GL-INET Collie Installation instructions

or
Set up Router
Visit http://192.168.8.1 in your browser
to set up your router; start by choosing
your preferred language.
Insert Cards & Power On
When powered up, your router will broadcast a
Wi-Fi signal with the SSID: GL-X300B-xxx.
Hot plug for standard SIM card
is not supported for this router.
Default password is goodlife
Search the SSID and connect to it
Connect to the 2GHz Wi-Fi called
GL-X300B-xxx, and input the default Wi-Fi
password goodlife, which is also printed on
the bottom of the router.
Connect via Wi-Fi
SETTING UP
Plug the cable connecting
to your computer into LAN port
Connect via LAN
Let’s get
started.
Collie / GL-X300B
Industrial 4G LTE Gateway
Standard SIM Card
(Optional)

SUPPORT WARRANTY
We provide one year limited warranty for routers and 3-month limited warranty for accessories.
Extra warranty may apply according to the local law in which the product purchase took place.
Highly recommend using the included 12V/1A power adapter.
Any damage to the router caused by not following the instructions will render this warranty null
and void.
Any damage to the router caused by modifying the PCBA, components or case will render this
warranty null and void.
Issues caused by the use of third-party firmware may not get official support from us.
Any damage to the router caused by inappropriate use, e.g. inappropriate voltage input, high
temperature, dropping in the water or on the ground will render this warranty null and void.
Pictures on the instructions are only for reference. We reserve the right to change or modify
these materials without further notice.
This product uses WiFi 2.4GHz Operating Frequency is 2400~2483.5MHz;
The Product comply with Directive 2011/65/EU and its amendment directive 2015/863/EU (Rohs2.0)
The Equipment named above is confirmed to comply with the requirements setout in the European Council Directive on the Approximation of the
Laws of the Member States relating to RED (2014/53/EU). The equipment passed the test which was performed according to the following
European standards:
EN 301 489-1 V2.2.3; EN 301 489-3 V2.1.1；EN 301 489-17 V3.2.2; EN 301 489-52 V1.1.0; EN 300 328 V2.2.2 ; EN 301 511 V12.5.1;
EN 301 908-1 V13.1.1; EN 301 908-2 V11.1.2; EN 301 908-13 V11.1.2;
EN 62311:2008
EN62368-1:2014+A11:2017
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
3. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help important announcement.
FCC ID:2AFIW-X300B
GL Technologies (Hong Kong) Limited
Unit 203, 2/F, Building 19W, 19 Science Park West Avenue,
Hong Kong Science Park, Pak Shek Kok, N.T., Hong Kong
Hong Kong Office
Shenzhen Guanglianzhitong Tech Co., Ltd.
Room 305 - 306, Skyworth Digital Building, Shiyan Street,
Baoan District, Shenzhen, China, 518000
( [phone] )
Shenzhen Office
ver. 20201215
Technical Supports
For more detailed and updated instructions, please visit our website docs.gl-inet.com
For further questions, you can get help from the following ways:
- Email to [email protected]
- Message us on our Facebook: facebook.com/gl.inet.wifi/
- Post questions in our forum: forum.gl-inet.com
- Ask professionals in other forums e.g. OpenWrt, LEDE or other professional websites
https://docs.gl-inet.com/en/3/
Repair / Reset
If you cannot access the web-based setup page or cannot connect to the
router, you can press the Reset button:
Press and hold for 3 seconds, and then release to repair your network.
Press and hold for 10 seconds, and then release to reset the router
to factory settings. All user data will be cleared.
Standard SIM card slot
Reset button
Power port
DC9-35V
PUSH
SIM
LAN
WAN
LAN Ethernet port
RS485 Connector
WAN Ethernet port
4G
WiFi
WAN
Power
Lights:
PWR 4G
DC
9-35V
B A GND
WIFI WAN