Gold Apollo AL-924 Operating instructions

Alpha-Numeric Display Pager
MODEL：
：：
：AL-924

PAGER PROGRAMMING SOFTWARE
Contents
April 12, 2007 V1.0
AL924
Contents
GETTING STARTED .................................................................................................................................................................. 1
E QUIPMENT R EQUIRED ............................................................................................................................................................... 1
E QUIPMENT S ETUP ..................................................................................................................................................................... 1
INSTALLING PROGRAMMER SOFTWARE......................................................................................................................... 3
I NSTALLATION ............................................................................................................................................................................ 3
R UNNING .................................................................................................................................................................................... 6
AL924 PROGRAMMING ........................................................................................................................................................... 7
I NTRODUCTION ........................................................................................................................................................................... 7
S TARTING THE P ROGRAMMER ..................................................................................................................................................... 7
M AIN M ENU ............................................................................................................................................................................... 9
M ENU BAR .................................................................................................................................................................................. 9
C ODE AND F EATURES ................................................................................................................................................................ 11
Frequency.............................................................................................................................................................................11
Capcode (Decimal Address)................................................................................................................................................ 12
Auto Increase 1 after write.................................................................................................................................................. 14
A LERT AND S TATUS .................................................................................................................................................................. 15
Alerts and Status ................................................................................................................................................................. 15
Manu Of Pager ................................................................................................................................................................... 18
Manual Write....................................................................................................................................................................... 19
Prompts............................................................................................................................................................................... 19
P ROMPTS E DIT .......................................................................................................................................................................... 20

PAGER PROGRAMMING SOFTWARE
Getting Started
April 12, 2007 1
AL924
Getting Started
The AL924T Pager Programming software, provides the flexibility to programAL924
pagers to meet individual requirements. To obtain the best results from the product,
please take a few minutes to read this instruction guide.
Equipment Required
To install and operate the programmer, you need a system that meets the following
minimum requirements:
1. An personal computer (PC) with printer port, or compatible
2. Windows 98 SE or above operating system (XP Recommended)
3. 256 MB of RAM
4. AL924 Programmer
5. An USB cable
6. AL924 Pager Programming Software
Equipment Setup
Refer to Figure 1 while performing the follows:
1. At the rear of the PC, connect the USB cable to the USB port on your computer.
2. Plug end of the USB cable into the AL924 programmer.
3. Hardware installation is complete.

PAGER PROGRAMMING SOFTWARE
Getting Started
April 12, 2007 2
AL924
Figure
FigureFigure
Figure 1
1 1
1 Programmer Hardware Connections
Programmer Hardware Connections Programmer Hardware Connections
Programmer Hardware Connections

PAGER PROGRAMMING SOFTWARE
Installing Programmer Software
April 12, 2007 3
AL924
Installing Programmer Software
Installation
Install the programmer software into a PC as follows:
1. Uncompress the AL924T(USB)V50(NR).zip and save them in a temporary directory.
2. Double click the setup.exe file. Click on “Y”.
3. Click “Next” on the Welcome screen.

PAGER PROGRAMMING SOFTWARE
Installing Programmer Software
April 12, 2007 4
AL924
4. Enter your user information and click “Next”. (Note: you must enter at least a single
character "into the company field)
5. Choose where the program should be installed and click “Next”.

PAGER PROGRAMMING SOFTWARE
Installing Programmer Software
April 12, 2007 5
AL924
6. On the Select Program Folder screen choose where you would like the program to
show up in your start menu and click “Install”.
7. If you had installed USB driver then select reboot now and click “Finish” on the
setup complete screen.

PAGER PROGRAMMING SOFTWARE
Installing Programmer Software
April 12, 2007 6
AL924
8. If you did not install USB driver, click “OK” to install USB driver.
9. Please reboot your computer after USB driver and programming software installed.
Running
You now have the program installed. To run it from the Start menu/ Programs/ Gold
Apollo /AL924T Pager Programmer.

PAGER PROGRAMMING SOFTWARE
AL924 Programming
April 12, 2007 7
AL924
AL924 Programming
Introduction
Preparing a Pager for Reading or Programming:
2. Establish a computer hardware configuration.
3. Run the programming software of AL924.
4. A Power LED illuminates on the Programming Interface to indicate proper contact.
If the Power LED did not illuminate then you must check the configuration and
restart the programming software of AL924.
5. Align the pager contact pin holes with the contact pins of the AL924 Programmer.
6. Press down on the pager until it is tight in the fixture.
7. Turn the pager off or wait the pager until standby mode. The pager is now ready to
read or program.
Starting the Programmer
1. The application can be launched from Start →Programs →Gold Apollo →AL924T
Pager Programmer. The following window appears:
2. Input your password. If key in wrong password for 3 times, the system shuts off
automatically. If the password is correct, the following window appears：
：：
：

PAGER PROGRAMMING SOFTWARE
AL924 Programming
April 12, 2007 8
AL924
3. Now, the system examines that the AL924 programmer is well installed. If any
problems encountered, the following window appears:
4. Please re-check the AL924 programmer and printer port are well installed or not. If
connection succeeds with the AL924 programmer, the system enters the Main Menu.