Gold Apollo TE-310 User manual

Models : TE-310 16KEY Transmitter
VHF UHF Transmitter
Product Name : Transmitter
Models : TE-310
GOLD APOLLO CO., LTD.
Rm 1, 3th F1.,No .77, Secretary. 1 , Hsin Tai Wu .,Rd.,
Hsi-Chih Hsien, Taiwan, R. O. C.
Tel : [phone]
Web site : http\\www.apollo.com

Models : TE-310 16KEY Transmitter
VHF UHF Transmitter
Product Name : Transmitter
Models : TE-310
GOLD APOLLO CO., LTD.
Rm 1, 3th F1.,No .77, Secretary. 1 , Hsin Tai Wu .,Rd.,
Hsi-Chih Hsien, Taiwan, R. O. C.
Tel : [phone]
Web site : http\\www.apollo.com

Attention
TE-310 Transmitter is used to page guests or staffs in a limited area,
especially suitable for factory, restaurant and hospital. The operation
is simple and friendly to keep good communication with your guests
and staffs.
There are 19 push buttons for your choice. Each button is able
to independently page a single person and also available to
page more than one person at the same time, as well. In
addition, it has the flash light as a reminder and also can repeat
paging the guests/staffs automatically when the one you page
has not shown up.
Transmitter
Be aware at following situations ,which will help to extend the life
cycle of transmitter.
NDon't change transmitter or tamper with its original
appearance.
NDon't put transmitter close to a heat source or in light
direct sun.
NDon't put transmitter in dust , moisture or on uneven surface.
NDon't soak transmitter into the water.
NNever operate the device with out the correct Gold Apollo
antenna , or a suitable artificial load , connected.
Function \ Location
Function \ Location
PWRTX
F3F2F1
1 9
102
311
12
4
513
6 14
15
7
8 16
1. Antenna Connect (BNC 50 ohm)
2. Power Connect (8.4V/1.5A)
3. RS232 D-SUB (FEMALE 9PIN)
1
2
3
Outlook
2.PWR(Orange) Power LED
1.TX (Rad) Transmit LED
1 2
44. RJ-11 Telephone Jack To Cancer
parer.

Attention
TE-310 Transmitter is used to page guests or staffs in a limited area,
especially suitable for factory, restaurant and hospital. The operation
is simple and friendly to keep good communication with your guests
and staffs.
There are 19 push buttons for your choice. Each button is able
to independently page a single person and also available to
page more than one person at the same time, as well. In
addition, it has the flash light as a reminder and also can repeat
paging the guests/staffs automatically when the one you page
has not shown up.
Transmitter
Be aware at following situations ,which will help to extend the life
cycle of transmitter.
NDon't change transmitter or tamper with its original
appearance.
NDon't put transmitter close to a heat source or in light
direct sun.
NDon't put transmitter in dust , moisture or on uneven surface.
NDon't soak transmitter into the water.
NNever operate the device with out the correct Gold Apollo
antenna , or a suitable artificial load , connected.
Function \ Location
Function \ Location
PWRTX
F3F2F1
1 9
102
311
12
4
513
6 14
15
7
8 16
1. Antenna Connect (BNC 50 ohm)
2. Power Connect (8.4V/1.5A)
3. RS232 D-SUB (FEMALE 9PIN)
1
2
3
Outlook
2.PWR(Orange) Power LED
1.TX (Rad) Transmit LED
1 2
44. RJ-11 Telephone Jack To Cancer
parer.

25
Operation
1. Frequency range : 147~170MHz,
450~470MHz.
2. Modulation Type : F S K
3. Channel spacing : 12.5 / 25MHz
4. Output power (ERP): 1W
5. Maximum deviation: +/-4.5KHz
6. Harmonic Radiation : less - 25dBm
7. Frequency stability : 2.5ppm at -10C~60C
8. Output Connect : BNC (F)
9. Current Consumption :
Standby : 100mA ; Transmit : 400mA
7. Dimensions : 23.2 (W)*50 (H)*17(D)
8. Weight : 650g ( No Antenna )
SystemSpecifications
SystemSpecifications INSTRUCTION FOROPERATION:
1.Activate paging:
Press any button among these 50 push buttons, the light will flash
and enter active mode, then send the signal out.
uTo repeat paging : In the active mode, it can be programmed to
send the same message every 30 sec. or 45 sec, or 60 sec, or 2
minutes, or 5 minutes or continuo
vTo page more than one person :
More than one button can be activated at the same time to page
more than one person.
wLED Sign Display:
It's an option on the software.
When the button is pressed, it will activate to send the signal
and show the number on the LED Display at the same time.
The numbers on the Display will be arranged by sequence, the
first number always shows up firstly. , 30 minutes ,

25
Operation
1. Frequency range : 147~170MHz,
450~470MHz.
2. Modulation Type : F S K
3. Channel spacing : 12.5 / 25MHz
4. Output power (ERP): 1W
5. Maximum deviation: +/-4.5KHz
6. Harmonic Radiation : less - 25dBm
7. Frequency stability : 2.5ppm at -10C~60C
8. Output Connect : BNC (F)
9. Current Consumption :
Standby : 100mA ; Transmit : 400mA
7. Dimensions : 23.2 (W)*50 (H)*17(D)
8. Weight : 650g ( No Antenna )
System Specifications
SystemSpecifications INSTRUCTION FOROPERATION:
1.Activate paging:
Press any button among these 50 push buttons, the light will flash
and enter active mode, then send the signal out.
uTo repeat paging : In the active mode, it can be programmed to
send the same message every 30 sec. or 45 sec, or 60 sec, or 2
minutes, or 5 minutes or continuo
vTo page more than one person :
More than one button can be activated at the same time to page
more than one person.
wLED Sign Display:
It's an option on the software.
When the button is pressed, it will activate to send the signal
and show the number on the LED Display at the same time.
The numbers on the Display will be arranged by sequence, the
first number always shows up firstly. , 30 minutes ,

Controlbuttons
2. Stop paging:
In the active mode or Time out mode, pressing the same
button again to stop paging, at the same time the repeating
and the number on the LED sign will be cancelled.
3. "Time out" Message display:
Once the option of "Time Out " message display is enable,
the button will be flash after being pressed for a certain time,
and will also send the message to the assigned location or
person as a reminder
4. Heart Beat ( anti-theft):
After activate the option of " heart beat ", the transmitter will
send heart beat signal every 15 sec, 30 sec, 45 sec, 1 minute, 2
minutes, 4 minutes or 6 minutes. The time-gap is programmable.
1. Active mode: when the button is pressed , the light will be
turned on to enter the active mode, then the signal will be sent
and repeated, as well.
2. Stop mode: Re-pressing the button to turn off the light
represented " Stop mode ". Under the active mode or "Time Out
" mode, to press the button again can also enter stop mode.
3. Time Out mode: After repeating paging for a certain time,
the light of button will be flashing, then go to Time out mode,
Instruction for Flash Light:
Instruction for Flash Light
Operation

Controlbuttons
2. Stop paging:
In the active mode or Time out mode, pressing the same
button again to stop paging, at the same time the repeating
and the number on the LED sign will be cancelled.
3. "Time out" Message display:
Once the option of "Time Out " message display is enable,
the button will be flash after being pressed for a certain time,
and will also send the message to the assigned location or
person as a reminder
4. Heart Beat ( anti-theft):
After activate the option of " heart beat ", the transmitter will
send heart beat signal every 15 sec, 30 sec, 45 sec, 1 minute, 2
minutes, 4 minutes or 6 minutes. The time-gap is programmable.
1. Active mode: when the button is pressed , the light will be
turned on to enter the active mode, then the signal will be sent
and repeated, as well.
2. Stop mode: Re-pressing the button to turn off the light
represented " Stop mode ". Under the active mode or "Time Out
" mode, to press the button again can also enter stop mode.
3. Time Out mode: After repeating paging for a certain time,
the light of button will be flashing, then go to Time out mode,
Instruction for Flash Light:
Instruction for Flash Light
Operation

1. Activate screen: to set up basic configurations , such
as cap code and frequency from button No. 1 to button
No. 19
Instruction for programming:
Instruction for programming
Instruction for programming
2. To set up the cap codes and type from button No.
F1,F2,F3 . butt Please be sure to click " Canned " first to
type the content of message.

1. Activate screen: to set up basic configurations , such
as cap code and frequency from button No. 1 to button
No. 19
Instruction for programming:
Instruction forprogramming
Instructionfor programming
2. To set up the cap codes and type from button No.
F1,F2,F3 . butt Please be sure to click " Canned " first to
type the content of message.

3.Config :
ŒTIME OUT LED OFF : to enable this option, when it's time
out for a certain number, it will enter off mode after the
time out message is sent if there is a message
preprogrammed.
•BEEP OFF : to enable this option, this button has no beep
sound
ŽTime Out : to enable this option represent the button has
been pressed for a certain time and not been delete yet,
the light of button can be flash or send out the message to
an assigned location or person as reminder. It can be
programmable for 5 min, 10 min, 15 min, 30 min, or
disable.
3. Configuration Instruction:
Instruction for programming
Instructionforprogramming

3.Config :
ŒTIME OUT LED OFF : to enable this option, when it's time
out for a certain number, it will enter off mode after the
time out message is sent if there is a message
preprogrammed.
•BEEP OFF : to enable this option, this button has no beep
sound
ŽTime Out : to enable this option represent the button has
been pressed for a certain time and not been delete yet,
the light of button can be flash or send out the message to
an assigned location or person as reminder. It can be
programmable for 5 min, 10 min, 15 min, 30 min, or
disable.
3. Configuration Instruction:
Instructionforprogramming
Instructionfor programming

•TX Repeat time : to set up time-gap for repeating page
before Time out , it can be programmable for 30sec
retary , 45 sec, 60 sec, 2 min, 5 min or disable
•LED Msg, enable : to enable this option, the number you press
will be shown on the LED display.
‘LED SIGN CAPCODE: to set up the cap code of LED sign
display
’Head of LED Sign massage : the title displayed on the LED
Sign
“Timeout Msg. Enabl: to enable this option, the
preprogrammed message will be sent out when it's time up
”Head of Timeout message: the title displayed before the
Time out message.
4. Write: please see the above
In the main menu of the window to execute
the command of " To flash\Write" for programming
5. Read: please see the above
in the main menu of the window to execute the
command of "To Flash\Read" to read the data.
Instructionfor programming
Instructionfor programming

•TX Repeat time : to set up time-gap for repeating page
before Time out , it can be programmable for 30sec
retary , 45 sec, 60 sec, 2 min, 5 min or disable
•LED Msg, enable : to enable this option, the number you press
will be shown on the LED display.
‘LED SIGN CAPCODE: to set up the cap code of LED sign
display
’Head of LED Sign massage : the title displayed on the LED
Sign
“Timeout Msg. Enabl: to enable this option, the
preprogrammed message will be sent out when it's time up
”Head of Timeout message: the title displayed before the
Time out message.
4. Write: please see the above
In the main menu of the window to execute
the command of " To flash\Write" for programming
5. Read: please see the above
in the main menu of the window to execute the
command of "To Flash\Read" to read the data.
Instructionforprogramming
Instructionfor programming