Goldmedal 8123 User manual

Part No. 88174
Roller Grill
Model # 8123, 8123PE
Instruction Manual
Cincinnati, OH 45241-4807 USA

Roller Grill
Model 8123
2
SAFETY PRECAUTIONS
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle.
008_051514
DANGER
Improper installation, adjustment, alteration, service, or maintenance can
cause property damage, injury, or death. Any alterations to this equipment will
void the warranty and may cause a dangerous condition. NEVER make
alterations to this equipment. Read the Installation, Operating, and
Maintenance Instructions thoroughly before installing, servicing, or operating
this equipment.
014_051514
WARNING
To avoid burns, DO NOT touch heated surfaces.
DO NOT place or leave objects in contact with heated surfaces.
009_092414
WARNING
ALWAYS wear safety glasses when servicing this equipment.
010_010914
WARNING
No user serviceable parts inside. Refer servicing to qualified service
personnel.
011_051514
WARNING
Read and understand operator’s manual and all other safety instructions
before using this equipment. To order copies of the operator’s manual go to
gmpopcorn.com or write to Gold Medal Products Co., 10700 Medallion Drive,
Cincinnati, OH 45241 USA 1-(800)-543-0862
022_060215

Roller Grill
Model 8123
3
SAFETY PRECAUTIONS (continued)
WARNING
DO NOT allow direct contact of this equipment by the public when used in
food service locations. Only personnel trained and experienced in the
equipment operation may operate this equipment.
Carefully read all instructions before operation.
012_010914
WARNING
This machine is NOT to be operated by minors.
007_010914
Note: Improvements are always being made to Gold Medal’s equipment. This information
may not be the latest available for your purposes. It is critical that you call Gold Medal’s
Technical Service Department at -800-543-0862 for any questions about your
machine operations, replacement parts, or any service questions. (Gold Medal Products
Co. does not assume any liability for injury due to careless handling and/or reckless
operation of this equipment.)

Roller Grill
Model 8123
4
Installation Instructions
Inspection of Shipment:
After unpacking, check thoroughly for any damage which may have occurred in transit. Claims
should be filed immediately with the transportation company. The warranty does not cover
damage that occurs in transit, or damage caused by abuse, or consequential damage due to
the operation of this machine, since it is beyond our control (reference warranty in back of
manual).
Manual
Read and understand the operator’s manual and all other safety instructions before using this
equipment. To order copies of the operator’s manual go to gmpopcorn.com or write to Gold
Medal Products Co., 10700 Medallion Drive, Cincinnati, OH 45241 USA 1-(800)-543-0862.
Setup:
Remove all packing material and tape before starting operation.
Electrical Requirements:
The following power supply must be provided:
8123, 8123PE: 120 V~, 1740 W, 60 Hz
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle.
008_051514
Your electrician must furnish sufficient power for proper machine operation. We recommend this
equipment be on a dedicated and protected circuit. Failure to wire properly will void the warranty
and may result in damage to the machine. It is Gold Medal Products Co.’s recommendation that
this machine be plugged directly into a wall outlet. The use of extension cords is not
recommended due to safety concerns, and may cause sacrificed and/or reduced performance.
Make sure cord is located to prevent a trip hazard or unit upset.

Roller Grill
Model 8123
5
Before You Plug In Machine
1. Make sure all machine switches are in the OFF position before plugging the equipment
into the receptacle.
2. Make sure the wall outlet can accept the grounded plugs (where applicable) on the
power supply cord.
3. The wall outlet must have the proper polarity. If in doubt, have a competent electrician
inspect the outlet and correct if necessary.
4. DO NOT use a grounded to un-grounded receptacle adapter (where applicable).
5. Install the unit in a level position.
CAUTION
If the supply cord is damaged, it must be replaced by Gold Medal Products Co.,
its service agent or similarly qualified persons in order to avoid a hazard.
039_080614
Operating Instructions
Controls and Their Functions
On/Off Switch
Flipping this switch to the "ON" position energizes the motor that turns the rollers. This
switch can be used alone or with the heat turned on.
Heat Control
Turning this control counter-clockwise increases the amount of heat to the rollers. There
are 3 sets of these controls, 1 for each set of rollers.

Roller Grill
Model 8123
6
Care and Cleaning
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
DO NOT immerse in water.
Always unplug the equipment before cleaning or servicing.
025_020314
WARNING
To avoid burns, DO NOT touch heated surfaces.
DO NOT place or leave objects in contact with heated surfaces.
009_092414
Good sanitation practice demands that all food preparation equipment be cleaned regularly (only
use non-toxic, food grade cleaners). A clean looking, well-kept machine is one of the best ways of
advertising your product.
Follow the directions below to clean and sanitize the unit each day after use.
1. With the machine OFF, unplug the unit and allow it to cool before attempting to clean.
2. Remove any remaining hot dogs from the rollers.
3. Clean all rollers using a soft cloth dampened with a mild soap and hot water.
DO NOT use oven cleaners or abrasive materials (e.g. steel wool or abrasive pads) on
non-stick roller assemblies; ONLY clean with a soft cloth dampened with a mild soap
and hot water.
4. Remove the drip pan/accessories and clean thoroughly with mild soap and hot water.
5. Clean the outside of the unit using a soft cloth dampened with a mild soap and hot
water.
Wipe stainless steel parts with a clean cloth and cleaner designed for stainless steel,
such as Gold Medal Watchdog Stainless Cleaner (Item No. 2088).
DO NOT use oven cleaners or abrasive materials as they will damage parts of the
machine.
6. Dry the unit completely with a soft, dry cloth.
7. When unit is dry, reinsert the drip tray beneath the rollers.

Roller Grill
Model 8123
7
MAINTENANCE INSTRUCTIONS
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle.
008_051514
DANGER
Improper installation, adjustment, alteration, service, or maintenance can
cause property damage, inj
ury, or death. Any alterations to this equipment will
void the warranty and may cause a dangerous condition. NEVER make
alterations to this equipment. Read the Installation, Operating, and
Maintenance Instructions thoroughly before installing, servicing, or operating
this equipment.
014_051514
WARNING
No user serviceable parts inside. Refer servicing to qualified service
personnel.
011_051514
CAUTION
THE FOLLOWING SECTIONS OF THIS MANUAL ARE INTENDED ONLY
FOR QUALIFIED SERVICE PERSONNEL WHO ARE FAMILIAR WITH
ELECTRICAL EQUIPMENT. THESE ARE NOT INTENDED FOR THE
OPERATOR.
027_010914

Roller Grill
Model 8123
8
ORDERING SPARE PARTS
. Identify the needed part by checking it against the photos, illustrations, and/or
parts list.
2. Use only approved replacement parts when servicing this unit.
3. When ordering, please include part number, part name, and quantity needed.
4. Please include your model number, serial number, and date of manufacture (located on the
machine nameplate/data plate) with your order.
5. Address all parts orders to:
Parts Department
Gold Medal Products Co.
0700 Medallion Drive
Cincinnati, Ohio 4524 -4807
Or, place orders by phone or online:
Phone: [phone]
(5 3) 769-7676
Fax: [phone]
(5 3) 769-8500
E-mail: [email protected]
Web Page: gmpopcorn.com

Roller Grill
Model 8123
9
Knob, Control
P/N 38389
Switch, Rocker
–
Green
P/N 42532
4” Legs
P/N 84077
Medium Roller Assembly
(x18)
P/N 88232
Non-Stick Roller Assembly (x18)
P/N 88232PE
Right Side Plate Weldment
P/
N 88133
Left Side Plate Weldment
P/N 88134
Drip Tray
P/N 88097
Teflon Bearing (x36)
P/N 77918
O-Ring (x36)
P/N 87511
Front Control Sticker
P/N 88098

Roller Grill
Model 8123
10
Drive Chain
(x3)
P/N 88102
Master Link Drive
Chain (x3)
P/N 87044
Idler Sprocket
P/N 69824
Drive Sprocket
P/N 87353
Spring
P/N 68734
Middle/Back Idler Assy (x2)
P/N 68906
Idler Assy Front
P/N 68747
Positraction Sprocket (x15)
P/N 87988
Assembly Bracket Weldment
P/N 88053
Outer Retainer (x15)
P/N 88228
Conductor Plate (x6)
P/N 88056
Insulator Board (x3)
P/N 88055