Global Industrial FM180K User manual

Instruction Manual
FM180K FM270K
FM360K FM450K
NOTE: Owner/Operator must read and understand this
instruction manual before using the mover.

Contents
1. Description
2. Specifications
3. Precautions and Preparation
4. Operation
5. Care and Maintenance
6. Parts Lists & Exploded Figures

THANK YOU VERY MUCH FOR CHOOSING OUR HYDRAULIC
FURNITURE MOVER. FOR YOUR SAFETY AND CORRECT
OPERATION, PLEASE CAREFULLY READ THE MANUAL BEFORE
USE.
NOTE: All of the information reported herein is based on data
available at the time of printing. The factory reserves the right to
modify its own products at any time without notice or incurring in any
sanction. Please verify with the factory for possible updates.
1. Description
Equipment Mover are designed for use safe, easy lifting and
transportation of large, bulky loads. Each unit must use in pairs. And
each unit is equipped with fork, hydraulic jack, operation handle,
support frame and moving frame, casters, and all mounting hardware.
！
CAUTION
Never exceed the maximum capacity of the equipment mover.
1. Units must be connected with load binders before load is lifted.
2. Only intended for use in pairs.
3. Make sure load is centered on forks.
4. Never move the unit unless the forks are in the lower position.
5. Equipment Mover are intended for movement of loads and are
not intended for positioning loads in a raised position for extended
period of time.
6. Do not leave units unattached with load in raised position. Do not
use units on inclines.
7. The units are not designed to lift people. Do not stand on the load
and do not place any body part under the load at all times.
8. Inspect unit thoroughly, daily, before operating. Make sure that all
attachments and fasteners are completely tightened.
9. When units are not in use, they should be completely lowered

and release valve tightened.
10. Do not operate a damaged unit until it is completely repaired.
11. Always remove load before repairing.
12. Warning: units are unstable if handled improperly. Use caution
when moving over uneven floors.
2. Specifications
Model FM180K-1 FM180K-2 FM270K-1 FM270K-2
Capacity (lb.)
Lifting Height (mm)
Wheel Material PU+Steel All Steel PU+Steel All Steel
Wheel Size (mm)
Net Weight (lb.) 297 301.4 352 356.4
Model FM360K-1 FM360K-2 FM450K-1 FM450K-2
Capacity (lb.)
Lifting Height (mm)
Wheel Material PU+Steel All Steel PU+Steel All Steel
Wheel Size (mm)
Net Weight (lb.) 420.2 424.6 475.2 479.6
5940
7920
9900
3960
150
Φ150×65
Φ200×75
Φ150×50
150
3. Precautions and Preparation
3-1 The floor must be absolutely level, smooth and clean. There
must be no inclines or slopes to be moved over. Make sure that the
floor and the floor covering are to stand up to the loading imposed by
the wheel and whether they can take the weight of the furniture being
transported.
3-2 Check whether the piece of furniture to be transported contains
any loose objects. These will have to be removed, or secured against
slopping out of position.
3-3 Check whether the piece of furniture is strong enough for the
two opposite sides to take the weight of the piece via the transport
units' platforms, and whether the upper supports of the transport units

can hold the furniture to be transport without damaging it.
3-4 Find the weight of the piece of furniture to be transported. Never
exceed the maximum capacity of the equipment mover.
3-5 Find the center of gravity of the furniture to be transported.
Along the furniture base, it is the decisive for the load that a single
transport unit can bear, across the base, for the center of the transport
unit, and, in connection with the height, for the moment of tilting that
occurs when moving the furniture. When in use, the height of the
center of gravity must not exceed 0.8m. The distance of the transport
units to one another must not be less than 0.5m and not gravity 4.0m
(furniture of the securing straps).
3-6 Never use this equipment for towing behind a vehicle.
4. Operation
Units is ready to use as shipped, if hydraulic jack does not operate
properly, contact the dealer you purchased unit from immediately.
4-1 With one foot placed securely on padded bar and both hands
firmly gripping handle. Position forks of first unit under load. Make
sure load is centered on forks.
4-2 Fork (rubber) must be in contact with load.
4-3 Position second unit in same manner as above on other end of
load.
4-4 Connect the two units with load binders (available from dealer).
4-5 Two people are required for operating and moving loads.
To lift
(1) Pump up jack slowly on the pairs units simultaneously, raise load
off floor up to the height required, but Do not over the specified lift
height.
(2) Keep hands and feet clear of bottom of load and casters.
(3) Check placement of forks under load, Binders must be tight
before moving.

To lower
(1) Open jack release valve slowly on pair units simulatneously until
load rests on floor.
(2) Remove load binders.
(3) Carefully remove unit forks from under load. Lower forks to floor
before moving units.
5. Care and Maintenance
Our hydraulic furniture mover only requires little care and
maintenance, but this must be carried out regularly Depending on its
use, the spindles and gear wheels must be re-greased weekly or
monthly, using standard multi-purse grease. For this, the spindle may
be reached using a brush through the slot in the guide rail. The gear
wheels are also greased using brush, by first levering off the
gear-housing lid with a screwdriver. The lid should be pressed down
firmly to close it again. The units' function should be tested.

6. Parts Lists & Exploded Figures

Part NO. Description Qty.
1Main Frame 2
2Jack 2
3Screw 8
4Flate washer 4
5Lock washer 4
6A Wheel kit, PU+Steel 4
6B Wheel kit, All Steel 4
7Bolt 16
8Flate washer 16
9Lock washer 16
10 Hex nut 16
11 Bumper tube 2
12 Rubber pad 2
13 Jack handle 2
14 Handle 2