GFA ELEKTROMAT ST 16.24 User manual

f
Installation Instructions
ELEKTROMAT
ST 16.24-40,00
Model: 10002992 00024
-en-
Status: 22.11.2019

2
GfA ELEKTROMATEN GmbH & Co. KG
Wiesenstraße 81
D-40549 Düsseldorf
www.gfa-elektromaten.de
[email protected]

3
Table of contents
1General safety information .............................................................................................. 4
2Technical Data ................................................................................................................ 5
3Mechanical installation .................................................................................................... 6
4Electrical installation ..................................................................................................... 10
5Motor connection .......................................................................................................... 11
6Limit switch connection ................................................................................................. 11
7Completing commissioning / inspection ......................................................................... 12
8Declaration of incorporation / Declaration of conformity ................................................. 14

Symbols
Warning - Potential injury or danger to life!
Warning - Danger to life from electric current!
Note - Important information!
▶ Requirement - Required action!
Schematic representations are based on product examples. Deviations from delivered
products are possible.

4
1General safety information
Specified normal use
The drive unit is intended for horizontally operating sliding doors.
The safe operation is only guaranteed with specified normal use. The drive unit is to be
protected from rain, moisture and aggressive ambient conditions. No liability for damage
caused by other applications or non-observance of the information in the manual.
Modifications are only permitted with the agreement of the manufacturer. Otherwise the
Manufacturer’s Declaration shall be rendered null and void.
Safety information
Installation and initial operation tasks are to be performed by skilled personnel only.
Only trained electrical craftsmen are permitted to work on electrical equipment. They must
assess the tasks assigned to them, recognise potential danger zones and be able to take
appropriate safety measures.
Installation work is only to be carried out with the supply off.
Observe the applicable regulations and standards.
Coverings and protective devices
Do not operate unless corresponding coverings and protective devices are installed.
Ensure that gaskets are fitted correctly and that cable glands are correctly tightened.
Spare parts
Only use original spare parts.

5
2Technical Data
Type SG 85R
Output torque 160 Nm
Output speed 24 rpm
Output shaft / hollow shaft 40,00 mm
Maximum output speed open / close
for frequency inverter operation 42 / 42 rpm
Maximum door weight 16000 N
Supply voltage 3N~ 400 V
Operating current 1,80 A
Operating frequency 50 Hz
Power factor cos φ 0,51
Maximum movement per hour 20 h-1
Class of protection IP 54
Limit switch range
(maximum revolutions of output shaft / hollow shaft) 20
Braking torque of magnetic brake 130 Nm
Braking voltage 103 V DC
Rectifier type B1 230/103
Temperature range -10 / +40 (+60) °C
1) When using a temperature range of +40°...+60°C use half of maximum movements per hour.
Temperature Extension!
If the magnetic brake will be continuously supplied the drive can be fitted into areas
down to a -20°C ambient temperature.

6
3Mechanical installation
Prerequisites
The permissible loads on walls, fastenings, mountings and transmission elements must not
be exceeded, even for maximum holding torques or locking torques (▶ refer to technical
data).
Connection elements
▶ Self-locking connection
elements with a minimum
strength of 800 N/mm2
(8.8) must be used.
▶ Utilize the hole diameter
to the full.
▶ Use adequately
dimensioned washers for
elongated holes.
BA GAB00002_Z002 BAGAB00003_Z002
3 : 1
Permissible mounting positions
BAGAC03301_Z002

7
Mounting
Four holes are provided for mounting.
BAGAD03301_Z002

8
Installation
The descriptions below apply to general door specifications. The specifications of the door
manufacturer must also be observed during installation.
Warning - Potential injury or danger to life!
During installation, be sure to use a lifting device that has a sufficient load-
carrying capacity.
Ensure that there is sufficient space around the handwheel for safe operation of
the friction clutch.
▶ The output-shaft must not be shortened.
BAGAE03301_Z001
▶ Tighten all connection elements (M12) to
75 Nm. Install all other connection
elements according to the specifications of
the door manufacturer.
BAGAE003302_Z002
75 Nm

9
Warning - Potential injury or danger to life!
Disconnect the electric supply to set the friction clutch.
The friction clutch provides overload
protection. It is tightened finger-tight at the
factory. Turning to the right (handwheel or
screw) increases the transferable torque.
Turning to the left decouples the drive unit
from the door (does not apply to version with
floor release).
BAGAE3303_Z002

10
4Electrical installation
Warning - Danger to life from electric current!
Switch the mains OFF and check that the cables are de-energised
Observe the applicable regulations and standards
Make the electrical connection according to standard
Use suitable tools
Performing electrical installation
Remove the cover. Connect the motor cables
and brake cables.
BAH AA17_Z001
BAH AB0 8 _ Z0 01
Completing the electrical installation
Mount the cable entries and/or cable glands.