gofanco HDMIExt2 User manual

HDMI CAT5e/6 Extender with
IR - 50m
User's Guide
G4-0034A
P/N: HDMIExt2

2
Thank you for purchasing from gofanco. Our
products aim to meet all your connectivity needs
wherever you go. For optimum performance
and safety, please read the instructions carefully
and keep this User’s Guide for future reference.
If you need more information about our
products, please visit www.gofanco.com. For
technical support, please email us at
[email protected]. For drivers/manuals
download, please go to http:/ww.gofanco.com/
download.
Important Safety Notices
Please read safety instructions carefully before
installation and operation.
• Please pay close attention to all warnings
and hints for this device
• Do not expose this unit to rain, heavy
moisture, or liquid
• Do not repair the device or open the
enclosure without professional guidance
to avoid electric shocks. Doing so may void
your warranty
• Keep the product in a well-ventilated
location to avoid damage from overheating

3
• Shut off power and make sure environment
is safe before installation
• Do not plug the HDMI cables and IR cables
in/out when the device is in use to avoid
cable damage. Make sure they are plugged
into the correct ports
• Use the included DC5V power adapters
only. Make sure the specification matches if
using 3rd-party DC power adapters

4
Transmitter (TX) (1pc) Receiver (RX) (1pc) User's Manual (1pc)
Power Adapter (2pcs) IR Blaster Extension
Cable (1pc)
IR Receiver Extension
Cable (1pc)
Introduction
The HDMI CAT5e/6 Extender with IR - 50m
extendshighdefinition1080pHDMIsignalsfrom
a source device to a display device up to 50
meters using an economical CAT5e/6 cable.
Features
• TransmitsHDMIsignalsfromsourcedevice
to display device up to 50 meters using
economical CAT5e/6 cabling
• Supports IR remote control function to
control the source device from long
distances
• Easy and clean installation
PackageContents

5
Installation Requirements
1. HDMI source device (computer, DVD
player, XBOX, PS3, etc)
2. HDMI display device (SDTV/Monitor,
HDTV/Monitor, projector, etc.)
3. UTP/STP CAT5e/6 cable following
IEEE-568B wiring standard
Product Layout
Figure 1: Transmitter (TX)
1. HDMI Out Connects to a local HDMI display
2. Link LED Lights up when HDMI input signal detected
Flashes when no HDMI input signal detected
3. HDMI Input Connects to the HDMI source device
4. IR Output Connects to the IR Blaster extension cable
5. RJ45 Output Connects to the Receiver's RJ45 Input port
using a CAT5e/6 cable
6. Reset Button Press the button to reset the transmitter
7. Power Jack Connects to the included power adapter

6
Figure 2: Receiver (RX)
1. Reset Button Push the button to reset the receiver
2. RJ45 Input Connects to the Transmitter's RJ45 Output
port using a CAT5e/6 cable
3. Link LED Lights up when RJ45 from TX detected
Flashes when RJ45 from TX not detected
4. Power Jack Connects to the included power adapter
5. HDMI Out Connects to remote HDMI display
6. IR Input Connects to the IR receiver extension cable
Hardware Installation
1. Power off all devices including your HDMI
source and HDMI display(s).
2. Connect your HDMI source device to the
Transmitter's HDMI Input connector with
an HDMI cable (HDMI cable not included).
3. Optional: Connect a HDMI display to the
Transmitter's HDMI out connector with an
HDMI cable (HDMI cable not included) for
local monitoring of the HDMI signal.

7
4. Optional: Connect the IR Blaster Extension
Cable to the Transmitter's IR output port.
Face the eye towards your HDMI source
device's IR window. This connection is
needed only if you need to control your
HDMI source from the remote location.
5. Plug your CAT5e/6 cable between the
Transmitter's RJ45 Output and Receiver's
RJ45 Input.
6. Connect your HDMI display to the
Receiver's HDMI ouput connector with a
HDMI cable (HDMI cable not included).
7. Optional:ConnecttheIRReceiverExtension
Cable to the Receiver's IR input port. This
connection is needed only if you need to
control your HDMI source device from the
remote location.
8. Plug the included power adapters into the
Transmitter's and Receiver's power jacks,
then plug both power adapters into a
reliable power source.
9. Power on all connected devices.
10. The HDMI extender is ready for use.

8
Application
Transmitter (TX)
Receiver (RX)
CAT5e/6 Cable
IR Blaster
Extension Cable
IR Receiver Extension Cable
HDMI Out
HDMI Out
HDMI In
Display
Display
DVD

9
FAQ & Solutions
Q: There is no video output or audio and
video display is not normal:
A: 1) Press the Receiver's reset button to reset
the unit.
2) Use a shorter network cable.
Q: The Receiver's Link LED is flashing:
A: 1) Make sure the network cable follows the
IEEE-568B wiring standard.
2)CheckwhetherTXhasHDMIsignalinput.
3) Reset both TX & RX and reconnect.
Q: The extender is not working properly:
A: 1) Please check the cable lengths below:
- HDMI cables: Up to 5m
- Network cables (CAT5e/6): Up to 50m
2) Press the reset button on the TX/RX and
reconnect.
Q: RX Link LED is on but there is no image:
A: 1) Press RX reset button to reset the unit.
2) Make sure the HDMI cable is firmly
connected to the display.
3) Use a higher quality network cable.

10
Specifications
Item Specifications
HDMI Compliance 1.4a
HDCP Compliance 1.2a
Video Bandwidth 225MHz (10.2Gbps)
Resolution
480i@60Hz, 480p@60Hz, 576i@50Hz,
576p@50Hz, 720p@50/60Hz,
1080i@50/60Hz, 1080p@50/60Hz
Audio Support PCM, AC3, DTS
Input TMDS Signal 1.2Vp-p
Loop-out on TX One HDMI loop-out on TX
IR Passback Yes
IR Frequency Range 20KHz-60KHz
Operating Temperature 32° - 140° F (0° - 60° C)
Power Adapter Output: 5VDC/2A
Power Consumption TX: <3W / RX: <2W
Product Dimensions 2.8" (L) x 2.6" (W) x 0.97" (H)
Weight TX: 0.18 lbs / RX: 0.17 lbs
Color Black