Global Solar Energy Power Bank User manual

Power Bank
User’s Guide

1
Introduction
The Power Bank is practical and easy to use and can be easily charged by Global Solar Energy, Inc.
(GSE) solar products. It is compatible with many mobile phones, PDAs, digital cameras and many
other devices by using the specialized connectors, making it a versatile travel companion.
In addition, the 12V CLA cable nearly completes the universal connectivity by enabling small
electronics loads (less than ~3.5Watts) to be operated through the customer-provided male CLA
adapter. CLA will not operate loads that are rated higher than 3.5 watts. Therefore, this battery bank
will typically not work with many of smart phones, PDAs, hand-held computers, pocket PCs, unless
they are listed in the compatibility section.
Please read this User’s Guide carefully before using the Power Bank. The suppliers assume no
responsibility for any damages that may happen with the improper operation of this product. Contact
your personal device supplier to ensure compatibility before connecting.
1. Product and Accessories
No. Names Quantity Remarks
1 Power Bank 1 pc. Figure 1
2 100-240VAC Wall Charger 1 pc.
3 CLA Auto Charger 1 pc.
4 DC connector for digital
camera 6 pcs./ set Figure 5
5 Universal cable for camera 1 pc. Figure 6
6 Universal adaptor for
Mobile phone and PDA 1 pc. Figure 4
7 Mobile phone cable 5 pcs. Figure 7
8 PDA cable 2 pcs. Figure 7
9 12V CLA cable 1 pc Figure 8
10 GSE Adapter Cable 28001 1 pc. Figure 9
11 GSE Adapter Cable 28002 1 pc. Figure 10
12 User guide 1 PC
Note: Figures are for reference only and are subject to change without notice

2
2. Technical Parameters
Items Parameters Remarks
Capacity of Built-in
Battery 3.6 V 2600mAh Li-ion battery
Power bank output
voltage DC: 5.2 V/ 6.2 V/ 7.2 V Adjustable
Power bank max
output current 1800mA
Power bank nominal
input voltage / current DC 4.8-5.2 V / 400 – 600mA
Adaptor output
voltage DC 5.2 – 13 V
Adaptor output
current 15- 700mA
Power bank
dimensions 102mm * 64mm * 26mm
Power bank net
weight 167 g
Safety certified CE / FCC
3. Illustration of the Product and Functions
Figure 1 (Power Bank Main Unit)
Figure 2 When TIP is accordant with “+”, DC connector is inner positive and outer negative

3
Figure 3 When TIP is accordant with “-”, DC connector is inner negative and outer positive
Figure 4 Universal Adaptor for Mobile Phone / PDA
Figure 5 DC Connectors for Digital Cameras
Figure 6 Universal Cable for Digital Cameras
Figure 7 Mobile Phone / PDA cable

4
Figure 8 Step-up cable for 12V CLA
Figure 9 GSE Adapter Cable 28001
Figure 10 GSE Adapter Cable 28002

5
4. General Operation Methods
4.1. Before using the power bank, check the capacity of the power bank battery: connect the 3.5 mm
DC connector digital camera or mobile phone / PDA adaptor to the DC jack of the power bank.
Then switch the voltage to the DC 5.2 V and press the battery capacity indicator button. The
table below will explain the battery capacity remaining for your reference.
Indicator Display Capacity
1 red LED 30%
1 red LED, 1 green LED 50%
1 red LED, 2 green LED 80%
4 LED Full
Note: The Battery Capacity indicator only works if 5.2V is selected and a plug is inserted
into output jack.
4.2. If the low battery indicator lights up during work mode, recharge the power bank: connect the DC
connector of the travel charger or car charger to the power bank to commence charging. When
charging, the charge indicator lights up and will fade out automatically once charging is
complete. It is advisable to charge overnight before using the first time.
4.3. Charging a digital camera
a. Select the right size DC connector for your digital camera.
b. Correctly connect DC connector to digital camera. If the camera charging jack is inner
positive and outer negative, a “+” symbol on the DC connector should be accordant with the
“TIP” symbol on the digital camera cable (see Figure 2); If the camera charging jack is inner
negative and outer positive, a “-” symbol on the DC connector should be accordant with the
“TIP” symbol on digital camera cable (see Figure 3).
c. Select the voltage required by the digital camera, i.e. 5.2 V, 6.2 V or 7.2 V.
d. After Connecting the DC connector to the digital camera, insert the digital camera cable to
the power bank’s DC jack to commence charging.
WARNINGS: 1. Please ensure that the connection between the digital camera cable is correct
as the wrong connection will damage the connected devices.
2. Do not push the voltage switch when charging devices, the connected device
may be damaged.
4.4. Charging a mobile phone / PDA
a. Select the right size cable that the mobile phone / PDA requires.
b. Connect the mobile phone / PDA cable to the universal adaptor.
c. Switch the voltage to DC 5.2 V.
d. Connect the mobile phone / PDA connector to the mobile phone / PDA and connect DC
connector to the output jack of the battery bank.
WARNING: Do not push the voltage switch when charging the mobile phone or PDA, or the
connected device may be damaged.
4.5. Charging devices through the CLA
a. Select the 12V CLA Cable (Figure 8)
b. Connect the CLA adapter for your cell phone / PDA to the CLA cable receptacle
c. Switch the voltage to DC 5.2V.
d. Connect the 12V CLA cable to the output jack of the battery bank
5. Special Considerations When Utilizing Solar for Charging Battery
5.1. Unfold and place the Solar Panel in a sunny location
5.2. Tilting or propping the module towards the sun reduces the charge time.

6
5.3. Batteries are not intended for use at temperatures higher than approximately 45C (122F) or
below 0C (32F). Be sure to place the Battery Bank in the shade during charging to avoid over-
temperature and damage.
5.4. The attachment from the GSE solar module can be made using a 5.5mm OD, 2.1mm ID barrel
plug adapter. To enhance this connectivity, GSE offers:
a. the GSE adapter cable #28001 [See Figure 9] to go from 2-prong SAE connector to barrel
plug, and
b. the GSE adapter cable #28002 [See Figure 10] to adapt from a 2.5mm ID to a 2.1mm ID
barrel plug.
5.5. Estimated Charging times are shown in the table below for charging the Battery Bank with
different sizes of Solar Product.
Charging Method EstimatedCharging Time
SunlinQ12 Solar Module* 4-6 hours
SunlinQ6.5 Solar Module* 7-8 hours
~6V, Quarter cell Solar Module (e.g. ScotteVest cape) 10-15 hours
100-240VAC Wall Charger 7-8 hours
12VDC* 7-8 hours
*Assumes charged through the CLA Adapter provided for best efficiency
Note: Charge times assume that the module is sitting in direct sunlight and tilted toward the sun.
6. Precautions
6.1. Keep this product in a dry place. Never place or use the product in wet or dirty conditions.
6.2. Never throw this product into a fire.
6.3. Never throw or drop this product to avoid causing damages.
6.4. If you do not plan to use the product, please disconnect digital camera cable or 3.5 mm DC
connector of universal adaptor from the power bank. The power bank will change to power
saver mode to conserve the battery.
6.5. If battery level of charge is less than ~10%, the internal controller automatically switches to
Power Saver mode (i.e. trickle charging). To reset, assuming Low Power Light is on, disconnect
load, disconnect and reconnect the input plug, and charge for 15-30 minutes prior to
reconnecting load.
6.6. Never attempt to alter or disassemble the product. If there is a problem with the product please
contact your dealer for further assistance.
7. POWER BANK COMPATIBILITY
As described above, the Power Bank is compatible with many mobile phones, PDAs, digital cameras
and many other devices by using the optional charger connectors, making it a versatile travel
companion. In addition, the 12V CLA cable nearly completes the universal connectivity by enabling
small electronics loads (less than ~3.5Watts) to be operated through the customer-provided male
CLA adapter.
Please see the following links for helpful CLA attachments for your electronics:
www.belkin.com
www.ziplinq.com
www.thesupplynet.com
Warning: Be sure to check the compatibility of your electronics prior to attaching to Power Bank to
avoid any possible damage. Contact your electronic supplier first.
Adaptor Designation Compatibility With
SIM C55 Siemens Cell Phones
MOT V60 Motorola Cell Phones
NKI6110 Nokia Cell Phones
ERIT68 Ericsson Cell Phones
SAM E700 Samsung Cell Phones

7
PALM 505 PalmOne Tungsten and Zire series handhelds
PDA IPAQ HP iPAQ series, Asus MyPal series, Toshiba
e800, Mio 168 Pocket PC Phones and imate
Pocket PC Phones
12V CLA Various products through customer-supplied
CLA (which require less than 3.5 Watts)
The cell phone manufacturers with a direct-connection adapter are noted above and the specific
listing of compatibilities is shown below. If your cell phone is not listed, then a 12V CLA adapter
or one of the USB adapters may still be able to operate :
1.SIM C55: Siemens
C55/S55/SL55/M55/A55/A56/C56/CT56/S56/C60/A60/C62/MC60/S57/2128/CF62/CFX65/CX65/CX70/CX70
Emoty/SF65/SK65/SL65
2.ERI T68: Ericsson
ERIT28/T28Word/A26/8S/A2638SC/T20S/K600/29S/T39/R320S/R380S/R520M/T60/T61/T20/R20/R278/T68/T65/T6
6/T300/T310/T610/T316/T616/T630/Z200/A2628/T500/T600/T400/P800/T618/T312/T62/TF500i/K700i/P800/P900/P9
10/S700i/T100/T200/T230/T68i/V800/Z1010/Z200/Z500/Z600/T39M/R600/T68#
3.NKI 6110: Nokia
NOK6110/5110/6162/6150/6160/6210/6310/6138/6650/6200/6500/5510/6510/6600/6220/5100/6100/6108/6590/6610
i/6610/6630/6670/6800/6820/5510/5100/5140/7110/7210/7650/7700/7270/7260/7600/7280/7250/7250i/7610/3330/33
10/3320/3360/3390/3510/3650/3200/3585/3570/3588i/3315/3210/3100/3105(CDMA)/3600/8210/8310/8250/8810/885
0/8290/8260/8279/8890/8855/8260/8910/8910i/9210i/9300/9500/2300/1261/N-Gage/N-Gage QD;
4.SAM E700: Samsung
A288/A200/A300/A388/A400/A408/N200/N288/R200/R210S/A800/S300/V200/V205/V208/5CH200/A308/C100/R225/
R235/A530/V206/E105/X100/X600/E700/X105/T100/T108/T208/T508/N500/N600/R220/N620/N628/E820/X450/E80
0/E400/E600/E710/P400/P510/C110/D410/E300/E310/A500/C200/E330/N400/P100/Q200/S300M/T410/T500/V100/
X100/X120/X400/X430/X460
5.MOT V60: Mototola
V60/66/I85/I90C/I100/I500/I30V120/V70/V200/P280/270C/V60C/V60I/T721/T722/V120T/V120C/V120X/V120E/V60C
/V60I/2800/V500/V600/V525/V60t/V300/I90C/I80C/A835/A920/A925/T720/V547/V550/V620/V80/V980/C975/C980/T
720i/E398/MPX/MPX220
Reference Info
1. The maximum input voltage to the Power bank is 15V
2. CLA input cable (which reduces the input voltage to match the battery voltage) to the Power bank
has an input rating of 12-24V but withstands 26V (i.e. the Voc of OEMs and P3s (except for P3-
15W))
3. The efficiency of the CLA is ~75%
4. The 12VCLA cable will not operate loads that require more than 300 mA of current (~3.5 Watts at
12V)