Gispen IC HVE Series User manual

Gispen - www.gispen.com - All rights reserved - version 07/15
工具
根据尺寸，螺丝的数量可能会有变化
Tools
=
*Depending on the dimensions, there may be more / less screws
M8x12
(4x)
M8x10
(17x)
M8
(1x)
M6x10 or
4.8x16
(32x)
Nr. 2
Nr. 5
Gispen IC SINGLE WORKSTATION
Gispen IC
Installation manual
安装指南
单独工作区
HVE- 单独

Gispen - www.gispen.com - All rights reserved - version 07/15
HVE- 单独
将框架旋转180°
安放桌脚 用凹头螺丝固定桌脚
把框架安放于软表面上
Turn the frame 180 degrees
Fasten the table legs using the socket-head
screws
Insert the axis into the frame at the back
Place the table legs
Place the frame on a soft surface
5
4
6
3
21
Nr. 5
M8x10
(16x)
在背面，将轴插入到框架内

Gispen - www.gispen.com - All rights reserved - version 07/15
HVE- 单独
轴与绿色或蓝色边的左侧连接。
将短轴推到右桌腿上将长轴推到左桌腿上
Fasten the long axis and short axis
Push the axis through the axis connection
Loosen 1 socket-head screw from the frame
Place the axis connection with the green or blue
side to the left
Push the short axis onto the right table legPush the long axis onto the left table leg
11
10
12
9
87
Nr. 5
通过轴连接推送轴
固定长轴和短轴
Nr. 2
从框架上松开1个凹头螺丝

Gispen - www.gispen.com - All rights reserved - version 07/15
HVE- 单独
用螺丝将框架固定在桌面上
使用2个凹头螺丝和1和螺母固定电动机 将框架旋转180°，然后将框架放在桌面上
安放电动机
Fasten the frame to the tabletop using the screws
Turn the frame 180 degrees and place it onto the
tabletop
Positions of the screws
Fasten the motor using 2 socket head screws and
1 nut
Place the motor
17
16
18
15
1413
M6x10 or
4.8x16
(24x)
Nr. 5
M8x10
(2x)
M8 (1x)
螺丝的位置

Gispen - www.gispen.com - All rights reserved - version 07/15
HVE- 单独
插入电缆槽连接件
插入电缆槽连接件
用螺丝固定电缆槽安装板
Insert the cable tray connections22
21 Insert the cable tray connections
Fasten the cable tray mounting plates using the
screws
20Fasten the motor using the screws19
M6x10 or
4.8x16
(8x)
M6x10 or
4.8x16
(2x)
使用螺丝将电动机固定

Gispen - www.gispen.com - All rights reserved - version 07/15
HVE- 单独
将桌子旋转180°
把电缆槽安装到桌子上
24 Turn the table 180 degrees
23 Mount the cable tray onto the table
Adjust the height of the table legs25
将按钮连接安放按钮
Connect the push buttons2726 Place the push buttons
调整桌脚高度

Gispen - www.gispen.com - All rights reserved - version 07/15
HVE- 单独
从框架上松开4个凹头螺丝
用凹头螺丝固定主机架
调整桌脚高度
Loosen 4 socket-head screws from the frame
Fasten the CPU holder using the socket-head screws
31
32
30 Adjust the height of the table
Nr. 5
Nr. 5
M8x12
(4x)
30 sec./秒
重置电子部件
2928 Reset the electronic parts Connect the table to the mains
OR
或
将桌子连接到电源

Gispen - www.gispen.com - All rights reserved - version 07/15
HVE- 单独
把电脑安装到主机架上
33 Mount a computer onto the CPU holder