Godox Quicker300D User manual

说 明 手 册
Instruction Manual
中英文双语
Chinese English Bilingual
Made in China
深圳市神牛摄影器材有限公司
地址: 深圳市宝安区福海街道塘尾社区耀川工业区厂房2栋
电话/Tel: [phone](8062) 传真/Fax: [phone] 邮箱/E-mail: [email protected]
godox.com
Add: Building 2, Yaochuan Industrial Zone, Tangwei Community, Fuhai Street,
Bao’an District, Shenzhen, China Tel: [phone](8062) Fax: [phone]
E-mail: [email protected]
GODOX Photo Equipment Co., Ltd.
705-Q600D0-00
Instruction Manual
说 明 手 册
Made in China

: 2
/Tel: [phone](8062) /Fax: [phone] /E-mail: [email protected]
godox.com
Add: Building 2, Yaochuan Industrial Zone, Tangwei Community, Fuhai Street, Bao’an District,
Shenzhen, China Tel: [phone](8062) Fax: [phone] E-mail: [email protected]
GODOX Photo Equipment Co., Ltd.
705-Q600D0-02

- 01 -
前 言
感谢您使用闪客Quicker D系列影室闪光灯，此产品持久耐用，功能齐全，性能强大，
全方位支持专业摄影师的各种光效创意，是专业影楼和摄影工作室的理想必备光源，适用于
婚纱摄影、广告拍摄、人像以及时尚摄影等。产品有以下亮点：
30级闪光强度随意选择，LED数码显示屏从5.0-8.0准确定位输出功率；
150W大功率造型灯，亮度无级可调；
输出稳定，同一功率连续输出变化不超过2%；
防预闪功能，带一次预闪功能的相机用光控可实现同步拍摄；
自动放电功能，无需预闪放电；
人机工程学面板，3秒后调节参数智能记忆、开机自动恢复；
选购FT-16无线功率遥控器，可无线控制闪光灯功率、造型灯、蜂鸣及触发引闪。
目 录
- 02 -
01前言
02警告
02注意事项
03部件
03• 机身
03• 附件
04• 可选购附件
04使用
04• 固定闪光灯
04• 接通电源
04• 造型灯使用
05• 功率调节
05• 试闪按钮
05• 同步触发
05• 光控使用
05• 声音提示
05• 记忆存储功能
05• 无线控制功能
06• 装卸闪光灯管
06产品参数
07维护保养
在使用本设备前请仔细阅读以下警告内容，并妥善保管以便所有本产品使用者可随时
参阅。
请勿私自拆卸产品，如产品出现故障须由本公司或授权的维修人员进行检查维修。
请保持干燥：请勿用湿手接触产品，亦不可将产品浸入水中或暴露于雨中。
请勿让儿童接触本产品。
摄影灯适用于通风的环境,使用时请保持灯光源部分及散热孔不被堵塞，请勿在易燃
易爆的环境中使用。
摄影灯采用电源插头做为断接装置，应保持随时便于操作。
使用时严禁用手接触灯光发热部件。
安装及连接附件时，请关闭开关断开电源，装卸闪光灯管/造型灯时，请确认灯管为
冷却状态，避免烫伤，还需佩戴绝缘手套。
请勿将闪光灯头正对人眼闪光(特别是婴儿的眼睛)，否则可能会在短时间造成视力
障碍。
在不使用时，请断开电源。
注意事项
闪光灯在全功率的情况下连续引闪30次后，需冷却3分钟左右。如果连续使用而不
冷却就会产生高温积热。
不可长时间连续使用造型灯，否则可能造成安装在灯头上的柔光箱等易燃附件燃
烧。有易燃附件时建议不要连续使用造型灯超过10分钟。如使用超过10分钟，请
冷却1分钟后再继续使用。
使用束光筒时，请勿长时间点亮造型灯或过频闪光(全功率每分钟不多于6次)。积
热会导致闪光灯外壳受损或造成灯的损坏。
避免突然的碰撞，防止闪光灯管或造型灯受损。
警 告

机身
部 件
01.电源插座
02. 同步线插孔
03. 电源开关
04. 造型灯亮度调节旋钮
05. 闪光灯管功率调节旋钮
06. MODEL造型灯按键
07. SOUND蜂鸣按键
08. SLAVE光控模式按键
09. TEST试闪按键
10. 数码显示屏
11. 造型灯指示灯
12. 蜂鸣指示灯
13. 光控指示灯
14. 试闪指示灯
15. 光控接收器
16. 保险丝座
17. 托架
18. 伞孔
19. 方向调节把手
20. 无线控制插座
15
04
01
07
02
08
19
14
09
10
03
05
06
11
12
16
17
13
18
20
可选购附件
可搭配本公司以下摄影附件使用，以获得最佳的拍摄效果和使用体验：
逆变器、柔光箱、反光伞、灯架、蜂巢、雷达罩、束光筒等。
使 用
固定闪光灯
1、取下灯头保护罩，装上造
型灯并套上玻璃灯罩和反光
灯罩(另购)。(如想卸下反光
灯罩，请往后按压灯头上的
蓝色附件释放钮，同时逆时
针旋转反光灯罩至松开即
可，如图)
2、将闪光灯设备安装在一个
合适的灯架上，调整好托架
(17)并扭紧固定，方向调节
把手(19)可按用户要求调节
灯的方向。伞孔(18)可以插上各类影楼伞。
接通电源
通过电源线把闪光灯接通到交流电源上，拨动闪光灯上的电源开关(3)，此时电源开关上
的小灯亮，表示连接正常。
造型灯使用
造型灯按键(6)控制造型灯的打开和关闭。当造型灯指示灯(11)点亮时，表示造型灯打
开；造型灯指示灯(11)熄灭时，表示造型灯关闭；造型灯亮度调节旋钮(4)可对造型灯的
亮度进行设置；造型灯点亮2小时后会自动关闭，以防在无人状态时长时间点亮导致高温
积热。
如有易燃附件安装在灯头上，不可长时间点亮造型灯，最好是点亮10分钟后
冷却1分钟再继续使用，并注意易燃附件的温度。
- 04 -- 03 -
FUSE: 5A
AC220V-240V~50Hz
1. 电源线
2. 灯头保护罩
3. 玻璃罩
4. 造型灯
5. 说明书
附件
4
321

功率调节
闪光功率通过功率调节旋钮(5)来控制，可以从“5.0”至“8.0”自由调节，数码显示屏
(10)将对所选择功率作准确显示，满足客户在不同环境下对光源的要求。数码显示屏
(10)显示“OF”时，表示闪光灯引闪功能关闭。从高档调节至低档，有自放电功能，不
需引闪放电。
试闪按钮
欲使闪光灯测试闪光而不拍照，请按试闪按钮(9)。摄影师可以通过试闪按钮结合功率调
节旋钮(5)来调节闪光亮度。
同步触发
同步线插孔(2)规格为Φ6.35mm，此处
可插入同步线或者触发器触发插头对闪
光灯进行同步引闪。
光控使用
光控模式有3种选择，由SLAVE光控模式
按键(8)进行切换。
◆非光控模式：光控指示灯(13)不亮，表示光控功能已关闭。
◆1次引闪模式：光控指示灯(13)亮蓝色，表示闪光灯接收到1次外界闪光可以同步触发闪
光。此模式下，可做副灯使用，创造多种光影效果。
◆2次引闪(防预闪)模式：光控指示灯(13)亮红色，表示闪光灯在2秒内接收到2次外界闪
光，接收到第2次时可以同步触发闪光。此模式下，可以做副灯使用，适用于TTL闪光环
境。具有防预闪功能，使用带一次预闪功能的相机能用光控实现同步拍摄。
声音提示
蜂鸣按键(7)控制蜂鸣提示的打开和关闭，当蜂鸣指示灯(12)点亮时，表示蜂鸣提示音打
开；当蜂鸣指示灯(12)熄灭时，表示蜂鸣提示音关闭。
每次回电充满时会响“BI—”一声，提示可以引闪。
记忆存储功能
闪光灯设有参数记忆功能，调节参数3秒后未变更的，闪光灯会自动存储设置好的参数。
下次开机使用时初始设置跟关机前一致。
无线控制功能
功率遥控器的接收器插入“无线控制插座(20)”，手持功率遥控器可远程控制闪光灯的功
率开关和大小、造型灯开关、蜂鸣器开关，也可以连接相机热靴来同步引闪闪光灯。
产品参数
装卸闪光灯管
关闭所有电源并拔下电源线，带上绝缘手套，将闪光灯管上的铁丝拧松，用平衡力拿住灯
管两脚间，轻轻往外拉出卸下旧灯管。将旧灯管两脚上的套管取下套到新灯管两脚，拿住
新灯管两脚间，对准灯头上两铜柱，用平衡力往里推进。最后将铁丝绕灯管弹片并拧紧固
定好灯管。
- 06 -- 05 -
型号
闪光能量
闪光指数(m ISO 100)
色温
电源电压
闪光功率调控
造型灯功率
回电时间
闪光触发控制方式
闪光持续时间
同步端口输出参数
USB端口输出参数
保险丝
尺寸
净重
Quicker300D
300WS
58
5600±200K
AC110V-120V~60Hz 或 AC220V-240V~50Hz
OFF, 5.0~8.0(1/32~1/1)
150W
0.3~1.2秒
同步线插孔，光控感应，试闪按钮，无线控制插座
1/2000S~1/800S
灯体直径Φ14CM 含把手高23CM 含保护罩长41CM
Quicker400D Quicker600D
400WS 600WS
65 76
约2.7KG 约2.8KG 约3KG
9V
5V/200mA (仅限神牛接收器)
AC220V-240V~50Hz: 5A AC220V-240V~50Hz: 8A
0.3~1.5秒

维护保养
闪光灯在工作时，如发现异常，应立即关掉电源，查明原因。
灯体应避免震动，平时注意表面除尘。
灯体稍有发热为正常现象，无特别需要时，勿连续引闪。
除灯管与造型灯消耗品允许用户用原厂配置的自行装卸更换外，闪光灯的其他维护
概由本厂指定可供原厂配件之维修部负责。
1年保修，由于灯管与造型灯为消耗品，不在1年保修范围。
擅自检修此闪光灯，经发现将取消闪光灯之一年保修期，维修需要收取相关费用。
如果本品出现故障或者被水淋湿，唯有在专业人员维修后方可继续使用。
在维修和清洁本品时请断开电源。
如有技术更改，恕不另行通知。
FOREWORD
Thanks for choosing Quicker D series studio flashes. It is a durable and high-
performance strobe with complete functions to help professional photographers
create various lighting effects. This product is suited for wedding, advertisement,
portrait, and fashion photography. The perfect light source and A MUST in studios
and photo workshops! Among the benefits you will enjoy:
CONTENTS
Precise output control on LED display, 30 steps from 5.0-8.0 by 0.1 increment;
High-qualified modeling lamp, 150W output adjustable;
Outstanding output stability, a tolerance of ≤ 2% under the same output;
Anti-preflash function, enables synchronization with cameras having a one-preflash firing
system;
Automatic power discharge when the flash output is adjusted from high to low;
Adjusted parameters intelligently remembered after 3s and automatically recovered after
a restart.
Flash output on/off and power level,modeling lamp and buzzer on/off,and flash triggering
can be controlled by using Godox FT series romote control.
- 08 -- 07 -
08Foreword
09Warning
09Caution
10Names of Parts
10• Body
10• Accessories
11• Separately Sold Accessories
11Operations
11• Flash Preparation
11• Power Connection
11• Modeling Lamp
12• Power Output Control
12• Test Button
12• Sync Triggering
12• Slave Trigger Model
12• Buzz Function
12• Memory Function
13• Wireless control Function
13• Tube Replacement
14Technical Data
14Maintenance

15
04
01
07
02
08
19
14
09
10
03
05
06
11
12
16
17
13
18
Body
NAMES OF PARTS
01. AC Power Socket
02. Sync Cord Jack
03. Power Switch
04. Modeling Lamp Output Controller
05. Flash Output Controller
06. Modeling Lamp Button
07. Sound Button
08. Slave Model Button
09. Test Button
10. Digital Display
11. Modeling Lamp Indicator
12. Buzz Indicator
13. Slave Triggering Indicator
14. Test Indicator Lamp
15. Light Sensor
16. Fuse
17. Mounting Bracket
18. Umbrella Input
19. Direction Adjusting Handle
20.Wireless control port
1. Power Cord
2. Lamp Cover
3. Glass Protection Cover
4. Modeling Lamp
5. Instruction Manual
Accessories
20
- 10 -- 09 -
To prevent damage to the product or injury to you or to others, read the
following warnings in their entirety before using this product. Keep these
Warnings where users can read them for ready reference.
Do not disassemble or modify. Should the product break down, send the
defective back to the authorized service center for inspection and maintenance.
Keep dry. Do not handle with wet hands, immerse in water, or expose to rain.
Keep out of reach of children.
Please put the device in a ventilation environment and keep the parts of lighting
and heat dissipation holes are unobstructed. Do not use in flammable
environment.
As this product adopts make and break device, please keep it easy to be used.
No touching the heating parts of this product.
Please turn off the power and wear insulated gloves before installing and
connecting accessories. When replacing the tube or modeling lamp, please
make sure that the tube is cool and wear insulated gloves to prevent burns.
Do not flash directly towards naked eyes (especially those of babies), otherwise
it may lead to visual impairment.
Disconnect from the power supply when it will not be used for an extended
period.
CAUTION
After 30 continuous flashes at full power, the flash should be cooled down for
about 3 minutes. Overheating will occur if it is used continuously without cooling
down.
Do not keep using the modeling lamp for a long time; otherwise flammable
accessories attaching to flash head, e.g. softbox will get burnt. A 10-minute time
is recommended in this case. After 10 minutes, cool it down for 1 minute.
When using a snoot, do not keep the modeling lamp on for a long time or fire too
frequently (not over six times for one minute). Overheating will result in damages
for strobe housing and/or studio light.
Avoid sudden impacts as this can damage the flash tube and/or modeling lamp.
Warning
FUSE: 5A
AC220V-240V~50Hz
4
321

Separately sold accessories
The product can be used in combination with the following accessories sold separately,
so as to achieve best photography effects:
Power Inverter, Softbox, Photographic Umbrella, Light Stand, Barndoor, Snoot, etc.
OPERATIONS
Flash Preparation
1. Take down the lamp
cover. Install the modeling
lamp and put on the glass
protection cover and the
standard reflector (optional
accessory).
(To uninstall the standard
reflector, press the blue
release button on the flash
head and turn the standard
reflector counter-clockwise to take it out, as illustrated in the picture.)
2. Attach the flash unit on an appropriate light stand. Adjust the mounting bracket (17)
for a good angle and make sure it is tightened and fixed. Use the direction adjusting
handle (19) to adjust the flash to a desired direction. Umbrella input (18) is for different
photographic umbrellas to put in.
Power Connection
Use the power cord to connect the flash to an AC power source and turn on the power
switch (3). The lamp on the power switch turns on, indicating it’s connected.
Modeling Lamp
Modeling lamp button (6) controls the modeling lamp status: Modeling lamp indicator
(11) is on, indicating the modeling lamp is on; Modeling lamp indicator (11) is off,
indicating the modeling lamp is turned off. Modeling lamp output controller (4) can be
used to adjust the modeling lamp power output. Modeling lamp will be off automatically
after lighting for 2 hours, in case overheating occurs when user is not nearby to turn it
off.
When there is flammable accessory on the flash unit, do not keep the
modeling lamp on for a long time. It is recommended to cool it down for one
minute after 10 minutes' working.
Power Output Control
Flash output controller (5) decides different power output, satisfying light requirements
in different environment. The power is adjustable from 5.0 to 8.0 which will be
accordingly shown on the digital display (10). "OF" on the display indicates that the
flash triggering function is shut down.It can automatically discharge power when the
flash output is adjusted from high to low.
Test Button
To fire the flash without taking a picture, press the test button (9). It can also help
adjust the flash brightness when using together with the flash output controller (5).
Sync Triggering
The sync cord jack (2) is a Φ6.35mm
plug. Insert a trigger plug here and the
flash will be fired synchronously with
the camera shutter.
Slave Trigger Model
Three slave triggering models are
available and can be set by pressing
Slave Model Button (8).
◆ No optical control: The slave triggering indicator (13) is off, indicating the slave
triggering function is shut down.
◆ One fire model: The slave triggering indicator (13) glows blue, indicating the flash
will fire synchronously on one external flash. In this model, the flash can function as an
auxiliary lamp, offering various effects of light and shadow.
◆ Anti-preflash model: The slave triggering indicator (13) glows red, indicating the
flash will receive two external flashes within 2 seconds and will fire synchronously on
the second flash. In this model, the flash can function as an auxiliary lamp, applicable
to TTL system. With this anti-preflash function, synchronization is supported with
cameras having a one-preflash firing system
Buzz Function
The sound button (7) is used to decide whether there is sound reminder for ready flash
after recharging. When the buzz indicator (12) is on, the buzz function is working; if it is
off, the buzz function is shut down. A “BI” sound will be heard when it’s fully charged.
Memory Function
The device is equipped with memory function for the panel setting. It will help
remember the panel setting 3 seconds after you set it. When starting up the flash next
time, the panel setting will be the same as that before powering it off.
- 12 -- 11 -

Wireless Control Function
By using the wireless power-control flash trigger, you can wirelessly control the on-
and-off of your flash, modeling lamp and buzzer, as well as adjust the flash output
level. To start this function, insert the trigger receiver into the Wireless Control Port
(20) and make settings on the trigger. You can also press the camera shutter-release
button to trigger the flash by setting the transmitter hotshoe onto the camera hotshoe.
Tube Replacement
Shut down the power and remove the power cord before replacing the flash tube and
wear insulated gloves. Then, loosen the iron wire on the tube, keep a balanced hold
on the two feet of the flash tube and pull out the old tube gently. Take down the feet
casing from the old tube and put them on the new tube. Hold two feet of the new tube
and target directly towards the two copper outlets, then push them slightly in. Twine
the iron wire on the stainless steel sheet to fix the flash tube.
TECHNICAL DATA
MAINTENANCE
Shut down the device immediately when it works abnormally and find out the reason.
Avoid sudden impacts and the lamp should be dedusted regularly.
It’s normal for lamp being warm when in use. Avoid continuous flashes when not
necessary.
Maintenance of the flash is up to our authorized maintenance department which can
provide original accessories, expect that users can replace the flash tube and modeling
lamp provided by the manufacturer.
One year warranty period will be cancelled when any unauthorized maintenance is
found.
If the product had failures or was wetted, it can be further used only after repaired by
professionals.
Disconnect the power when doing maintenance work or cleaning.
New changes made to the specifications or designs may not be updated in this manual.
- 14 -- 13 -
Dimension
Net Weight
Flash diameterΦ14CM, height of flash with handle 23CM,
length of flash with lamp cover 41CM
Approx. 2.7KG Approx. 2.8KG Approx. 3KG
AC220V-240V~50Hz: 5A AC220V-240V~50Hz:8A
Model
Max Power (WS)
Guide Number(m ISO 100)
Color Temperature
Operating Voltage
Power Output Control
Modeling Lamp (W)
Recycle Time
Triggering Method
Flash Duration
Parameters Output from
the Sync Cord Jack
Parameters Output from the USB Port
Fuse
5600K±200K
AC110V-120V~60Hz or AC220V-240V~50Hz
OFF, 5.0~8.0(1/32~1/1)
150W
sync cord, test button, slave, wireless control port
1/2000S~1/800S
9V
5V/200mA (only for the receiver)
Quicker300D
300WS
58
Quicker400D
400WS
65
Quicker600D
600WS
76
0.3~1.2sec 0.3~1.5sec