gofanco HDbitTv2 User manual

HDMI HDbitT CAT5e/6
Extender with IR - 120m
User's Guide
G4-0104A 1
P/N: HDbitTv2

2
Thank you for purchasing from gofanco. Our
products aim to meet all your connectivity needs
wherever you go. For optimum performance
and safety, please read the instructions carefully
and keep this User’s Guide for future reference. If
you need more information about our products,
please visit www.gofanco.com. For technical
support, pleaseemail usat [email protected].
For drivers/manuals download, please go to
http://www.gofanco.com/downloads.
Important Safety Notices
Please read safety instructions carefully before
installation and operation.
• Please pay close attention to all warnings
and hints for this device
• Do not expose this unit to rain, heavy
moisture, or liquid
• Do not repair the device or open the
enclosure without professional guidance to
avoid electric shocks. Doing so may void
your warranty
• Keep the product in a well-ventilated
location to avoid damage from overheating

3
• Shut off power and make sure environment
is safe before installation
• Do not plug the HDMI cables and IR cables
in/out when the device is in use to avoid
cable damage. Make sure they are plugged
into the correct ports
• Use the included DC5V power adapters
only. Make sure the specification matches if
using 3rd-party DC power adapters
Introduction
HDMI HDbitT CAT5e/6 Extender with IR -
120m extends high definition 1080P HDMI signals
from a source device to a display device up to 120
meters using one economical CAT5e/6 cable
with with IR support.
Package Contents
• HDMI HDbitT CAT5e/6 Extender with IR
- 120m (1 TX & 1 RX)
• IR Blaster and IR Receiver cables (1 each)
• Power adapter (2pcs)
• User guide

4
Features
• Extends HDMI audio/video signals up to
394ft (120m) over a single CAT5e/6 cable
• Supports resolutions up to 1080p@60Hz
• Direct one-to-one connection or one-to-
multiple over your Gigabit Ethernet switch
- additional RXs, part number HDbitTv2-
RX, sold separately
• Supports IR signal extension - control a
media player from a remote location with
the included IR Blaster and IR Receiver
cables
• Includes 2 power adapters to ensure a steady
flow of power and data transmission
Installation Requirements
1. HDMI source device (computer, DVD
player, XBOX, PS3, etc)
2. HDMI display device (SDTV/Monitor,
HDTV/Monitor, projector, etc.)
3. UTP/STP CAT5e/6 cable following
IEEE-T568B wiring standard

5
Product Layout
Figure 1: Transmitter (TX)
1. Reset: Press to reset the Transmitter
2. HDMI In: Connects to your HDMI source
with an HDMI cable (cable not included)
3. IR Out: Connects to the IR Blaster cable
4. Power Jack: Connects to the included power
adapter
5. Power LED: On when the Transmitter is
powered
6. RJ45 Out: Connects to the RJ45 of the
Receiver using a Cat cable
7. Data LED: Blinks during data transmission
8. Link LED: On when Cat cable is connected/
linked properly to Transmitter's and
Receiver's RJ45

6
Figure 2: Receiver (RX)
1. Reset: Press to reset the Receiver
2. HDMI Out: Connects to your HDMI display
with an HDMI cable (cable not included)
3. IR In: Connects to the IR Receiver cable
4. Power Jack: Connects to the included power
adapter
5. Power LED: On when the Receiver is
powered
6. RJ45 In: Connects to the RJ45 of the
Transmitter using a Cat cable
7. Data LED: Blinks during data transmission
8. Link LED: On when Cat cable is connected/
linked properly to Transmitter's and
Receiver's RJ45

7
Hardware Installation
1. Power off all devices including your HDMI
source and HDMI display(s).
2. Connect your HDMI source device to the
Transmitter's HDMI Input connector with
an HDMI cable (HDMI cable not included).
CAT Cable Wiring
We suggest both RJ45 connectors be wired
identically using T568B wiring standard for the
best performance and compatibility.

8
3. Optional: Connect the IR Blaster cable to
the Transmitter's IR Output port. Face the
eye towards your HDMI source device's IR
window. This connection is needed only if
you need to control your HDMI source
from the remote location.
4. Plug your CAT5e/6 cable between the
Transmitter's RJ45 Output and Receiver's
RJ45 Input.
5. Connect your HDMI display to the
Receiver's HDMI Output connector with a
HDMI cable (HDMI cable not included).
6. Optional: Connect the IR Receiver cable to
the Receiver's IR Input port. This connection
is needed only if you need to control your
HDMI source device from the remote
location.
7. Plug the included power adapters into the
Transmitter's and Receiver's power jacks,
thenplug bothpower adaptersinto areliable
power source.
8. Power on all connected devices.
9. The HDMI extender is ready for use.

9
Application
1-to-1 Connection
Direct connection between the TX and RX or
through a Gigabit LAN via a Dedicated Gigabit
Switch. If deployed within an existing network,
create a VLAN to segregate our devices (TX and
RX) from the rest of the network devices.
1-to-1 LAN Connection
1-to-1 Direct Connection

10
1-to-Many Connection
A Dedicated Gigabit Switch is recommended. If
deployed within an existing network, create a
VLAN to segregate our devices (TX and RX's)
from the rest of the network devices.
Notes:
- Many-to-Many Connection: A Smart Switch is
required. Create a separate VLAN for each TX
and its corresponding RX's. Each VLAN can
only have 1 TX.
- Additional RXs, part number HDbitTv2-RX,
sold separately.