Giani HPW-1004-55 User manual

Instruction Manual
Pressure Washer
HPW-1004-55

Contents
6Technical Specications
Giani Limited, River House, Unit 17, Shepley Industrial Estate South,
Manchester. UK. M34 5DW
Page Number
1Introduction
2Features
3Getting Started
4Saftey Warnings
5Trouble Shooting
Congratulations on choosing to buy a Giani product. All products
brought to you by Giani are manufactured to the highest standards of
performance and safety,
We hope you will enjoy using you purchase for many years to come.
Function:
This product is designed for domestic washing and cleaning of cars,
motorbikes, caravans, patios etc.

02
Features
Power Switch
Power Jet Washer Unit
Handle
Jet Wash Lance Holder
Trigger Switch
Jet Wash Gun
Hose Fitment
Extension Lance
Spray Lance
Water Hose
Hose Attachment Fitment
Detergent Container

03
Getting Started
1.0 General Use of the Jet Washer:
1. Firstly ensure that the power switch is depressed in the“O”
position to ensure the washer unit is switched o.
2. Connect the spray lance and the water source pipe to the washer
unit.
3. Connect the water source pipe to your indoor or outdoor tap.
4. Connect your washer to the mains power, using the power plug.
[Important] The plug must only be connected to an indoor socket
protected by an RCD circuit breaker.
5. To turn on the washer depress the “On” button on the washer.
6. To begin sraying pull the trigger on the jet wash lance.
7. When using the washer if you wish to change the power of water
jet twist the end of the spray gun nozzel to achieve desired water
jet power.
8. When you have nished using the jet wash ensure that you have
disconnected the plug from the mains supply before preparing the
unit for storage.

• Please conrm the voltage and socket are appropriate.
• Please use clean water only.
• Please only use the attachments supplied, use of other
attachments may cause damage to the pressure washer.
• The unit has an auto-stop function, When you close the spray gun
(by twisting the end of the nozzel until water stops) the motor will
be stopped. However please ensure that the washer is completely
shut o if leaving for longer than 10 minutes, as this will cause
damage to the unit.
• Please store the unit in a dry place after use.
• Please inspect the water lter on a regular basis.
• Do not use your washer in adverse weather conditions.
• Do not direct the water jet at persons or animals as this may result
in injury.
• Do not use the washer if the product becomes damaged in any
way.
• Do not allow children to use this product.
PLEASE NOTE: This High Pressure Washer is tted with a automatic on/
o function. It will only be activated when you stop holding down the
trigger.
This appliance complies with the requirements of Directives 89/336
EEC (Electromagnetic Compatibility) and 73/23/EEC (Electrical Safety of
Domestic Appliance), amended by Directive93/68/EEC (CE Marking).
04
Saftey Warnings

Trouble Shooting
05
Fluctuating Pressure. 1. Pump sucking air.
2. Valves dirty, worn out or
stuck.
3. Pump seals worn out.
1. Check that hoses and
connections are air-tight.
2. Clean and replace, or refer to
manufacturer
Water leaking from the pump. 1. Seals worn out. 1.Check and replace or refer to
manufacturer
The motor stops suddenly. 1. Thermal saftey switch has
tripped due to over heating
1.Check that the mains voltage
corresponds to specications
2. Switch o the unit and let it
cool for a few minutes.
The pump does not reach the
necessary pressure.
1. Water inlet lter is clogged.
2. Pump sucking air from
connections or hoses.
3. Suction/Delivery valves are
clogged or worn out.
4. Unloaded valve is stuck.
5. Lance nozzel incorrect or
worn out.
1. Clean the water inlet lter.
2. Check that all supply
connections are tight.
3. Check that the water feed-
ing hose is not leaking.
4. Clear or replace valves.
5. Loosen and re-tight regula-
tion screw.
6. Check and/or replace.
When switched on the unit
does not start working.
Fault RepairProbable Cause
1. Plug is not well connected
or electric socket is faulty
2. The main voltage is insu-
cient, lower than minimum
requiremnet.
3. The pump is sucking air
4. Thermal saftey switch has
tripped.
1. Check plug, socket and
fuses.
2. Check that the mains volt-
age is adequate.
3. Refer to after strorage
instructions.
4. Switch o the unit and let
the motor cool for a few
minutes.
5. leave lance open

Technical Specication
06
UK Guarantee
This appliance is guaranteed for consumer use for 12 months.
This guarantee covers defects under normal use from date of
purchase and ceases to be valid in the event of alteration or repair by
unauthorized persons.
This guarantee in no way aects your statutory rights.
Technical Specication
• Model: HPW1104-55
• Functions: For washing and cleaning outdoor equipment
• Voltage: AC230V 50Hz
• Power: 1100W
• Water Pressure: >0.15Mpa
• Temprature water source: 6~42C
• Max Flow: 5L/Min
Disposal Information
Do not dispose of this item in normal household waste. Used
electrical and electronic equipment must be disposed of separately.
Please contact your local waste disposal authority for details of local
arrangements.
THIS APPLIANCE IS EARTHED
IF THE SUPPLY CABLE OR CORD IS DAMAGED DO NOT USE.
IF IN DOUBT CONTACT A QUALIFIED ELECTRICIAN
FOR DOMESTIC USE ONLY

Giani Limited
River House,
Unit 17, Shepley Industiral Estate South,
Manchester,
M34 5DW