度 20 ℃ 時的熱水溫度 43 ℃
接通流速 2 升/分
預設溫度 35 – 55 ℃
冷水溫度 30 ℃
水管接駁 1/2" B.S.P. 明裝或暗裝
淨重和尺寸 (H × W × D) 2.2 kg / 33 × 21 × 9 cm
VDE 保護等級和保護類型 1 / IP25
安全標記 請參閱型號銘牌
GEFAHR
操作說明：使用設備之前，請仔細閱讀以下說明！
訂購產品零部件時，請說明產品型號、規格和序列號。

16
CRX9
4. 操作說明
封閉式出水管熱水器的安全說明：
· 本設備的安裝、初始操作和維護必須只能由經過授權的專業人士進行，他們將負責遵守適用的標準和
安裝規定。我們對由於不遵守這些說明而導致的任何損壞概不負責。
· 除非設備已正確安裝並處於最佳工作狀態，否則請勿使用設備。
· 本設備僅適用於在封閉、無霜的房間內供家庭用途和類似的應用，並且必須僅用於加熱來自幹線供給
的進水。
· 本設備永遠不得暴露在霜凍環境中。
· 本設備必須始終接地。
· 最大水壓不得超過標籤上的值。
· 初次試運行之前和每次設備排空後（例如，由於在管道系統上工作後，如果有霜凍風險或如果進行維
護時），必須根據本手冊中的說明對設備進行正確放氣。
· 任何情況下，請勿在切斷電源與設備的接駁之前拆下前蓋。
· 切勿進行技術改動（不論對設備本身還是電線和水管）。
· 請注意，水溫超過約 43 ℃ 將被視為熱水（尤其是對兒童而言），並且可能導致灼熱感。另外，設備
使用一段時間後，配件和水喉可能會非常熱。
· 進水溫度不得超過 30 ℃。
· 如果發生故障，請立即斷開保險絲。如果發生洩漏，請立即切斷冷水供給。只能由客戶服務部門或經
過授權的專業人士進行維修。
· 身體、感知或精神能力有缺陷或無法獲得經驗和/或學習知識的人士（包括兒童），必須在負責其安
全的人士監督下或瞭解如何使用本設備後方可使用。兒童應在監督下使用本設備，以免其用本設備玩
耍。
GEFAHR
設備說明
本設備為電子控制、封閉式出水的即熱式熱水器，用於加熱一個水喉或彼此
相鄰的兩個水喉（例如，洗臉盆或淋浴器）的出水。技術規格 →請參閱第
15 頁！
用途
即熱式熱水器在水流經過時將其直接加熱到所需的溫度。熱水器在流速超過
閾值後自動打開。熱水器打開時，“Power”（電源）指示燈 (2) 會亮起。
流速過低時，“Pressure”（壓力）指示燈 (3) 會亮起。
將通過電子方式控制管道中的水流速度自動調節功率，從而獲得設定的溫度
並保持近似恒定。可通過兩個按鈕 (5) 將所需溫度設置為介於 35 ℃ 到 55 ℃
之間的某一溫度，並且可從數位顯示幕 (4) 上讀出。
如果即熱式熱水器的最大功率不足以將水加熱到所需溫度，則將通過閃爍
的“Power”（電源）指示燈 (2) 表示這一情況。可通過降低水喉處的熱水
流速來恢復溫度。
如果熱水器有兩個出水口，則設備的水流將在兩個出水口之間分享。因此，
應該一次只使用一個出水口以便獲得充足的流量。
如果進水溫度較高，將通過電子方式自動關閉電源，從而避免產生過熱的熱
水。這將通過“Overheat”（過熱）燈 (1) 表示。
-
+
1 2
4
5
3

17
CRX9
放氣
為避免設備損壞，初次使用即熱式熱水器之前必須對其進行放氣。每次排空後（例如在管道系統上工作
後，如果有霜凍風險或隨後需要進行維修工作時），再次使用之前必須重新對設備進行放氣。
1. 拆下保險絲，斷開設備與電源的接駁。
2. 接下來，打開和關閉熱水喉閥門數次，直到沒有氣體從管道排出並且所有氣體均已從熱水器中排出
（約 1 分鐘）。
3. 然後將電源重新接駁至設備。
節能
在設備上精確設置所需的溫度並且只打開熱水喉。如果水過熱，請在設備上設置較低的溫度而不是添加
冷水。如果您添加冷水，則加熱的水將再次冷卻並且將浪費寶貴的能源。此外，裝置中添加的冷水無法
通過電子方式控制並且不再能夠保證恒溫。
維護和清潔
· 塑膠表面和配件只能以濕布進行擦拭。切勿使用研磨性清潔劑或溶液。
· 為供水良好，應定期取下清潔或更換通風裝置和淋浴頭。
· 電子元件和管道元件應由經過授權的專業人士至少每三年檢查一次，從而確保熱水器始終正常工作和
安全運行。
4. 操作說明
GEFAHR

18
CRX9
4. 操作說明
GEFAHR
II
I
10a
10 c
10 b
清潔細濾器（暗裝）
細濾器位於水管接駁 (10) 中，應由專家在設備運行
退化和定期維護時進行檢查和清潔。
1. 通過斷開家庭保險絲的方式斷開即熱式熱水器
的接駁，關閉冷水接駁件（位置 II）中的關閉閥
(10a) 或關閉幹線供給。
2. 旋松冷水接駁件的螺旋塞 (10b) 並取出濾網
(10c)。注意：殘留的水將流出！
3. 濾網可以清潔或更換。
4. 固定濾網後，旋緊螺旋塞。
5. 慢慢打開冷水接駁件（位置 I）中的關閉閥。
6. 將設備放氣，方法是小心地打開和關閉相連的熱
水喉閥門數次，直到不再有氣體從管道中排出。
清潔細濾器（明裝）
細濾器位於水管接駁 (10) 中，應由專家在設備運行
退化和定期維護時進行檢查和清潔。
1. 通過斷開家庭保險絲的方式斷開即熱式熱水器的
接駁，關閉幹線供水。
2. 旋松設備的冷水進水接駁裝置並從接駁件取出濾
網 (10 d)。注意：殘留的水將流出！
3. 濾網可以清潔或更換。
4. 固定濾網後，請重新接駁設備水管。
5. 小心地打開幹線供水。
6. 將設備放氣，方法是小心地打開和關閉相連的熱
水喉閥門數次，直到不再有氣體從管道中排出。
10d

19
CRX9
GEFAHR
5. 客戶服務
如果您遇到故障，請首先嘗試借助此表格自行修復故障。如果借助此表格無法修復設備的故障，
請聯繫 German Pool，我們將直接為您提供幫助，或幫助您與當地的客戶服務簽約合作夥伴
進行聯繫。
請務必指定設備型號和序列號！
故障 可能的原因 解決方案
LED 不亮，水不熱 電路斷路器已觸發 修復該故障並重定
“Power”（電源）指示燈亮
起，水不熱
發熱線或電子設備故障 重定保險絲，如果水仍然不熱，
請聯繫客戶服務
安全熱切斷器已觸發 復位。如果反復跳閘，請聯繫
客戶服務
“Pressure”（壓力）指示燈亮
起，水不熱 流速過低 增加流量壓力清潔水喉配件或 淋浴頭
水流過低
取決於熱水器 查看技術規格
出水管配件髒汙或鈣化 清潔水喉配件或淋浴頭
過濾網髒汙或鈣化 清潔或更換過濾網
水喉不合適 使用合適的淋浴頭或通風裝置
熱水不夠熱
電路板 復位保險絲
流速過高（冬季？） 稍微減少水流量
發熱線故障 聯繫客戶服務
溫度和壓力變化 添加了冷水 只提供某一度範圍內的熱水
只能由經過授權的專業人士進行維修！
我們可能會向經過授權的客戶服務公司提供您的姓名和地址，也可能會自己維修熱水器。
如果是後一種情況，請遞交熱水器（自行承擔費用和風險）及問題詳情和銷售發票的副本。
如果借助此表格無法修復故障，請聯繫您的分銷商或德國寶客戶服務總部。

20
CRX9
6. 安裝
安裝掛牆背碼（暗裝）：
1. 安裝前，仔細清洗供水管道，以除去管道中的髒汙。
2. 使用 12 mm 的內六角形螺釘扳手，將旋入式管接頭旋入牆壁接
頭中。旋緊後，雙向管接頭必須突出 12 mm。
3. 使用少量 P.T.F.E. 仔細密封熱水接駁管。將其用帶子固定並旋入
牆壁接駁裝置中。裝配附帶 1/2" 密封件的冷水接駁件。
4. 握住牆壁上的設備並將其對齊，以便設備的水管接頭裝在牆壁接
駁裝置上。標記鑽孔位置並使用 6 mm 鑽來鑽孔。
5. 將設備裝到牆上並接駁設備的水源，以及 3/8" 密封件。
6. 打開設備的供水管道並慢慢打開冷水接駁件 (10 a)（位置 I）中
的關閉閥。檢查所有接駁有無洩漏。
7. 接下來，打開和關閉熱水喉閥門數次，直到沒有氣體從管道排出
並且所有氣體均已從即熱式熱水器中排出。
如果您安裝的是即熱式熱水器 CRX 9 而不是傳統的即熱式熱水器，則通常牆壁固定支架不需要鑽孔。
在這種情況下，您只需要如 2 中所述旋緊雙向管接頭並固定掛牆背碼即可。