Gold Apollo VP200 Operating instructions

Voice Pager
MODEL：
：：
：VP200

PAGER PROGRAMMING SOFTWARE
Contents
September 7, 2007 V1.4
VP200
Contents
CONTENTS...................................................................................................................................................................................0
GETTING STARTED ...................................................................................................................................................................1
E QUIPMENT R EQUIRED ............................................................................................................................................................... 1
P ROGRAMMING I NTERFACE ........................................................................................................................................................ 1
INSTALLING PROGRAMMER SOFTWARE..........................................................................................................................2
I NSTALLATION ............................................................................................................................................................................ 2
R UNNING .................................................................................................................................................................................... 5
CONNECTING PROGRAMMER TO VP200 ...........................................................................................................................6
VP200 PROGRAMMING ............................................................................................................................................................7
I NTRODUCTION ........................................................................................................................................................................... 7
S TARTING THE P ROGRAMMER .................................................................................................................................................... 8
M AIN M ENU ............................................................................................................................................................................... 9
Menu bar............................................................................................................................................................................... 9
Serial Setting....................................................................................................................................................................... 10
Serial No ............................................................................................................................................................................. 10
Tone System..........................................................................................................................................................................11
Channel................................................................................................................................................................................11
Setting ................................................................................................................................................................................. 14

PAGER PROGRAMMING SOFTWARE
Getting Started
September 7, 2007 1
VP200
Getting Started
The VP200 Pager Programming Software provides the flexibility to program VP200
pagers to meet individual requirements. To obtain the best results from the product,
please take a few minutes to read this instruction guide.
Equipment Required
To install and operate the programmer, you need a system that meets the following
minimum requirements:
An personal computer (PC), or compatible
Windows SE or above operating system (XP Recommended)
128 MB of RAM
A USB output port
Programming Interface
The Programming interface kit, shown in following Figure, supports VP200 programming
Items included with the interface kit consist of the following:
VP200 Programming software
VP200 Programmer
USB Cable - Type A to B
VP200 Programmer USB Cable - Type
A to B

PAGER PROGRAMMING SOFTWARE
Installing Programmer Software
September 7, 2007 2
VP200
Installing Programmer Software
Installation
Install the programmer software into a PC as follows:
1. Uncompress the VP200_Setup.zip and save them in a temporary directory.
2. Double click the setup.exe file. Click on “Y”.
3. Click “Next” on the Welcome screen.
4. Enter your user information and click “Next”. (Note: you must enter at least a single
character "into the company field)

PAGER PROGRAMMING SOFTWARE
Installing Programmer Software
September 7, 2007 3
VP200
5. Choose where the program should be installed and click “Next”.
6. On the Select Program Folder screen, choose where you would like the program to
show up in your start menu and click “Install”.

PAGER PROGRAMMING SOFTWARE
Installing Programmer Software
September 7, 2007 4
VP200
7. If you had installed USB driver then click “Finish” on the Setup Complete screen and
VP200 Pager Programmer has been installed on your computer.
8. If you did not install USB driver then click “OK” to install USB driver.

PAGER PROGRAMMING SOFTWARE
Installing Programmer Software
September 7, 2007 5
VP200
9. Please reboot your computer after USB driver and programming software installed.
Running
You now have the program installed. To run it from the Start menu/ Programs/ Gold Apollo
/VP200 Pager Programmer.

PAGER PROGRAMMING SOFTWARE
Connecting Programmer to VP200
September 7, 2007 6
VP200
Connecting Programmer to VP200
Refer to Figure then connect the programmer kit as follows:
1. At the rear of the PC, connect the USB cable Type A Male to the USB port.
2. Plug the USB cable Type B Male into USB connector of the VP200 programmer.
Hardware installation is complete.
Computer
VP 200
VP 200
Programmer
USB Cable Type
A to B
Figure Programmer Hardware Connections

PAGER PROGRAMMING SOFTWARE
VP200 Programming
September 7, 2007 7
VP200
VP200 Programming
Introduction
The following describes the procedures for using the VP200 programmer to accomplish:
1. Establish a computer hardware configuration.
2. Make sure VP200 has fully charged battery.
3. Turn the On/Off volume control to the OFF position.
4. Turn the function switch to position ‘C’.
5. With your right or left thumb, press down firmly and hold the reset button.
6. With your other hand, turn the On/Off volume control to ON.
7. The amber and red indicators should both light and a constant loud tone should sound
for three seconds at least, then pager enter the programming mode and release the
reset button.
8. Observe the position of the programming pins and insert the VP200 into the VP200
programming nest. The red indicator on the programming interface should light.
9. After programming succeeded, need to turn the On/Off volume control to the ON
position to effect the values.

PAGER PROGRAMMING SOFTWARE
VP200 Programming
September 7, 2007 8
VP200
Starting the Programmer
1. The application can be launched from Start →Programs →Gold Apollo →VP200
Pager Programmer. The following window appears:
2. Input your password. If key in wrong password for 3 times, the system shuts off
automatically. If the password is correct, the following window appears:
3. Now, the system examines that if the VP200 programmer is well installed. If any
questions, the following window appears:
4. The system shuts off automatically, please re-check the VP200 programmer and COM
port are well installed or not then, re-execute the system. If the connection with
programmer is OK, the system enters the Main Menu.