Godox ThinkLite TT660 II User manual

说 明 手 册
Before using your product, please read this user manual carefully in
order to ensure your safety. Keep it properly for reference in future.
FOREWORD
Thank you for purchasing a GODOX product.
GODOX camera flash TT660II fits various standard hotshoe-
mounted DSLR cameras from Canon, Nikon, Pentax, and Olympas,
etc. The TT660II offers:
● Wide Power Control Range(1/1~1/128)
● 22 steps of precise adjustment to gain better light effect
● Stable color temperature of 5600±200K
● Supports Multi/Stroboscopic flash, S1/S2 slave triggering flash, etc
● Achieving high-speed sync with remote control
中英文双语 / Chinese English Bilingual
Electronic Camera Flash
82.ATT66020-00VA

●
battery contact due to the irregular shape of the battery contacts.
● If you change the batteries after firing many flashes continuously, be
aware that the batteries might be hot.
Using size-AA batteries other than the alkaline type may cause improper
Recycling Time and Flash Count
Take AA alkaline batteries (LR6)
as an example:
● Based on new size-AA alkaline batteries.
● The battery level indication on the LCD panel will blink if the remaining battery level
is too low to be charged. Please replace the batteries.
Recycling Time
Approx. 0.1–5sec
Flash Count
Approx. 100-700
●
batteries, replace all four at one time.
● Size-AA Ni-MH or lithium batteries can also be used.
Use a new set of four batteries of the same brand. When replacing the
1. Always keep this product from rain or damp to avoid fire or
electric shock.
2. This device contains high-voltage electronic parts inside. Do
not disassemble or repair it. If you touch the high-voltage
circuit inside the product, electric shock may occur. Send it to
the authorized maintenance center for repair if needed.
3. Stop using this device if it breaks open due to extrusion,
falling or strong hit. Otherwise, electric shock may occur if you
touch the electronic parts inside it.
4. Do not fire the flash direct to the eyes (especially those of
babies) at short distance, or it may damage eyes. When taking
picture for babies, it is recommended to keep the flash unit at
least 1 meter (3.3 feet) away from them. Using bounce flash to
reduce light intensity is also suggested.
5. Always keep batteries or anything that may pose an
ingestion hazard out of children’s reach. Please contact a
doctor immediately if ingestion occurs.
6. When there is caustic liquid leakage inside, wear gloves
before taking out batteries.
7. Do not use the flash unit in the presence of flammable gas,
chemicals and other similar materials. In specific circumstance,
these materials may be sensitive to the strong light emitting
from this flash unit and may cause fire or electromagnetic
interference. Please pay attention to the warning marks in the
shooting surroundings.
8. Do not leave or store the flash unit in temperature over 40°C
(e.g. in automobile), or it may damage the electronic parts.
9. The flash unit is not waterproof. Please keep it away from
rain or humidity.
10. Please take out all batteries and keep the flash unit in dry
places if it will remain unused for long.
WARNING
Built-In Wide Panel
Flash Head
Optic Control Sensor
Charging Socket
Socket Cover
Hot Shoe Stand Hot Shoe Contact
Lock Ring
Reflection Card
PC Sync Socket
I. Name of Parts
Accessories
To achieve better performance and light effects, Thinklite camera
flash can be operated with such products as, PB960 power pack,
honey comb, color filter, etc.
Mini Stand
Mode Selection
Power Switch
LCD Panel
Zoom Selection
C.Fn Custom
Function
“+” Button
Set Button
Test Button/
Flash Ready Indicator
“-” Button
SLAVE Selection
Battery
Compartment
1.Installing the Batteries
Install four-size AA batteries.
1. Open the cover.
● Use your thumb to press the
battery compartment cover, and
then slide it to open the cover.
2. Install the batteries.
●
battery contacts are properly
oriented as shown in the
compartment.
Make sure the "+" and "–"
3 Close the cover.
●
cover as shown by the arrow to
close it.
.
Slide the battery compartment
II. Installation

III. Using the Camera Flash
1. Power Management
Use ON/OFF Power Switch to power the flash unit on or off. Turn
off if it will not be used for an extended period of time.
2. Power Control
The flash output is adjustable from 1/1 full power to 1/128th power
in 1/3rd step increments. To obtain a correct flash exposure, use a
hand-held flash meter to determine the required flash output.
Press the “-“ or ”+”button to adjust the flash power output.
● M Mode: Set the flash output from 1/1 full power to 1/128th
power in 1/3rd step increments.
● Multi Mode: Set the flash output from 1/4 full power to 1/128th
power in 1 step increments.
● Manual High-Speed Mode: Set the flash output from 1/1 full
power to 1/16th power in 1/3rd step increments.
3. ZOOM: Setting the Flash Coverage
● Set the flash coverage manually to match the lens focal length
from 24mm to 105mm.
● Press the ZOOM button and its settings can be adjusted by
pressing “+”or “-”button.
Note: When setting the flash coverage, the lens focal length
should be covered in case of occurring dark periphery.
4. M Mode
Press Mode Selection Button to enter M mode. In this mode, you
can set the camera flash onto your camera’s hotshoe or trigger to
fire flashes. During shooting, adjust the power output and press the
camera shutter, then the camera flash will fire a flash under the
camera synchronous signal.
5. Multi: Stroboscopic Flash
Press Mode Selection Button to enter Multi mode. With
stroboscopic flash, a rapid series of flashes is fired. It can be used
to capture a multiple images of a moving subject in a single
photograph.
2. Attaching to the Camera
1. Attach the camera flash.
● Slip the camera flash’s mounting
foot into the camera’s hot shoe all
the way.
2. Secure the camera flash.
● Rotate the locking screw on the
mounting foot until it locks up.
3. Detach the camera flash.
● Rotate the locking screw on the
mounting foot until it is loosed.
You can set the firing frequency (number of flashes per sec.
expressed as Hz), the number of flashes and the flash output.
Calculating the Shutter Speed
During stroboscopic flash, the shutter remains open until the firing
stops. Use the formula below to calculate the shutter speed and set
it with the camera.
Number of Flashes / Flash Frequency = Shutter Speed
For example, if the number of flashes is 10 and the firing frequency
is 5 Hz, the shutter speed should be at least 2 seconds.
● Stroboscopic flash is most effective with a highly reflective
subject against a dark background.
● Using a tripod and a remote control is recommended.
● A flash output of 1/1 and 1/2 cannot be set for stroboscopic flash.
● Stroboscopic flash can be used with “buLb”.
●
stroboscopic flash more than 10 times in succession.
To avoid overheating and deteriorating the flash head, do not use
Maximum Stroboscopic Flashes:
1/4
1/8
1/16
1/32
1/64
1/128
1
7
14
30
60
90
99
2
6
14
30
60
90
99
3
5
12
30
60
90
99
4
4
10
20
50
80
99
5
4
8
20
50
80
99
6-7
3
6
20
40
70
90
8-9
3
5
10
30
60
80
1/4
1/8
1/16
1/32
1/64
1/128
10
2
4
8
20
50
70
11
2
4
8
20
40
70
12-14
2
4
8
20
40
60
15-19
2
4
8
18
35
50
20-50
2
4
20
16
30
40
60-99
2
4
20
12
20
40
Flash
Output
Hz
Flash
Output
Hz
● Press MODE button so that
< MULTI > is displayed.
● Press the < SET >button to choose
the adjustable projects. (Blinking)
● Press the “-“or “+”button to adjust
the settings.

11. Protection Function
Over-Temperature Protection
To avoid overheating and degrading the flash head, do not fire
more than 20 continuous flashes at 1/1 full power. After 20
continuous flashes, allow at least 10 minutes for the camera flash
to cool down.
If you fire more than 20 continuous flashes and then fire more
flashes in short intervals, the over-temperature protection function
will be activated to make the recycling time about 10-15 sec. In
such case, give the camera flash about 10 minutes’ break to return
to normal.
When the over-temperature protection is started, the icon is
shown on the LCD display.
Power Output Level
1/1
1/2 +0.7
1/2 +0.3
1/2
1/4(+0.3,+0.7)
1/8(+0.3,+0.7)
1/16(+0.3,+0.7)
1/32(+0.3,+0.7)
1/64(+0.3,+0.7)
1/128(+0.3,+0.7)
Number of Flashes
20
30
40
60
100
200
300
500
1000
Number of flashes that will activate over-temperature protection:
Power
1/1
1/2(+0.3,+0.7)
1/4(+0.3,+0.7)
1/8(+0.3,+0.7)
1/16(+0.3,+0.7)
Times
10
15
20
30
40
Number of flashes that will activate over-temperature protection
in high-speed sync triggering mode:
7. S1 Mode
Press Slave Selection Button to enter S1 mode. In this mode, the
camera flash can function as a slave flash for creating multiple
lighting effects. It is respectively applicable to manual flash
environment. With this function, the flash will fire synchronously
when the main flash fires, the same effect as that by the use of
radio triggers.
8. S2 Mode
Press Slave Selection Button to enter S2 mode. In this mode, the
camera flash can function as a slave flash for creating multiple
lighting effects. It is respectively applicable to TTL flash
environment. With this function, the flash will ignore a single
“preflash” from the main flash and will only fire in response to the
second, actual flash from the main unit.
9. Sync Trigger Function
The Sync Cord Jack is a Φ3.5mm plug. Insert a trigger plug here
and the flash will be fired synchronously with the camera shutter.
Operation Instructions
1. Press C.Fn button to enter
custom setting state.
2. Press “-” or “+”button to
adjust the sleep time.
3. Press C.Fn button to return.
*Press any button to wake it up.
*Please set a short sleep period
if you do not use the flash,
which extends the working
time of the flash.
1. Press C.Fn button to enter
custom setting state.
1. Press “SET” button to enter
“bL” adjustment state.
3. Press the “-” or “+”button to
adjust the settings.
4. Press C.Fn button to return.
Signal
SL
bL
Function
Sleep Time
Setting
Backlight
Setting
Settings & Description
Settable time:
<3>3 min.
<10>10 min.
<30>30 min.
<60>60 min.
<OF> OFF
Press the button to control
backlight setting:
<ON>：Consecutive lighting
<12>：Lighting for 12 sec.
<OF>：Off
10. C.Fn: Setting Custom Functions
6. High-Speed Sync
●
● High Speed Sync (FP flash) enables the flash to synchronize with
all camera shutter speeds. This is convenient when you want to
use aperture priority for fill-flash portraits.
Note:
● The FP flash function can only work properly with the high-
speed remote control (e.g. Godox product CELLS II).
● High-speed sync function cannot be achieved when the flash is
set on the camera’s hotshoe.
Press MODE button makes the flash enter manual mode.
●
high-speed sync flashes, and its recycle time is 10 seconds slower
than the normal time.
Over-temperature protection may be activated after 10 consecutive

VI Maintenance
●
detected.
● Avoid sudden impacts and the product should be dedusted
regularly.
● It is normal for the flash tube to be warm when in use. Avoid
continuous flashes if unnecessary.
● Maintenance of the flash must be performed by our authorized
maintenance department which can provide original accessories.
● This product, except consumables e.g. flash tube, is supported
with a one-year warranty.
● Unauthorized service will void the warranty.
● If the product had failures or was wetted, do not use it until it is
repaired by professionals.
● Changes made to the specifications or designs may not be
reflected in this manual.
Shut down the device immediately should abnormal operation be
Model
Power
Guide No. (m ISO 100)
Vertical rotation angle
Horizontal rotation angle
Color temperature
Recycle time
Flash duration
Multi Flash
Dimension
Net weight
TT660II
4*AA batteries: LR6 alkaline or
Ni-MH rechargeable batteries (preferred)
58(1/1 ZOOM 105mm)
-10-90 degrees
0-270 degrees
5600k±200k
Approx. 0.1~5s (AA alkaline batteries used)
1/300s-1/20000s
1~99times; 1~99Hz
83mm*154mm*112mm
380g
V. Technical Data
Accessories:
1-Flash unit 1-Protecting bag 1-Mini stand
1-Instruction manual
说 明 手 册
在使用本产品之前，请先仔细阅读本手册，以确保您能安全使
用。请保存好本手册以备将来查询参考。
感谢您购买神牛产品。
神牛机顶闪光灯TT660 II，适用于各种品牌中带标准热靴的单反
相机，包括佳能、尼康、宾得、奥林巴斯等。产品具有以下亮点：
● 功率调节范围大(1/1~1/128), 22级精确微调, 光效把握更随心
● 色温恒定，全程保持5600±200K
● 支持频闪，S1/S2光控引闪等
● 使用专配遥控器，可实现高速同步功能。
前言
中英文双语 / Chinese English Bilingual
Electronic Camera Flash
IV. Advanced Application
1. Bounce Lighting
When taking photos, you can point the flash head toward a wall or
ceiling to bounce the light off the surface before illuminating the
subject. This can soften shadows behind the subject for a more
natural-looking shot.
2. Creating a Catchlight
Pull out the reflection card and built-in wide panel from the flash
head at the same time and then push the built-in wide panel back.
With the reflection card, you can create a catchlight in the subject’s
eyes to add life to the facial expression. This function can reach
optimal effect when the flash head is 90° upwards.
3. Use the Wide Panel
Pull out the built-in wide panel to enlarge the flash lighting range,
so as to get more softened and natural lighting effect.

1. 请勿让本产品淋雨或受潮，以免发生火灾或触电。
2. 本产品内部有高压元件，切勿自行拆解或维修。如果接触产
品内部的高压电路，可能会发生触电。需要修理时，请送往指定
地点进行专业维修。
3. 在使用过程中，如果本产品由于跌落、受到挤压或遭受强烈
冲击而造成外壳破裂的，请勿继续使用，以免因接触到内部电子
元件而受到电击伤害。
4. 请勿在近距离将闪光灯头正对人眼闪光(特别是婴儿的眼睛)，
否则可能会在短时间内造成视力障碍。在使用闪光灯拍摄婴儿
时，建议闪光灯距离婴儿至少1米以上，也可以使用反射闪光来
减少闪光可能对视力造成的伤害。
5. 请勿在化学品、可燃性气体或其他特殊物质附近使用闪光
灯，这些物质在特殊情况下可能对闪光灯发出的瞬间强光敏感，
有可能导致火灾或电磁干扰。在这些场合下，请注意相关警告标
识。
6. 请勿将本产品放置在超过50摄氏度的环境下，否则可能对元
器件造成损坏。
7. 本产品不能防水，在雨天及潮湿环境下请注意防水。
一、部件名称
警告
广角扩散板
闪光灯头
光控接收器
快充插座
快充座盖
同步插孔
热靴座 热靴触点
微型底座
固定旋扭
眼神光板
可选购附件：
为了获得最佳的拍摄体验和光效创意，可选购附件：电源盒PB960、小蜂巢、色
片等。
MODE闪光模式
ON/OFF电源开关
LCD显示屏
ZOOM 变焦按钮
C.Fn用户自定义
上调按钮
SET设置
TEST试闪/回电指示灯
使用4节AA型电池。
(一)、安装电池
1、打开电池仓盖。
● 用您的拇指按电池仓盖，然后滑
动电池仓盖将电池仓盖打开。
2、安装电池。
● 按电池仓中的指示确保电池的正
负触点朝向正确。
3、关闭电池仓盖。
● 按箭头所示方向滑动电池仓盖将
其关闭。
二、安装
●
电池接触不良。
● 如果在连续闪光多次后更换电池，电池可能会很烫，请小心注意。
因为电池触点的外形不规则，使用碱性电池以外的AA型电池可能会导致
下调按钮
SLAVE光控选择
电池仓
充电时间和闪光次数
以AA型碱性电池(LR6)为例：
● 以上数据基于新的AA型碱性电池。
● 电池电量过低导致长时间无法充电时，显示屏上电池符合会闪烁，此时请更换电池。
充电时间
约0.1-5秒
闪光次数
约100-700
●
● 也可以使用AA型镍氢(Ni-MH)或锂电池。
请使用4节相同品牌的新电池。更换电池时，请同时更换4节。

您可以设置闪光频率(每秒的闪光次数，以Hz表示)、闪光次数
和闪光输出。
设置步骤：
计算快门速度：
在频闪闪光过程中，到闪光停止为止快门应保持开启状态。使
用下面的公式计算快门速度，然后用相机进行设置。
闪光次数/闪光频率＝快门速度
例如，如果闪光次数是10，闪光频率是5Hz，快门速度则至少
为2秒。
注：
● 反光很强的被摄体在暗背景前使用频闪闪光更加有效。
● 推荐使用三脚架、遥控开关和外置电源。
● 闪光输出为1/1或1/2时不能设置频闪闪光。
● 频闪闪光时也可以使用“buLb”。
为防止闪光灯头过热并损坏，请勿执行连续10次以上的频闪闪
光连拍。
(二)、把闪光灯安装到相机上
1、安装闪光灯。
● 滑动闪光灯固定座使其完全插入
相机的热靴插座。
2、拧紧闪光灯。
● 旋转固定座上的固定旋钮，直到
锁定闪光灯。
3、取下闪光灯。
● 旋转固定座上的固定旋钮，直到
闪光灯解除锁定。
1. 电源管理
ON/OFF电源开关控制TT660 II的打开和关闭，长时间不使用时
请关闭电源。
2. 功率选择
您可以在1/128功率至1/1全功率间以1/3档为增量设置闪光输
出。为获得正确的闪光曝光，请使用手持的闪光测光表确定所需的
闪光输出。
调节上/下调按钮可以调节闪光输出功率。
● M模式：从1/128功率至1/1全功率间以1/3档为增量设置闪
光输出；
● Multi模式：1/128功率至1/4全功率间以1档为增量设置闪光
输出；
● 手动高速模式：从1/16功率至1/1全功率间以1/3档为增量设
置闪光输出；
3. ZOOM设置闪光覆盖范围
● 手动设置闪光覆盖范围以匹配24 - 105毫米的镜头焦距。
● 按ZOOM键按钮，按上/下按钮可以调节ZOOM值。
注：设置闪光覆盖范围，确保其覆盖镜头焦距，这样照片就不会出现阴影边
缘。
4. M普通模式
通过按MODE模式选择按钮，可以使闪光灯进入M模式。M模
式下，闪光灯可以安装到相机或触发器热靴上进行引闪。拍摄时，
您只需要设定闪光输出，调整相机并按下快门，闪光灯会在相机同
步信号下进行闪光。
5. Multi频闪模式
通过按MODE模式选择按钮，可以使闪光灯进入Multi模式。
Multi模式下，使用频闪闪光，可以发出一系列快速的闪光。它可以
在一张照片上拍摄移动物体的多个图像。
三、使用闪光灯
最大频闪闪光次数
1/4
1/8
1/16
1/32
1/64
1/128
1
7
14
30
60
90
99
2
6
14
30
60
90
99
3
5
12
30
60
90
99
4
4
10
20
50
80
99
5
4
8
20
50
80
99
6-7
3
6
20
40
70
90
8-9
3
5
10
30
60
80
闪
光输出
Hz
1/4
1/8
1/16
1/32
1/64
1/128
10
2
4
8
20
50
70
11
2
4
8
20
40
70
12-14
2
4
8
20
40
60
15-19
2
4
8
18
35
50
20-50
2
4
20
16
30
40
60-99
2
4
20
12
20
40
闪
光输出
Hz
● 按下MODE模式选择按钮，
显示“Multi”。
● 按Set按钮选择调节项目
(闪烁)。
● 按上/下按钮调整数值。

功率
1/1
1/2(+0.3,+0.7)
1/4(+0.3,+0.7)
1/8(+0.3,+0.7)
1/16(+0.3,+0.7)
次数
10
15
20
30
40
7. S1光控
通过按SLAVE按钮，可以使闪光灯进入S1模式。S1模式下，闪
光灯可作为副灯使用，创造多种照明效果，适用于手动闪光环境。
它会与主闪光灯的第一次闪光同步触发闪光，效果与使用无线引闪
器一致。
8. S2光控
通过按SLAVE按钮，可以使闪光灯进入S2模式。S2模式下，可
以做副灯使用，适用于TTL闪光环境。具有防预闪功能，使用带一次
预闪功能的相机能用光控实现同步拍摄。它会与主闪光灯的第二次
闪光同步触发闪光，即2次光控引闪。
9. 同步插孔触发
同步插孔规格为Φ3.5mm，此处可插入同步线或者触发器触发
插头对闪光灯进行同步引闪。
10. C.Fn自定义功能
高速同步模式下，连续闪光热保护对应表：
操作说明
1. 按C.Fn按钮进入自定义设置状态；
2. 按上下按钮调节睡眠时间；
3. 按C.Fn按钮返回。
● 按任意按键可唤醒；
● 无需要时请设置短的睡眠时间，
这可以延长闪光灯的工作时间！
1. 按C.Fn按钮进入自定义设置状态；
2. 按 "SET" 键进入 "bL" 调整状态；
3. 按上下按钮可调节；
4. 按C.Fn按钮返回。
设置与说明
可设置时间：
<3>3分钟
<10>10分钟
<30>30分钟
<60>60分钟
<OF>无(OFF)
当操作按钮时，背
光点亮可设置为：
<ON>：持续点亮
<12>：点亮12秒
<OF>：熄灭
功能
睡眠时间设置
背光设置
符号
SL
bL
功率
1/1
1/2 +0.7
1/2 +0.3
1/2
1/4(+0.3,+0.7)
1/8(+0.3,+0.7)
1/16(+0.3,+0.7)
1/32(+0.3,+0.7)
1/64(+0.3,+0.7)
1/128(+0.3,+0.7)
次数
20
30
40
60
100
200
300
500
1000
连续闪光保护对应表：
四、 拍摄技巧
使用反光拍摄
如觉得直射光线太强，可将闪光灯灯头指向墙壁或天花板，此
时闪光在照亮被摄体前被墙面反射，这可减轻被摄物体背后的阴
影，获得更自然的摄影效果。
使用眼神光板拍摄
先将内置眼神光板和广角扩散板从灯头拉出，将广角扩散板推
回。此时使用本产品拍摄，可以在主体的眼睛造成高光点，使眼睛
更加迷人(眼神光)，此功能在闪光灯头上仰90度时能达到最好的效
果。
使用广角扩散板拍摄
拉出广角扩散板，使闪光范围扩大，闪光效果将更加柔和自
然。
6. 高速同步模式
●
● 使用高速同步(FP闪光)，您可以在所有的快门速度下同步使用闪光
灯。高速模式下，使用光圈优先对人像进行填充闪光时特别方
便。
注： 高速同步模式必须配合高速同步遥控器(比如神牛产品CELLS II)才可实现其
功能。
● 插在相机热靴上无法实现高速同步功能。
为防止闪光灯头过热并损坏，连续执行10次高速同步闪光后,系
统会自动进入热保护:回电时间会比正常延时10秒。
通过按MODE模式选择按钮，可以使闪光灯进入手动 模式。
●
11. 保护功能
热保护：
为防止闪光灯头过热并损坏，请勿在1/1功率时进行超过20次的
快速连续闪光。20次连续闪光后，要让闪光灯至少冷却10分钟。
如您在进行超过20次连续闪光后马上继续进行更多次闪光，内
部的防过热功能可能会被激活，使充电时间变为10至15秒。如果发
生这种现象，请让闪光灯冷却约10分钟，闪光灯便会恢复正常。
热保护启动后，显示屏上 符号会闪烁。

六、维护保养
●
● 灯体应避免震动，平时注意表面除尘。
● 灯体稍有发热为正常现象，无特别需要时，勿连续引闪。
● 闪光灯的所有维修概由本厂指定可供原厂配件之维修部负责。
● 1年保修，由于灯管为消耗品，不在1年保修范围。
● 经发现，擅自检修此闪光灯的，将取消闪光灯之一年保修期，维
修需要收取相关费用。
● 如果本品出现故障或者被水淋湿，在专业人员维修后方可继续使
用。
● 如有技术更改，恕不另行通知。
闪光灯在工作时，如发现异常，应立即关掉电源，查明原因。
型号
电源
最大闪光指数(m ISO 100)
上下旋转角度
左右旋转角度
色温
回电时间
闪光持续时间
频闪闪光
体积
净重
TT660 II
4节AA型碱性电池(LR6类型)
AA型镍氢(Ni-MH)电池
58(1/1 ZOOM 105mm)
-10°-90°
0-270°
5600K±200K
约0.1至5秒(AA型碱性电池)
1/300s－1/20000s
1~99次; 1~99Hz
83x154x112毫米
约380克
五、规格参数
所含物品
闪光灯……(1) 保护袋……(1) 微型底座…(1) 说明书……(1)