Gigabyte R262-ZA0 User manual

R262-ZA0
AMD EPYC™ 7003 Server System - 2U 42-Bay
User Manual
Rev. 1.0

Copyright
© 2021 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.
The trademarks mentioned in this manual are legally registered to their respective owners.
Disclaimer
Information in this manual is protected by copyright laws and is the property of GIGABYTE.
Changes to the specications and features in this manual may be made by GIGABYTE without
prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or
published in any form or by any means without GIGABYTE's prior written permission.
Documentation Classications
In order to assist in the use of this product, GIGABYTE provides the following types of documentation:
 User Manual: detailed information & steps about the installation, conguration and use of this
product (e.g. motherboard, server barebones), covering hardware and BIOS.

User Guide: detailed information about the installation & use of an add-on hardware or
software component (e.g. BMC rmware, rail-kit) compatible with this product.
Quick Installation Guide: a short guide with visual diagrams that you can reference easily for
installation purposes of this product (e.g. motherboard, server barebones).
Please see the support section of the online product page to check the current availability of these
documents.
For More Information
For related product specications, the latest rmware and software, and other information please visit our website at
http://www.gigabyte.com
For GIGABYTE distributors and resellers, additional sales & marketing materials are available from our reseller
portal: http://reseller.b2b.gigabyte.com
For further technical assistance, please contact your GIGABYTE representative or visit
https://esupport.gigabyte.com/ to create a new support ticket
For any general sales or marketing enquiries, you may also message GIGABYTE server directly by email:
server[email protected]

Conventions
The following conventions are used in this user's guide:
NOTE!
Gives bits and pieces of additional
information related to the current topic.
CAUTION!
Gives precautionary measures to
avoid possible hardware or software problems.
WARNING!
Alerts you to any damage that might
result from doing or not doing specic actions.

Server Warnings and Cautions
Before installing a server, be sure that you understand the following warnings and cautions.
WARNING!
To reduce the risk of electric shock or damage to the equipment:
• Do not disable the power cord grounding plug. The grounding plug is an important safety
feature.
• Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all
times.
• Unplug the power cord from the power supply to disconnect power to the equipment.
•
• Shock Hazard! Disconnect all power supply cords before servicing.
• Do not route the power cord where it can be walked on or pinched by items placed against it.
Pay particular attention to the plug, electrical outlet, and the point where the cord extends from
the server.
WARNING!
To reduce the risk of personal injury from hot surfaces, allow the drives
and the internal system components to cool before touching them.
WARNING!
This server is equipped with high speed fans. Keep away from hazardous
moving fan blades during servicing.
WARNING!
This equipment is not suitable for use in locations where children are
likely to be present.
CAUTION!
• Do not operate the server for long periods with the access panel open or removed. Operat-
ing the server in this manner results in improper airow and improper cooling that can lead to
thermal damage.
• Danger of explosion if battery is incorrectly replaced.
• Replace battery with the same or equivalent type recommended by the manufacturer.
• Dispose of used batteries according to the manufacturer’s instructions.
CAUTION!
Risk of explosion if battery is replaced incorrectly or with an incorrect type. Replace the battery
only with the same or equivalent type recommended by the manufacturer. Dispose of used bat-
teries according to the manufacturer’s instructions.

Electrostatic Discharge (ESD)
CAUTION!
ESD CAN DAMAGE DRIVES, BOARDS, AND OTHER PARTS. WE RECOMMEND THAT YOU
PERFORM ALL PROCEDURES AT AN ESD WORKSTATION. IF ONE IS NOT AVAILABLE,
PROVIDE SOME ESD PROTECTION BY WEARING AN ANTI-STATIC WRIST STRAP AT-
TACHED TO CHASSIS GROUND -- ANY UNPAINTED METAL SURFACE -- ON YOUR SERVER
WHEN HANDLING PARTS.
Always handle boards carefully. They can be extremely sensitive to ESD. Hold boards only by
their edges without any component and pin touching. After removing a board from its protective
wrapper or from the system, place the board component side up on a grounded, static free sur-
face. Use a conductive foam pad if available but not the board wrapper. Do not slide board over
any surface.
System power on/o󰀨: To remove power from system, you must remove the system from
rack. Make sure the system is removed from the rack before opening the chassis, adding, or
removing any non hot-plug components.
Hazardous conditions, devices and cables: Hazardous electrical conditions may be
present on power, telephone, and communication cables. Turn off the system and disconnect the
cables attached to the system before servicing it. Otherwise, personal injury or equipment dam-
age can result.
Electrostatic discharge (ESD) and ESD protection: ESD can damage drives,
boards, and other parts. We recommend that you perform all procedures in this chapter only at
an ESD workstation. If one is not available, provide some ESD protection by wearing an antistatic
wrist strap attached to chassis ground (any unpainted metal surface on the server) when handling
parts.
ESD and handling boards: Always handle boards carefully. They can be extremely
sensitive to electrostatic discharge (ESD). Hold boards only by their edges. After removing a
board from its protective wrapper or from the system, place the board component side up on a
grounded, static free surface. Use a conductive foam pad if available but not the board wrapper.
Do not slide board over any surface.
Installing or removing jumpers: A jumper is a small plastic encased conductor that slips
over two jumper pins. Some jumpers have a small tab on top that can be gripped with ngertips
or with a pair of ne needle nosed pliers. If the jumpers do not have such a tab, take care when
using needle nosed pliers to remove or install a jumper; grip the narrow sides of the jumper with
the pliers, never the wide sides. Gripping the wide sides can dam-age the contacts inside the
jumper, causing intermittent problems with the function con-trolled by that jumper. Take care to
grip with, but not squeeze, the pliers or other tool used to remove a jumper, or the pins on the
board may bend or break.

- 6 -
Table of Contents
Chapter 1 Hardware Installation .....................................................................................9
1-1 Installation Precautions.................................................................................... 9
1-2 Product Specications.................................................................................... 10
1-3 System Block Diagram................................................................................... 14
Chapter 2 System Appearance.....................................................................................15
2-1 Front View...................................................................................................... 15
2-2 Internal HDD Cage View................................................................................ 15
2-3 Rear View....................................................................................................... 16
2-4 Front Panel LEDs and Buttons....................................................................... 17
2-5 RoT LEDs....................................................................................................... 19
2-6 Rear System LAN LEDs................................................................................. 21
2-7 Power Supply Unit LED.................................................................................. 22
2-8 Hard Disk Drive LEDs .................................................................................... 23
Chapter 3 System Hardware Installation ......................................................................25
3-1 Removing and Installing the Chassis Cover .................................................. 26
3-2 Removing and Installing the Heat Sink .......................................................... 27
3-3 Removing and Installing the CPU .................................................................. 28
3-4 Removing and Installing Memory................................................................... 30
3-4-1 Eight-Channel Memory Conguration ....................................................................30
3-4-2 Removing and Installing the Memory Module ........................................................31
3-4-3 Processor and Memory Module Matrix Table .........................................................31
3-4-4 Memory Population Table .......................................................................................32
3-5 Removing Hard Drive Cage ........................................................................... 33
3-6 Removing and Installing the PCIe/Riser Card................................................ 35
3-7 Installing the Mezzanine Card........................................................................ 37
3-7-1 Installing the OCP 3.0 Mezzanine Card .................................................................37
3-7-2 Installing the OCP 2.0 Mezzanine Card .................................................................38
3-8 Removing and Installing the Hard Disk Drive................................................. 39
3-9 Replacing the Fan Assembly.......................................................................... 41
3-10 Removing and Installing the Power Supply.................................................... 42
3-11 Cable Routing ................................................................................................ 43
Chapter 4 Motherboard Components ...........................................................................53
4-1 Motherboard Components ............................................................................. 53
4-2 Jumper Settings ............................................................................................. 55

- 7 -
Chapter 5 BIOS Setup ..................................................................................................56
5-1 The Main Menu .............................................................................................. 58
5-2 Advanced Menu ............................................................................................. 61
5-2-1 Trusted Computing .................................................................................................63
5-2-2 PSP Firmware Versions..........................................................................................64
5-2-3 Legacy Video Select...............................................................................................65
5-2-4 AST2500 Super IO Conguration...........................................................................66
5-2-5 S5 RTC Wake Settings...........................................................................................68
5-2-6 Serial Port Console Redirection .............................................................................69
5-2-7 CPU Conguration..................................................................................................73
5-2-8 PCI Subsystem Settings.........................................................................................74
5-2-9 USB Conguration..................................................................................................76
5-2-10 Network Stack Conguration..................................................................................78
5-2-11 NVMe Conguration ...............................................................................................79
5-2-12 SATA Conguration.................................................................................................80
5-2-13 UEFI POST LOGO Conguration...........................................................................81
5-2-14 AMD Mem Conguration Status.............................................................................82
5-2-15 T1s Auth Conguration ...........................................................................................83
5-2-16 Intel(R) I350 Gigabit Network Connection ..............................................................84
5-2-17 VLAN Conguration................................................................................................86
5-2-18 MAC IPv4 Network Conguration...........................................................................88
5-2-19 MAC IPv6 Network Conguration...........................................................................89
5-3 AMD CBS Menu............................................................................................. 91
5-3-1 CPU Common Options...........................................................................................92
5-3-2 DF Common Options..............................................................................................98
5-3-3 UMC Common Options ........................................................................................103
5-3-4 NBIO Common Options........................................................................................118
5-3-5 FCH Common Options .........................................................................................124
5-3-6 NTB Common Options .........................................................................................128
5-3-7 SOC Miscellaneous Control .................................................................................129
5-3-8 Workload Tuning...................................................................................................130
5-4 AMD PBS Menu........................................................................................... 131
5-4-1 RAS ......................................................................................................................132
5-5 Chipset Setup Menu..................................................................................... 134
5-5-1 North Bridge .........................................................................................................135
5-5-2 Fabric Resource ...................................................................................................136
5-6 Server Management Menu........................................................................... 137
5-6-1 System Event Log ................................................................................................139
5-6-2 View FRU Information ..........................................................................................140
5-6-3 BMC Network Conguration .................................................................................141
5-6-4 IPv6 BMC Network Conguration.........................................................................142

- 8 -
5-7 Security Menu .............................................................................................. 143
5-7-1 Secure Boot .........................................................................................................144
5-8 Boot Menu.................................................................................................... 146
5-9 Save & Exit Menu......................................................................................... 148
5-10 BIOS POST Beep code (AMI standard)....................................................... 149
5-10-1 PEI Beep Codes ...................................................................................................149
5-10-2 DXE Beep Codes .................................................................................................149

- 9 - Hardware Installation
1-1 Installation Precautions
The motherboard/system contain numerous delicate electronic circuits and components which
can become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully
read the service guide and follow these procedures:
• Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or
warranty sticker provided by your dealer. These stickers are required for warranty validation.
• Always remove the AC power by unplugging the power cord from the power outlet before
installing or removing the motherboard or other hardware components.
• When connecting hardware components to the internal connectors on the motherboard,
make sure they are connected tightly and securely.
• When handling the motherboard, avoid touching any metal leads or connectors.
• It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic
components such as a motherboard, CPU or memory. If you do not have an ESD wrist
strap, keep your hands dry and rst touch a metal object to eliminate static electricity.
• Prior to installing the motherboard, please have it on top of an antistatic pad or within an
electrostatic shielding container.
• Before unplugging the power supply cable from the motherboard, make sure the power
supply has been turned off.
• Before turning on the power, make sure the power supply voltage has been set according to
the local voltage standard.
• Before using the product, please verify that all cables and power connectors of your
hardware components are connected.
• To prevent damage to the motherboard, do not allow screws to come in contact with the
motherboard circuit or its components.
• Make sure there are no leftover screws or metal components placed on the motherboard or
within the computer casing.
• Do not place the computer system on an uneven surface .
• Do not place the computer system in a high-temperature environment.
• Turning on the computer power during the installation process can lead to damage to
system components as well as physical harm to the user.
• If you are uncertain about any installation steps or have a problem related to the use of the
product, please consult a certied computer technician.
Chapter 1 Hardware Installation

Hardware Installation - 10 -
1-2 Product Specications
System
Dimension
2U
438 (W) x 87 (H) x 730 (D) mm
CPU AMD EPYC™ 7003 series processor family
Single processor, 7nm technology
Up to 64-core, 128 threads per processor
cTDP up to 240W
Compatible with AMD EPYC™ 7002 series processor family
Chipset System on Chip
Hardware-
Level Root of
Trust Support
Supported
NOTE! The system will take extra time to boot as it goes through RoT
authentication.
Memory 16 x DIMM slots
DDR4 memory supported only
8-Channel memory architecture
RDIMM modules up to 128GB supported
LRDIMM modules up to 128GB supported
Memory speed: Up to 3200*/ 2933 MHz
Note:
* Follow BIOS setting and memory QVL list if running 3200 Mhz with 2DPC
LAN 2 x 1GbE LAN ports (1 x Intel® I350-AM2)
1 x 10/100/1000 management LAN
Video Integrated in Aspeed® AST2500
2D Video Graphic Adapter with PCIe bus interface
1920x1200@60Hz 32bpp
NOTE:
We reserve the right to make any changes to the product specications and product-related
information without prior notice.

- 11 - Hardware Installation
Expansion Slot Riser Card CRS101E:
- 1 x PCIe x16 slot (Gen4 x16), Full height half-length
Riser Card CRS101E:
- 1 x PCIe x16 slot (Gen4 x8 or x16), shared with OCP 2.0, Full height half-
length ( Please see NOTE below)
1 x OCP 3.0 mezzanine slot with PCIe Gen4 x16 bandwidth
1 x OCP 2.0 mezzanine slot with PCIe Gen3 x0 or x8 bandwidth, shared with
CRS101E ( Please see NOTE below)
NOTE:
1. GIGABYTE offers an optional riser card to support full bandwidth
PCIe Gen4 x16 and OCP 2.0 Gen3 x8
2. Contact GIGABYTE sales rep or technical support for more details about
supporting full bandwidth
Storage ront side: 24 x 2.5" SATA/ SAS hot-swappable SSD bays
Rear side: 8 x 2.5" SATA/ SAS, 2 x 2.5" U.2 hot-swappable SSD bays
Internal: 8 x 2.5" SATA/ SAS hot-swappable SSD bays
SAS card is required to enable the drive bays
• Broadcom SAS35x48 expander
• Bandwidth: SATAIII 6Gb/s or SAS 12Gb/s per port
• Default conguration supports:
• 0 x SATA/ SAS, 2 x U.2 drives
Suggested 12Gb/s SAS cards:
• CRA4648
• CSA4648
1 x M.2 slot:
- M-key
- PCIe Gen4 x4
- Supports NGFF-2280/22110 cards

Hardware Installation - 12 -
Internal I/O 1 x M.2 slot
1 x USB 3.0 header
1 x COM header
1 x TPM header
1 x OCP 3.0 mezzanine slot
1 x OCP 2.0 mezzanine slot
1 x Front panel header
1 x HDD back plane board header
1 x PMBus connector
1 x IPMB connector
1 x Clear CMOS jumper
1 x BIOS recovery jumper
Front I/O 2 x USB 3.0
1 x Power button with LED
1 x ID button with LED
1 x NMI button
1 x Reset button
2 x LAN activity LEDs
1 x HDD activity LED
1 x System status LED
Rear I/O 2 x USB 3.0
1 x VGA
2 x RJ45
1 x MLAN
1 x ID button with LED
Backplane I/O Front side_CBP20O8: 24 x SATA/SAS ports
Rear side_CBP10A5: 8 x SATA/SAS, 2 x U.2 ports
Internal_CBP2080: 8 x SATA/SAS ports
Speed and bandwidth:
SAS 12Gb/s, SATA 6Gb/s, and PCIe Gen4 x4
TPM 1 x TPM header with SPI interface
Optional TPM2.0 kit: CTM010

- 13 - Hardware Installation
System
Management
Aspeed® AST2500 management controller
GIGABYTE Management Console (AMI MegaRAC SP-X) web interface
Dashboard
JAVA Based Serial Over LAN
HTML5 KVM
Sensor Monitor (Voltage, RPM, Temperature, CPU Status …etc.)
Sensor Reading History Data
FRU Information
SEL Log in Linear Storage / Circular Storage Policy
Hardware Inventory
Fan Prole
System Firewall
Power Consumption
Power Control
LDAP / AD / RADIUS Support
Backup & Restore Conguration
Remote BIOS/BMC/CPLD Update
Event Log Filter
User Management
Media Redirection Settings
PAM Order Settings
SSL Settings
Power Supply 2 x 1200W redundant PSUs
80 PLUS Platinum
AC Input:
- 100-240V~/ 12-7A, 50-60Hz
DC Input:
- 240Vdc/ 6A
DC Output:
- Max 1000W/ 100-240V~
+12V/ 80.5A
+12Vsb/ 3A
- Max 1200W/ 200-240V~ or 240Vdc input
+12V/ 97A
+12Vsb/ 3A
Operating
Properties Operating temperature: 10°C to 35°C
Operating humidity: 8% to 80% (non-condensing)
Non-operating temperature: -40°C to 60°C
Non-operating humidity: 20% to 95% (non-condensing)

- 14 - Hardware Installation
1-3 System Block Diagram

- 15 - System Appearance
Chapter 2 System Appearance
2-1 Front View
No. Description
1. Front Panel LEDs and Buttons
2. USB 3.0 Port x 2
• Refer to section 2-4 Front Panel LEDs and Buttons for a detailed description of the
function of the LEDs.
1 2
HDD0 HDD1 HDD2 HDD3 HDD4 HDD5 HDD6 HDD7 HDD8 HDD9 HDD10 HDD11 HDD12 HDD13 HDD14 HDD15 HDD16 HDD17 HDD18 HDD19 HDD20 HDD21 HDD22 HDD23
2-2 Internal HDD Cage View
INTERNAL HDD0
INTERNAL HDD1
INTERNAL HDD2
INTERNAL HDD3
INTERNAL HDD4
INTERNAL HDD5
INTERNAL HDD6
INTERNAL HDD7
System Front Side System Rear Side

System Appearance - 16 -
2-3 Rear View
No. Description
1. Mezzanine Slot (Option/OCP 3.0 Card/SFF Type)
2. ID Button with LED
3. Server Management LAN Port
4. 1GbE LAN Port x 2
5. USB 3.0 Port x 2
6. Mezzanine Slot (Option/OCP 2.0 Card)
7. VGA Port
8. Low-Prole PCIe Card Slot
9. Low-Prole PCIe Card Slot
NOTE! The Green Latch Supports NVMe
• Refer to section 2-6 Rear System LAN LEDs for a detailed description of the function of the
LEDs.
7
8 9
2
31456
REAR HDD0
REAR HDD1
REAR HDD2
REAR HDD3
REAR HDD4
REAR HDD5
REAR HDD6
REAR HDD7
REAR HDD8
REAR HDD9
PSU1
(Primary)
PSU2
(Secondary)

- 17 - System Appearance
2-4 Front Panel LEDs and Buttons
L1 L2
1
3
5
7
2
4
6
8
(Note) If your server features RoT function, please see the following section for detail LED behavior.
No. Name Color Status Description
1. Reset Button Press the button to reset the system.
2. NMI button
Press the button server generates a NMI to the processor
if the multiple-bit ECC errors occur, which effectively halt
the server.
3. Power button
with LED
Green On System is powered on
Green Blink System is in ACPI S1 state (sleep mode)
N/A Off
• System is not powered on or in ACPI S5 state
(power off)
• System is in ACPI S4 state (hibernate mode)
4. ID Button(Note) Press the button to activate system identication
5. HDD Status
LED
Green On HDD locate
Blink HDD access
Amber On HDD fault
Green/
Amber Blink HDD rebuilding
N/A Off No HDD access or no HDD fault.

System Appearance - 18 -
No. Name Color Status Description
6.
System
Status
LED(Note)
Green Solid On System is operating normally.
Amber
Solid On
Critical condition, may indicate:
System fan failure
System temperature
Blink
Non-critical condition, may indicate:
Redundant power module failure
Temperature and voltage issue
Chassis intrusion
N/A Off
System is not ready, may indicate:
POST error
NMI error
Processor or terminator missing
7/8.
LAN 1/2
Active/Link
LEDs
Green Solid On Link between system and network or no access.
Green Blink Data trasmission or receiving is occuring
N/A Off No data transmission or receiving is occuring
(Note) If your server features RoT function, please see the following section for detail LED behavior.

- 19 - System Appearance
LED on Front panel(Note5)
ID LED Status LED
EC Firmware (FW) Authentication fail or not exit
EC FW is broken or not exit (Note1) OFF OFF
Authenticating/Recovering BMC/BIOS Images
Authenticating Images OFF OFF
Recovering BMC Active Flash
Blinks Blue
4 times per
second
Blinks Green
4 times per
second
Recovering BIOS Active Flash
Blinks Blue
4 times per
second
Blinks Green
4 times per
second
Authentication (AUTH) Pass
Recovering BIOS Active Flash OFF OFF
BMC : AUTH pass after doing recovery
BIOS : AUTH pass after doing recovery OFF OFF
BMC : AUTH pass after doing recovery
BIOS : AUTH pass OFF OFF
BMC : AUTH pass
BIOS : AUTH pass after doing recovery OFF OFF
2-5 RoT LEDs
L1 L2
Status LE
D
ID LED

System Appearance - 20 -
Active Flash Authentication (AUTH) Fail
BMC : AUTH Fail(Note2)
Blinks Blue
1 time per
second
Blinks Green
1 time per second
BIOS : AUTH fail(Note2)
Blinks Blue
1 time per
second
Blinks Amber
1 time per second
BMC : AUTH fail after doing recovery(Note3)
Blinks Blue
2 times per
second
[ON OFF OFF]
Blinks Green
2 times per
second
[ON OFF OFF]
BIOS : AUTH fail after doing recovery(Note3)
Blinks Blue
2 times per
second
[ON OFF OFF]
Blinks Amber
2 times per
second
[ON OFF OFF]
Backup Flash Authentication Fail(Note4)
BMC : AUTH fail
Blinks Blue
2 times per
second
[ON OFF
ON OFF]
Blinks Green
2 times per
second
[ON OFF
ON OFF]
BIOS : AUTH fail
Blinks Blue
2 times per
second
[ON OFF
ON OFF]
Blinks Amber
2 times per
second
[ON OFF
ON OFF]
NOTE!
1. EC FW is broken or not exited result in Microchip CEC1702 cannot load EC FW for authentication.
2 (1) Authentication fail include below scenarios
Conguration table is missing or modied
Public key is missing or modied
Protected area or signature is modied
Flash empty
3. if active ash is still authentication failed after recovery sequence, Microchip CEC1702 stop the process
and showing LED behavior.
4. If backup flash authentication is failed cause by configuration table, public key or protected area is
broken. Microchip CEC1702 stop the process and showing LED behavior.
5. Front panel LED is controlled by BMC or Microchip CEC1702. Once Microchip CEC1702 is working(Auth
or recovery), the front panel LED is controlled by Microchip CEC1702 and vice versa.