TECH SHEETTECH SHEET
TE
ECH SHETTE
ECH SHET
T ET
ECH SHE
T ET
ECH SHE
TECH SHEETTECH SHEET
TECH SH ET
E
TECH SH ET
E
TECH SHEET
TECH SHEET
TECH SHEET
TECH SHEET
TECH SHEET
TECH SHEET
TE
ECH SHE TTE
ECH SHE T
TH S ET
EC HETH S ET
EC HE
TECH S ET
HETECH S ET
HE
T S ET
ECHHET S ET
ECHHE
T H S ETEC HET H S ETEC HE
TECH SHEET
TECH SHEET
TECH SHEET
TECH SHEET
TECH S ETHE
TECH S ETHE
TE H SHEE
CTTE H SHEE
CT
H
TECH S EET
H
TECH S EET
HEE
TECH S T
HEE
TECH S T
TECH SHEETTECH SHEET
E H HEE
T C S T
E H HEE
T C S T
TE H SHEE
CTTE H SHEE
CT
TECH SHEETTECH SHEET
E H HEE
T C S T
E H HEE
T C S T
H
TECH SEET
H
TECH SEET
HEE
TECH ST
HEE
TECH ST
E H HEE
T C ST
E H HEE
T C ST
HEE
TECH S T
HEE
TECH S T
HEE
TECH ST
HEE
TECH ST
E H HEE
T C S T
E H HEE
T C S T
TE H SHEE
C T
TE H SHEE
C T
EHHEE
T C ST
EHHEE
T C ST
3611 3 Mile Rd. N.W. Grand Rapids, MI. 49544-1231 Fax (616) 791-9925
TECHNICAL SHEET 877-785-1897
T/G-401 PRELIMINARY 11/03
9. Insert 15 samples of the first coin.
During programming, the sample coins
will be returned through the "reject slot".
After 15 coins have been inserted
light will turn off. In quick succession,
press PROGRAM button once for
every output pulse desired for that coin.
Before Programming:
1. Select 15 samples of each different
coin type to be accepted. Use a
variety of years & mints to create
an accurate representation of each coin.
2. The lowest denomination of coins to be
accepted will be the base value of all the
others & will equal one output pulse for
the Multitron.
Example: quarters(base) = $0.25 = 1 pulse
dollar coin = $1.00 = 4 pulses
3. To make future changes in coins to be
accepted or coin value, the entire
programming procedure must be
repeated.
4. The Multitron is designed to accept up to 4
different coins.
Outputs for all coins are sent via the
Red/Green and Red/Yellow wires.
Red/Green
Wire
Programming Instructions:
6. Apply power
to the Multitron
and wait
3 minutes
for the unit
to stabilize.
The output pulses are sent as follows:
5. Once programmed, the Multitron will hold
its program even when power is removed.
NOTE: The Multitron must be installed in the equipment
being used to ensure proper programming.
NOTE: Nickle alloy tokens and U.S. nickels CANNOT be
programmed in the Multitron.
7. Press PROGRAM button.
Release button when light
turns on.
8. Press PROGRAM button once for
each type of coin to be programmed.
If you desire to accept four different
coins, press PROGRAM button 4
times, If 2 different coins, press button
2 times, etc.
Wait 4 seconds for light to blink.
Light remains on.
Credit
Sensor
Program
Button
Program
Light
P
O
W
E
R
x 15
10. The light will automatically
come back on after the value has
been programmed. When light
turns on, repeat step 9 for the next
type of coin to be accepted.
1st Coin
Type
2nd Coin
Type
3rd Coin
Type
4th Coin
Type
Coin/Token
Record Coin Information for future reference:
Pulses SensitivityBase
1
2
3
4
11. When the last coin has been
programmed (set in step 8) the
Multitron is ready to accept coins.
Light will remain off.
NOTE: After the last coin is programmed, the light will remain off. Only the amount of coins entered in step 8 can be
programmed and if any error is made you must start the entire process over. This is done by either finishing the process and
returning to step 7 or removing power during programming causing Multitron to return to its previous program.
Page 1 of 2
Programming Instructions for GS-44 Multitron Coin Acceptor
For AFTER Serial Number 8665
