Gigabyte GD-1503BP User manual

Warning card
FCC Declarationof Conformity
CE EUDeclaration ofConformaty
12
13
14

Your monitor
Pedestal
AC Powercord
D-sub Signal cable
This manual

step 1 step 2 step 3
2.1 Installthe pedestal
To attachthe baseto yourmonitor,please followingthe stepsfor
installation ofthe pedestalas below:
(1) VGA Signal Cable
Note: (3) only for monitor with speaker function
Audio in
(3)
AC Power cable
(2)
2.2.1 Turn off your computer and unplug its power cable.
2.2.2 C power jack on the back of your monitoronnect the power cord to the .
2.2.4 Plug the computer and monitor power cables into a nearby outlet.
Turn your computer and monitor on, if your monitor display an image, you
have successfully installed the monitor. If the monitor does not display an
Image, check all the connections.
2.2.3

1 2 2 3 4 5
(1) VGA Signal Cable
Note: (3) only for monitor with speaker function
Audio in
(3)
AC Power cable
(2)
1 VGA Signal Cable
2 AC Power cable
3 Audio cable

4.1 SWITCHINGTHE MONITORON/OFF
This ON/OFF buttonis used forswitching the monitoron and off.
Note: TheON/OFF switch doesnot disconnect thedevice from the
mains voltage.To completelydisconnect the mainsvoltage.
Please remove thepower plug fromthe socket.
4.2 POWERINDICATOR
This indicator lightsup green orblue when themonitor operates normally.
if the monitoris in powersaving mode,this indicator changeto orange.
when monitor isturn off, this indicatorchange the colorto dark.
4.3 VOLUME
This feature adjustthe button todecrease the volumeand
button to increasethe volume.
Important information onaudio playback
To achieveoptimum sound qualityfrom the monitorspeakers,
the audio cableshould be connectedto the Line-Outsocket
(headphone socket)of the computer. If youconnect the audiocable
to the Speaker-Out socket(soundcard) of thecomputer,Please set
the volume underWindows to rangebetween 20% -40% of the
maximum value toachieve optimum soundquality.
4.4 MENUFEATURES
The following featurescan all beaccessed by usingyour monitor's on
screen menu system. Once arefinished. Makingadjustments to afeature,
selecting the exiticon to turnoff the menu.
Please follow theprocedure of selectionand adjust anitem using theOSD
system as belowsteps for mainfunctions adjustment.
Step 1: Press the button to activatethe OSD menu.
The main menuappears on thescreen with iconsfor the
setting functions.
Step 2: If necessary,use the or button to markan
other icon.
Step 3: Press the button to activatethe highlighted icon.
Step 4: Use the or button to make the desiredsetting.
Step 5: Select the EXITsymbol to exitthe OSD menu.
Step 6: Repeat step2 through 5to makefurther adjustments.
All changes arestored immediately

Color Select Menu
4.5

4.6
Mode Resolution Horizontal Vertical
1720 x 400 31.47 kHz 70 Hz
2640 x 480 31.47 kHz 60 Hz
3640 x 480 37.86 kHz 72.8 Hz
4640 x 480 37.5 kHz 75 Hz
5800 x 600 37.88 kHz 60.3 Hz
6800 x 600 48.08 kHz 72.2 Hz
7800 x 600 46.87 kHz 75 Hz
81024 x 76848.36 kHz 60 Hz
91024 x 768 56.48 kHz 70.1 Hz
10 1024 x 768 60.02 kHz 75 Hz
11 1280x1024 63.98 kHz 60.02 Hz
12 1280x1024 80.0 kHz 75 Hz

5.1 Products Specifications
Inch Size
Max.
Resolution
Recommend Resolution
Horizontal Freq.
Vertical Freq.
Active Display Area
Bandwidth
User Control
OSD Functions
Adapter power input
Power Consumption
(under)
Connector Signal
Dimension (Packing)
Weight Gross/Net
Multimedia Feature
1024*768@75Hz
1024* Hz
30-60 KHz
60-75 Hz
304*228 mm
80 MHz
4 Key Sw
gBri htness, contrast,
H-position,V-position,
H-Size, phase, Color, auto,
Reset, language, OSD, Exit,
AC 100V to 240 V
36 W
D-Sub 15Pin
408 (W) x 400(H) x 140 (D) mm
4.8 Kg/3.3 Kg
Ÿ
15"
2.0W +2.0W
NOTE: All technicalspecifications are subjectto change withoutnotice.
Technical Information
768@60

5.2 Signal connector pin assignment

Even the normal pixels on the LCD
screen reach 99.99% or higher, there
may be 0.01% or less pixels showing
dark or light while displaying.
5.3 Visual Inspection

5.4 Troubleshooting
Before callingfor service,check theinformation inthis sectionto seeif you
can remedyany problemsby yourself.If youneed assistance,please callthe
dealer whereyou purchasedthe LCDmonitor.
There isno SCREENimage
The powercord issecurely connectedto themonitor,the adaptor, and
the wall outlet.
Check thesignal cableconnection betweenthe monitorand thecomputer.
Adjust the brightnessand contrast controls.
Monitor inpower savingmode.
Display imageis too large ortoo small
Use theOSD controlsto adjustAutoSetup.
The colorsare distorted
Signal cableproperly connected.
Use OSDcontrols toadjust thecolor controlsetting.
The imageis toolight ortoo dark
Use OSD controlsto adjust thebrightness and contrast.
There isno soundor soundis low
Check thesound cableconnection
Make surethe computersound programis working
Adjust thevolume onsound setting.Adjustyour soundcard or
computer volumesetting.
Adjust thevolume controlkeys onthe monitor

Warning Card
12

13

14