GM Lighting Vision120 RGBW User manual

WARNING!
FAMILIARIZE YOURSELF WITH
INSTRUCTIONS BEFORE PROCEEDING.
FOLLOW ALL LOCAL CODES. VERIFY THAT
POWER IS OFF BEFORE PROCEEDING.
2.4 Ghz WiFi SIGNAL REQUIRED.
Vision120™ RGBW
Dry / Wet Location 120V RGBW LED Tape
NOTE: WE RECOMMEND THAT YOU ENGAGE A QUALIFIED,
LICENSED ELECTRICIAN. MODIFYING OR DISASSEMBLING
BEYOND INSTRUCTIONS WILL VOID THE WARRANTY FOR THIS
PRODUCT.
Download the LUXcontrol™ App
Vision120 RGBW is controlled wirelessly through our LUXcontrol
app that is available for iOS and Android devices. Download
from the App Store or Google Play. Please register to use the
app. Access the QR codes at right for more information.
Layout and Pre-Configure Components
Before You Begin Installation
Locate area where Vision120 RGBW tape, mounting
channel and controller are to be mounted. Make sure that
this space is free of obstructions and can be easily reached for
mounting or maintenance. Tape is pre-cut and configured by
the factory. Do not attempt to cut in the field or alter in any
way.
Pair Before Mounting
Whenever possible, it’s important to be close to your WiFi
source when pairing a LUXcontrol device. Fig. 1. This is true for
any device that depends on a WiFi signal. NOTE: LUXcontrol
recognizes a 2.4Ghz. signal. Consult the pairing directions that
comes with the controller, or watch our LUXcontrol pairing
video. It’s important to turn the controller on and off three
times to get light blinking rapidly in order to pair. Once
connected, proceed.
Mounting Controller
Locate controller close to 120V power source and connect.
Fig. 2. Locate mounting tabs and mount controller to surface
using counter sink screws. Fig. 3. For outdoor location, please
follow all codes that may pertain to wet rated enclosures.
Connect toConnect to
120V Current120V Current
®18700 Ridgeland Ave., Tinley Park, IL 60477
Toll-Free: [phone] • FAX: [phone]
www.gmlighting.net
[email protected] V120-RGBWinstructions_043021
120
VOLT
FIELD
CUTTABLE
65
IP
LOCATION
90
+
CRI
RGBW
WET
LOCATION
NOT 3 Yr.
WARRANTY
Fig. 1
Fig. 3
INLINE FUSE
N
N
LL
8 amp V120 fuse (replaceable)
Included with tape and required for warranty
Fig. 2
G
R
B
W
NEMA
ENCLOSURE
(RECOMMENDED)
OR
JUNCTION BOX
BY OTHERS
FOR OUTDOOR
APPLICATIONS
WATERPROOF CONNECTOR
V120-RGBW TAPE
GM-WPSC-RGBW
Trim to needed length
Fig. 4
SCAN FOR
V120-RGBW VIDEO
SCAN FOR
LUXcontrol VIDEO

Vision120™ RGBW
Dry / Wet Location 120V RGBW LED Tape
Preparing the Mounting Surface
Dust will hamper adhesion. Clean all surfaces
thoroughly. Fig. 5. Wear protection, do not breathe in fumes.
Mounting Tape to Surface
Vision120 RGBW can be mounted one of three ways:
1. Using 3M Double-Sided Tape
Adhere a length of V120-3M-VHB-15 tape to the back of the
V120-RGBW tape. Make sure that tape is applied without kinks
or bends. Remove the paper protective strip to reveal the
adhesive. Fig. 6. Applying firm pressure, burnish the tape to
the surface with your fingers or a small roller. Do not apply too
much pressure or you may damage the diodes.
2. Using Mounting Clips
Arrange V120-RGBW-MC mounting clips along the length of
your V120-RGBW run, allowing for at least 1 clip for every 12”.
Mount the clips to the surface by using the screws supplied.
Fig. 7. Press tape against prongs of clips until the clips open
slightly allowing the tape to be firmly seated.
3. Mounting In Channel (See exploded dwg. Fig. 8)
The V120-RGBW-CHL4 and 8 are supplied with internal
mounting clips that will hold the V120-RGBW tape securely in
the channel. Mount channel by drilling mounting holes through
the channel, into the surface. Fig. 9. Counter-sink screws are
then used to mount the channel to the surface. End caps are
available to achieve a finished look. Press lens firmly into the
rails of the channel. You will hear and feel the lens pop into
place. NOTE: Connectors do not fit inside of channel.
For outdoor applications, we recommend that you run a bead
of water-proof silicone sealant around the base of the channel
to seal. Fig. 10.
Powering Up
Make sure that power source to controller is
supplying 120V current. Since you have
pre-paired the controller with the
LUXcontrol app, you can now turn the V120-RGBW tape on,
and orchestrate a variety of transitions, scenes and
colorful eects.
Fig. 6
12”
Fig. 7
Fig. 9
Fig. 10
®18700 Ridgeland Ave., Tinley Park, IL 60477
Toll-Free: [phone] • FAX: [phone]
www.gmlighting.net
[email protected] V120-RGBWinstructions_043021
Fig. 5
V120-RGBW-ECC
(Set of 2)
V120-RGBW-CHL4/8
(4’ / 8’)
LENS
TO CONTROLLER
V120-RGBW TAPE
POSITION OUTSIDE
OF CHANNEL
POSITION OUTSIDE
OF CHANNEL
Fig. 8