Giada PC610 User manual

- 1 -

- 2 -
Statement
The copyright of this manual belongs to Shenzhen JEHE Technology Development Co., Ltd.
(Giada, JEHE’s global brand) and all rights are reserved. The company reserves the right to
change this manual at any time without notification. Specifications here are for reference only,
please take the real product as standard.
Without official authorization of Giada, other companies or individuals may not copy,
plagiarize, translate, or disseminate this manual for commercial purpose.
The information provided in this manual is accurate and reliable. The company does not take
any legal responsibility for the consequences of infringement use of this manual.
Safety Notice
• Read the user manual carefully before setting up the Giada product.
• Disconnect the power before installing the internal components
• Most electronic components are sensitive to static electrical charge, please wear a
wrist-grounding strap when installing the internal components.
• Do not disconnect the power when the system is running to avoid damage to the sensitive
components by instantaneous surge voltage.
Contact Information
Shenzhen JEHE Technology Development Co., Ltd.
Website: www.giadatech.com
Phone: [phone]
Email: [e-mail]
Address: 1~3/F, Block A, Tsinghua Information Harbor, North Section, Shenzhen Hi-tech
Park, Nanshan District, Shenzhen, China

3
Table of Contents
1. Product Introduction ........................................................................................ 5
2. Interface Description and Hardware Specifications ...................................... 5
2.1 Interface Description .................................................................................... 5
2.2 Hardware Specifications ............................................................................... 6
3. Accessories Installation Steps ........................................................................... 7
3.1 CPU Installation ............................................................................................. 7
3.2 Memory Installation ....................................................................................... 8
3.3 SSD (M.2) Installation ................................................................................... 9
3.4 WIFI (M.2) Installation ................................................................................ 10
4. BIOS Setup ....................................................................................................... 11
4.1 Main (Standard CMOS Setup) .................................................................... 14
4.2 Advanced (Advanced BIOS Setup) ............................................................. 15
4.2.1 ACPI Setting ....................................................................................... 15
4.2.2 CPU Configuration ............................................................................. 16
4.2.3 Super IO Hardware Monitor .............................................................. 18
4.2.4 Super IO Configuration ...................................................................... 21
4.2.5 OEM Configuration ........................................................................... 23
4.2.6 OEM ME Configuration .................................................................... 24
4.2.7 System Devices Configuration .......................................................... 25

4
4.3 Security ....................................................................................................... 28
4.4 Boot Menu ................................................................................................... 29
4.5 Save & Exit ................................................................................................. 30
5. JAHC Introduction ......................................................................................... 31
5.1 Auto Power On ............................................................................................ 31
5.2 JAHC Software ........................................................................................... 34
5.2.1 JAHC Software Function ..................................................................... 34
5.2.2 JAHC Software Installation Guide ....................................................... 34
5.2.3 Startup & Shutdown Time Setup ......................................................... 37
5.3 Watchdog API & Instruction ....................................................................... 39

5
1. Product Introduction
Complies with Intel OPS standard and based on Intel®Comet Lake platform, Giada PC610 adopts
DDR4 dual-channel memory (Max 32GB) as well as M.2 storage interface design. With selectable
desktop processors, it provides high computing and graphics performance. The player is suitable to
be applied in interactive white board, video conference and other high-end digital signage
applications.
2. Interface Description and Hardware Specifications
2.1 Interface Description
Front I/O Port
Rear I/O Port

6
2.2 Hardware Specifications
PC610
Processor
CPU
Intel®LGA1200 Socket 10th / 11th Gen. Processor
BIOS
AMI Source Code
Chipset
Intel®H470 (Optional Q470/H420E)
Memory
Type
DDR4-2666MHz
Socket
2 x SO-DIMM
Max Capacity
32 GB
Graphics
DP (80 Pin JAE)
1 x DP (Max.4096 x 2304 @ 60Hz)
HDMI (80 Pin JAE)
1 x HDMI (Max.4096 x 2304 @ 60Hz)
HDMI
1 x HDMI (Max.4096 x 2304 @60Hz)
Network
Controller
Realtek 8111H Gigabit Ethernet
Interface
1 x RJ45
I/O Interface
USB
2 x USB 3.2 Gen1, 2 x USB 3.2 Gen2
1 x USB Type-C 3.2 Gen1 (H470)
4 x USB 3.2 Gen1
1 x USB Type-C 3.2 Gen1 (H420E)
Audio
1 x MIC-in, 1 x Audio-out
Serial Port
1 x UART (JAE)
M.2
1 x M.2 (2230) E-KEY for WIFI/BT
TPM
Infineon TPM 2.0
Storage
M.2
1 x M.2 (2242/2280) for SSD
Operation
System
Windows (Optional)
Windows 10（64-bit)
Linux
Supported
Power
Power Type
2.5/5/5 DC Jack / 12V~19V
80 Pin JAE DC-IN / 12V~19V
Mechanical
Construction
Metal
Dimension
(W x D x H)
200mm x 119mm x 30mm (7.87’’ x 4.69’’ x 1.18’’)
Color
Black
Environment
Operating
Temperature
0℃~ 40℃( 32 ℉~ 104 ℉) at 0.7m/s Air Flow
Relative Humidity
95%@40℃(non-condensing)
Certification
CE, FCC

7
3. Accessories Installation Steps
For safety reasons, please ensure that the power is disconnected before opening the case.
How to open the top cover and bottom cover
Unscrew the seven screws and remove the top cover. (CPU, SO-DIMM #1 and M.2 for WIFI are on
top side)
Unscrew the three screws and remove the two covers. (SO-DIMM#2 and M.2 for SSD are on bottom
side)
3.1 CPU Installation
1. Unscrew the screws and remove the CPU cooler.
2. Remove the hook to open the closure.
3. Put the CPU on the board and paint the top side with heat conduction grease.
4. Remove the closure and put the hook back.
5. Tighten up the screws.

8
3.2 Memory Installation
This product only supports DDR4 SO-DIMM memory modules.
1. Locate the SO-DIMM slot on the board.
2. Gently insert the module into the slot in a 45-degree angle.
3. Carefully push down the memory module until it snaps into the locking mechanism.

9
3.3 SSD (M.2) Installation
1. Plug the SSD (M.2) into the appropriate slot.
2. Secure the module to the carrier by tightening up the screw.
3. Remove the clear membrane of the thermal pad and paste the pad on the SSD.
4. Remove the blue membrane of the thermal pad.

10
3.4 WIFI (M.2) Installation
1. Plug the WIFI module into the appropriate slot.
2. Secure the module to the carrier by tightening up the screw.
3. Connect the two black cables to Main and AUX. Install antennas.
Hot-plugging may cause damage to the OPS PC. Please disconnect the power of the
monitor before installing the OPS PC into the slot.

- 11 -
4. Bios Setup
Notice:
The descriptions relating to BIOS setup in this Manual is for reference only since the BIOS version
of the product might be upgraded. Giada provides no guarantee that all the contents in this Manual
are consistent with the information you acquired.
BIOS is a basic I/O control program saved in the Flash Memory. Bridging the motherboard and the
operation system, BIOS is used for managing the setup of the related parameters between them.
When the computer is activated, the system is first controlled by the BIOS program. Firstly, a
self-detection called POST is performed to check all hard devices and confirm the parameters of the
synchronous hardware.
Once all detections are completed, BIOS will hand over the controlling to the operation system (OS).
As BIOS serves as the only channel that connects the hardware and software, whether your computer
can run stably and work in optimized state will hinge on how to properly set the parameters in BIOS.
Therefore, the correct setup of BIOS plays a key role in stably running the system and optimizing its
performance.
The CMOS Setup will save the set parameters in the built-in CMOS SRAM on the motherboard.
When the power is shut off, the lithium battery on the motherboard will provide continuously power
to CMOS SRAM.
The BIOS setup program will allow you to configure the following items:
1. HD drive and peripheral devices
2. Video display type and display items
3. Password protection
4. Power management characteristics
A. State of BIOS Setup
When the computer is started up, BIOS will run the self-detection (Post) program. This program includes
series of diagnosis fixed in BIOS. When this program is executed, the following information will appear if
any error is found:
Press [F1] to Run General help
Press [F2] to Load previous values and continue
To enter BIOS, you can press F2; to load the default values and enter the system, you can press DEL to enter
the BIOS interface if no error is found. If the indicative information disappears before you operate, you can
shut off the computer and turn it on again, or you can press the RESET key on the product case. To restart
your computer, you can also simultaneously press < Ctrl > + < Alt > + < Delete >.

- 12 -
B. Function Keys definitions
Hot Key
Description
↑
(Up key) Move to the previous item
↓
(Down key) Move to the next item
←
(Left key) Move to the left item
→
(Right key) Move to the right item
ESC
Exit the current interface
F1
Display the information of the current function Keys definitions.
F9
Load the optimized values
F10
Save the settings and exit the CMOS SETUP
C. Auxiliary information Main interface
When the system enters the main interface of Setup, the major selected contents will be displayed at
the lower part of the interface with the change of the options.
When you set the value for each column, you can view the preset value of the column and the values
that can be set if you press F2, for example, the BIOS default values or CMOS Setup values.
To exit the interface for auxiliary information, press [ESC].
1) Main menu
When the system enters the CMOS Setup menu, you can see the main menu on the upper part of the screen, as
shown in Figure1.
In this main menu, you can use the left and right direction keys to select the setup items.
Once the item is selected, the lower part of the computer screen will show the details of setting.

- 13 -
Fig 1
1) Main (standard CMOS setup)
This item is used for setting the date and time.
2) Advanced (advanced BIOS setup)
This item is used for setting the advanced functions provided by BIOS, such as specifications of PCIe facilities,
CPU, HDD, etc.
3) Security (set the administrator/user password)
4) Boot (startup configuration characteristics)
5) Save & Exit (option of exit)
This item includes load optimal defaults / load failsafe defaults value / discard changes / discard changes and exit.

- 14 -
4.1 Main (Standard CMOS Setup)
1) System time (hh:mm:ss)
Use this item to set the time for the computer, with the format as “HH / MM / SS”.
2) System date (mm:dd:yy)
Use this item to set the date for the computer, with the format as “week, MM / DD / YY”.

- 15 -
4.2 Advanced (Advanced BIOS Setup)
4.2.1 ACPI Setting

- 16 -
ACPI Setting Menu
Description
ACPI Sleep state
You can use the ACPI Sleep state option to control system hibernation
Suspend Disabled: Disable system Suspend.
S3 (Suspend to RAM): Enable S3(Suspend to RAM)
State After G3
State After G3 means after restore power supply.
S5 State (Default): If set it as S5 State, it means the system will remain
shutdown state
S0 State: If set it as S0 State, it means the system will be power on
automatically.
Wake system from S5
Disabled: By default, the functions is disabled.
Fixed Time: You can use the fixed Time menu to modify the wake time.
Dynamic Time: You can set multithreaded to wake system from S5 after
enabling Dynamic Time.
Wakeup By USB KB/MS
Enabled or Disabled Wake Up by USB KB/MOUSE from S3 Status.
Disabled: The wake on USB is disabled by default.
Enabled.
4.2.2 CPU Configuration

- 17 -
CPU Configuration Menu
Description
CPU Configuration
Boot performance mode
Max Non-Turbo Performance: the best performance.
Max Battery.
Turbo performance.
Intel (VMX) Virtualization Technology
Intel Virtualization Technology is enabled by default. User
can enable and disable the Intel Virtualization Technology
function.
Intel（R）SpeedStep（tm）
Intel（ R）SpeedStep Technology dynamically increases the
processor's frequency as needed by taking advantage of
thermal and power headroom to give you a burst of speed
when you need it, or increased energy efficiency.The option
is enabled by default. You can disable the function if it’s
necessary.
Race To Halt（RTH）
The Race To Halt（ RTH）function is enable by default. It can
adjust the CPU base frequency work in C-state.
Optional: C-state.

- 18 -
Intel（R）Speed Shift Technology
Intel speed shift function is enabled by default. Intel®Speed
Shift Technology uses hardware-controlled P-states to
deliver dramatically quicker responsiveness with
single-threaded, transient (short duration) workloads, such as
web browsing, by allowing the processor to more quickly
select its best operating frequency and voltage for optimal
performance and power efficiency.
Hyper-Threading
Intel Hyper-Threading technology is enabled by default. Intel®
Hyper-Threading Technology (Intel®HT Technology) delivers
two processing threads per physical core. Highly threaded
applications can get more work done in parallel, completing
tasks sooner.
C states
The C-State function is disabled by default.
Turbo Mode
Disabled.
Enabled.
4.2.3 Super IO Hardware Monitor

- 19 -
Menu
Description
Pc Hardware Monitor Status
Smart Fan2 Function
It includes "Full on mode", "Smart Fan"and "manual mode".
Full on mode.
Smart Fan: Smart Fan is enabled by default.
Manual Mode.
Fan off temperature limit
FAN will stop work If temperature is lower than the Fan off
temperature limit value.
Fan start temperature limit
If the temperature is higher than fan off temperature limit, FAN
will start work.
Fan start PWM
If the temperature is higher than the FAN start PWM value, the
FAN will start work.
Fan Full Speed Temp limit
If the temperature is higher than the FAN Full Speed temp limit
value, the FAN will work at full speed.
PWM slope setting
1 PWM
2 PWM
4 PWM

- 20 -
Smart Fan Function
It includes "Full on mode", "Smart Fan"and "manual mode".
Full on mode.
Smart Fan: Smart Fan is enabled by default.
Manual Mode.
Fan off temperature limit
FAN will stop work If temperature is lower than the Fan off
temperature limit value.
Fan start temperature limit
If the temperature is higher than fan off temperature limit, FAN
will start work.
Fan start PWM
If the temperature is higher than the FAN start PWM value, the
FAN will start work.
PWM slope setting
1 PWM
2 PWM
4 PWM
8 PWM
System temperature
Current System Temperature.
CPU temperature
Current CPU Temperature.
CPU Fan2 Speed
Current FAN2 Speed.
CPU Fan Speed
Current FAN Speed.