Gimoto RR V-Race Hybrid Technology User manual

SYSTEM COMPONENTS
PARTS AND CONNECTIONS

THE VIRTUAL CABLE SYSTEM CONSISTS OF 3 DEVICES
THE CPU.
The brain of the system
THE ANTENNA ON THE VEST.
Called “VEST TAG”
THE ANTENNA ON THE BIKE.
Called “ANCHOR”
Anchoring to give exactly the concept of VIRTUAL CABLE fixing

PARTS & CONNECTIONS
VEST CONNECTOR
Connect CPU to TAG
If not inserted the system cannot
work properly (CPU “Blinks” Purple)
ACTUATOR CONNECTOR
Connect actuator, if not connected
system cannot inflate the vest

PARTS & CONNECTIONS
DISCONNECT WHEN
REST FOR LONG TIME
Disconnect if not going to use the vest
for long time, it may drain the battery
TURN CPU OFF
BEFORE CONNECT/DISCONNECT
TAG may be damaged if CPU is on, then
the system cannot operate properly
(CPU “Blinks” Purple)

V-RACE RR CPU
CPU LED
CPU SWITCH
(ON IS RIGHT SIDE)
CHARGER PORT

V-RACE RR CPU
V-RACE RR CPU
CPU needs to be charged at
least 6/8 hours before use,
using the USB charger sup-
plied in the box, and needs to
be charged each time cpu led
turns RED
Li-Ion accumulator requires
3 cycles to reach maximum
level of power

V-RACE RR BIKE ANCHOR
V-RACE RR BIKE ANCHOR
Anchor needs to be charged at leat 6h before use
using the USB charger supplied in the box, then
charge will last 24/30h.
Li-Ion accumulator requires 3 cycles to reach maxi-
mum level of power.
The ANCHOR system does not have a switch on/off
button. Once loaded, the system remains in charge
for 25/30 hours maximum.
ATTENTION: the system LEDs remain lit for the
entire charging time.
It is suggested to RECHARGE the system just before
the actual use OR to connect it permanently to the
motorcycle battery, under lock and key.
DO NOT USE THE SYSTEM
IF ANCHOR LEDS ARE OFF

V-RACE RR BIKE ANCHOR
POSITION
Anchor best positioning
At back of rider, in sight.
Inside tail installation allowed,
please check distance via App
to check anchor is seen in
action range (<1m)

V-RACE RR BIKE ANCHOR
DETECTION
Vest detect automatically all
anchors in range (up to 6 MT)
but it “choose” the nearest one
MOTORBIKE A
nearest anchor
farest anchor
MOTORBIKE B

V-RACE RR BIKE ANCHOR
ANCHOR BINDING
Vest automatically bind the anchor as soon
as bike starts.
So there’s no need to do any manual bin-
ding, neither changing anchor. The rider
can switch on another bike with a different
anchor and the CPU read it automatically.
The SYSTEM is ARMED , is ready to inflate
the AIRBAG, when the BIKE reaches the
minimum speed levels.
These minimum SPEED LEVELS ( street or
racetrack mode ) are chosen through the
VraceRR APP in the setting page.

V-RACE RR CPU - LED DIAGNOSTIC
STARTUP CYCLE (WHEN TURNED ON)
CHECK CPU CONNECTOR
SYSTEM NOT WORKING
PROPERLY
INITIALIZAZION STARTED (SYSTEM CHECK)
(SOLID YELLOW)
CHECK ENDS
STREET MODE
(FLASHING LIGHT BLUE)
RACETRACK MODE
(FLASHING WHITE)
SYSTEM OK
(FLASHING YELLOW)
NO TAG DETECTED
(FLASHING PURPLE)
DO NOT USE THE SYSTEM
IF LED TURN RED

V-RACE RR CPU - LED DIAGNOSTIC
OTHER LED MESSAGES
BATTERY NEED TO BE CHARCED
(SOLID RED)
ANCHOR DETECTED
(FLASHING ICE BLUE)
SYSTEM ACTIVATED
(SOLID PURPLE)
GPS SIGNAL LOCKED
(FLASHING GREEN)
SYSTEM ARMED
(FLASHING BLUE)
DO NOT USE THE SYSTEM
IF LED TURN RED

V-RACE RR CPU - APP
The V-RACE RR APP
is just an “Instant Diagnostic” for:
Battery Level of the CPU
Selection of the RIDING MODE
(STREET or RACETRACK mode)
RESET the CPU after an inflation.
App is used only for a “Instant Diagnostic” of
the CPU. The pairing must be reconnected each
time you need another “Instant Diagnostic”
THE SYSTEM WORKS WITHOUT THE APP. WHEN
THE CPU AND THE ANCHOR ARE SWITCHED ON,
THE SYSTEM WORKS AUTOMATICALLY

V-RACE RR CPU - APP PAIRING
CPU SERIAL AND PAIRING PASSWORD
Procedure is slightly different depending on your device
OS (Android or Apple iOS) and version of OS
Some devices using proprietary implementation of Bluetooth
may not be compatible. You can find the CPU in the Bluetooth
panel on your mobile.
Turn on Bluetooth for
pairing the airbag CPU
and seach the device
VRACERR******
INSERT PIN CODE
VRACE RR
HW: R04.00
SN: 00328
PIN: 123456

V-RACE RR CPU - APP PAIRING
COMMON ISSUES
On Android devices using BLE requires
GPS position ON
On Android 10, the application itself
needs to be authorized
On some Android devices, pairing is a
bit tricky with paring
authorization request hidden in notifi-
cation area

V-RACE RR CPU - APP PAIRING
COMMON ISSUES
Only one device per time can be paired and
connected, once connected the cpu may not be
seen from other smartphones
Once set desired mode (Track or Street) the
app is totally optional, the system will work
without any connection to a smartphone
Be a bit patient: connection requires some se-
conds, and entering connection menu the app
will try to connect last connected CPU automa-
tically. You can still connect any CPU in range
via Connection menu dropdown list

HELP LINKS
TUTORIAL AIRBAG STRETCH KIT
ELECTRONIC RECHARGE MECHANIC RECHARGE
ELECTRONIC MANUAL MECHANIC MANUAL
LED DIAGNOSTIC CATALOGUE