Glendinning CRMA 16 User manual

CRMA Technical Manual Rev. 4.0
CRMA 30
Table of Contents
1) Product Descripon
2) Product Dimensions
3) Installaon
4) Operang Instrucons
5) Maintenance
6) Troubleshoong
7) Accessories
1.0 PRODUCT DESCRIPTION
The CRMA Cordreel has been designed
for manual pay out and motorized retracon
of your shore power cable.
The Cordreel can store 30amp 125volt
shore power cable and European 16amp and
32amp 250volt shore power cable.
CRMA30-XX-YY
CRMA 16 / 32
CRMA16-XX-YY
CRMA32-XX-YY
XX – DC voltage
YY – length of cable
Waterproof switch and
nameplate assembly w/
10’ wires (all CRMA units)
16 and 32 amp
Pin and Sleeve
Twist lock plug
and lanyard
Anodized Aluminum
Frame
Yellow—16 or 32amp/250volt
15m or 25m Euro cable
White—30 amp/125 volt
50’ cable
Power Cord Retrieval & Storage System
INSTALLATION & OPERATION MANUAL
Glendinning Products, LLC. 740 Century Circle Conway, SC 29526 Phone: [phone] Fax: [phone]

2
2.0 PRODUCT DIMENSIONS
3.0 CORDREEL INSTALATION
3.1 Before You Start the Installaon
The most important part of your installaon is planning the best layout for the shore power cable roung from
the unit to where it exits the boat (normally through a Hawse Pipe). Be sure that cable is roung a straight path, free
from any obstacles. If the cable exit is not in line with the center of the reel, it is very possible the cable will wrap on
the side of the reel closest to the exit and could bind during retracon. There are some accessories you can purchase
to help if there is no way to center the exit to the Cordreel. (See secon 7 for accessories.) Also make sure that
Cordreel is installed in a place where it is protected from the environment.
CRMA 16/30/32

3
3.2 Installaon Conguraons
The Cordreel(16, 30, and 32) is capable of being mounted in mulple conguraons:
Overhead Mounng - standard Overhead Mounng - reverse
Guide Roller Assembly
can be moved from top
posion to boom
posion. Remove 4
bolts/spacers, move
assembly and re-install
including 4 spacers.
Deck Mounng – reverse
(similar to original CRM30 cong.)
Deck Mounng –standard
(as shipped conguraon)
Oponal Base Plate
Part# 60537. Mount
using 6 bolts.
Note: Baseplate is not
required for overhead
mounng.
3.3 Mounng Instrucons
• In general, the Cordreel will be mounted to either the oor or the overhead of the compartment where it will be
located.
• Allow clearance for the Cordreel storage spool to operate freely without obstrucon or interference, and for the
connecon of the power cable from your power supply.
• Install the Cordreel using 1/4” bolts, 1” long minimum. Bolt unit in each of the four corners. (See above for
bolng locaons. Look for )
• In general, the Cordreel will be mounted to either the oor or the overhead of the compartment where it will be
located.
NOTE: Unspooling the power cord before mounng the Cordreel can aid installaon in ght spaces.
NOTE: There is also an oponal baseplate that can be used for overhead mounng. (Use 6 bolts to mount baseplate.)

4
DC Power Input
(12v or 24v DC, check label on unit)
Red - DC Positive +
Black - DC Negative -
- use 15amp fuse/breaker
Power Switch Control Wire
- 10' long (3mtrs)
Connects into back of Rocker switch
AC Power Input
- 10' long 105c wire
DC Power Input
Red - DC Positive +
Black - DC Negative -
- use 5amp fuse/breaker
Wireless Remote
-Splice into the black wire at switch 1
2
3
4
DC
Wireless Remote Control
Part# 04154 12/24v Remote
Guide Roller In-Limit Switch Assembly
Part# 04862-X
Wireless Remote
Connection
-Splice into black wire
Switch Switch Wire to unit
Black
Red
Remote Antenna
- antenna must be mounted horizontally
and connected to the reciever for
proper operation of the remote.
Control Switch and
Nameplate
OPTIONAL
OPTIONAL
Installation:
- remove CRMA30 AC/motor cover
- select 12" long brown wire loop
- cut wire in half and splice into each
Out-Limit switch Assembly wire.
- replace CRMA30 cover
3.4 Wiring Diagram

5
3.5 Installing the Hawse Pipe (oponal accessory)
The installaon of the Hawse Pipe is oponal.
You may also use an exisng hatch or any storage
space door that is accessible to where you want the
power cord to exit.
• Before drilling or cung, be certain that the area
is free of wires, plumbing or structural supports.
• Mount Hawse Pipe.
• Make sure the roung between the Hawse Pipe
and the unit is free from obstrucons, such as
wire/tubing, etc.
3.6 Connect Reel to AC Panel
The “pigtail” that comes on the Cordreel must
be connected to the juncon box or power switch that
supplies 125v or 250v to the boats electrical system.
• Strip the insulaon from the end of the “pigtail” as
well as the green, white, and black wires within
the insulaon jacket.
• Aach appropriate connectors to each wire and
aach to the juncon box.
16/32amp 250v AC
30amp 125v AC
Brown—250 VAC
Blue—Neutral
Green—Ground
Black—Line 125 VAC
White—Neutral
Green—Ground
Part# 04049-CRM
Hawse Pipe Assembly
Hole cut out 3.75”
diameter Clearance hole 17/64
Holes 4” apart
WARNING:
• All wiring should be done in ac-
cordance with ABYC’s standards. If
you are unsure of these standards,
consult a qualied electrician.
• Failure to wire correctly may result
in DEATH, INJURY OR DAMAGE TO
PERSONS, VESSESL, OR UNIT. Ter-
minals are marked for correct wir-
ing: HIT, NEUTRAL, & GROUND.
!
!

6
3.7 DC Wire Connecon
WARNING:
• All wiring should be done in ac-
cordance with ABYC’s standards. If
you are unsure of these standards,
consult a qualied electrician.
!
!
3.8 Control Switch
• Mount the control switch near where the cable exits
the side of the boat.
• Connect red quick connector terminal to the tabs on
the control switch.
The Cordreel comes with (2) 14 gauge wires exing from
the gear motor cover.
• These wires should be connected to the 12 or 24
VDC power source depending on unit purchased
(see label on unit for correct voltage).
• Connect wire to DC baery as shown to le.
• Make sure all connecons are secured and protect-
ed from the environment.
DC Power Input
•12 or 24v DC Input (check
label on unit)
RED - DC Posive +
BLACK - DC Negave
•use 15amp breaker or fuse
10’ long Control
Switch Wires
Cutout for switch is
1” x 1.75”

7
4.0 OPERATING INSTRUCTIONS
To operate your Cordreel:
• PULL OUT only the amount of shore power cord required to reach the outside power source.
• CONNECT your shore power cord to outside power source receptacle.
• TURN ON outside power supply.
When ready to get underway:
• TURN OFF outside power supply.
• DISCONNECT cord from the outside power supply.
• PUSH AND HOLD the Cordreel power switch (black rocker
switch). Cordreel will electrically retrieve the power cord and
store.
• When cord is fully retracted, RELEASE the power switch to
stop the unit. NOTE: Not releasing the switch may cause the
plug to get jammed in the unit and make the next use dicult.
5.0 MAINTENANCE
• TO RELIEVE ANY KINKING that may happen Rounely extend the power cable completely, stretch it on any at sur-
face, and allow the Cordreel to retract the cable into the reel.
• INSPECT ALL AC AND DC WIRING CONNECTIONS and make sure they are free of corrosion and connecons are
ght.
• INSPECT THE EXTERIOR JACKET of the power cable for nicks or cuts.
• IF YOUR POWER CABLE IS DIRTY, any cleaner should be compable with the outer jacket material of the power
cable.
• IF NEEDING TO REPLACE POWER CORDSET, USE ONLY 105⁰c (CRMA-30/32) of 90⁰C (CRM-16) MINIMUM RATED
CORDSETS and ensure that the outside diameter of the new cordset does not exceed that of the factory supplied
cordset.
6.0 TROUBLESHOOTING
ISSUE PROBABLE CAUSE RECOMMENDED ACTION
Non-funconal (either no power
or unit has power and does not
respond)
Tripped breaker
Blown fuse at power source
Power wire incorrectly connected
to power source
Defecve motor
Reset breaker
Replace fuse
Check power source fuse and connecons,
reconnect or replace if necessary
With power switch on and voltage across motor
wires
Cordreel stops retracng
while buon is being pushed
Cord jammed during retracon
causing breaker to trip
Reset breaker
Pay out cable and rewind
! CAUTION:
• Always disconnect AND fully retract
your cable BEFORE geng underway!
• Connuing to push power buon
aer cable is retracted may cause
damage to the motor and will cause
breaker switch to trip - reset before
next use.

8Rev Date: 10/18
7.0 ACCESSORIES
PART# Descripon
04054 Guide Roller Assembly with Plate
04154 Remote Control System 12/24V, Includes (2) transmiers, (1) receiver, (1)
antenna, and (1) wire harness
04049-CRM Stainless Steel Hawsepipe
04079-CRM Hawse Pipe Assembly w/ Roller Assembly
04079-CRM-LS Hawse Pipe Assembly w/ Roller Assembly & In-Limit Switch
WARRANTY
PRODUCT COVERED BY THIS LIMITED WARRANTY: CRMA 16/30/32
1. GLENDINNING PRODUCTS, LLC. warrants to the original consumer purchaser that the CRMA 16/30/32 will be free from defects in material
and workmanship under normal use and service for a period of one (1) year from the date of purchase.
2. This LIMITED WARRANTY applies to defects in material and workmanship. It does not apply to plated or painted nishes or to cord damage
caused by inadequate cable storage area or installaon not in accordance with GLENDINNING PRODUCTS, LLC. specicaons.
3. This LIMITED WARRANTY is void if the product has been damaged by accident or unreasonable use, neglect, improper installaon, or other
causes not arising out of defects in material or workmanship.
4. To obtain performance of this LIMITED WARRANTY obligaon the original purchaser should contact GLENDINNING PRODUCTS, LLC. for
instrucons concerning removal and shipping of the defecve component. Upon compliance of the foregoing procedure all warranted defects
will be repaired, or at GLENDINNING PRODUCTS, LLC. opon, the complete unit replaced and returned to the consumer, shipping charges
prepaid.
5. GLENDINNING PRODUCTS, LLC. does not assume the costs of removal and/or installaon of the product or any other incidental costs
which may arise as a result of any defect in materials or workmanship.
THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES. ANY WARRANTY IMPLIED BY LAW INCLUDING WARRANTIES OF MERCHANT-
ABILITY OR FITNESS, IS IN EFFECT ONLY FOR THE DURATION OF THE EXPRESS WARRANTIES SET FORTH IN THE FIRST PARAGRAPH ABOVE. NO
REPRESENTATIVE OR PERSON IS AUTHORIZED TO GIVE ANY OTHER WARRANTY OR TO ASSUME FOR GLENDINNING PRODUCTS, LLC. ANY OTH-
ER LIABILITY IN CONNECTION WITH THE SALE OF IT’S PRODUCTS. GLENDINNING PRODUCTS, LLC. WILL NOT BE LIABLE FOR ANY CONSEQUEN-
TIAL DAMAGES RESULTING FROM THE USE OR INSTALLATION OF IT’S PRODUCTS.