GolfAchiever GA SIM User manual
GA SIM Platform Setup Guide
Platform components
Below are the components needed to successfully assemble the GA SIM platform
Turf for Spacer (1)
Metal Spacer (1)
GA Sim base locator (2) Screws ( )
Small front turf (2)
Small front rubber mat (2)
Large platform rubber mat (2)
Large platform turf (2)
Metal brackets (5)
Screws (10)
Turf Clips ( )
Base Protector Left/Right (2)
Revision B 12/8/2011
Warning & Disclaimer: The sport of golf can be dangerous and improper setup and application of your Gol-
f chiever unit can result in personal injury or property damage. USE AT YOUR OW RISK! Proper installation
and application will help to insure safety. Refer to the Platform Setup Guide for proper installation and usage. Focal-
tron assumes no liability regarding the improper installation, mishandling, or misapplication of products sold. The
installer or user is responsible for confirming proper installation and safety of application. Should there be any ques-
tions as to installation and application, Focaltron must be contacted. In no event will Focaltron be liable for any inci-
dental, special, or consequential personal injuries or property damages that arise from the use of the products sold by
Focaltron even if Focaltron has been advised of such injuries or damages. For further questions or setup assistance
contact Focaltron Customer support at: +1-408-530-8588 or support@golfachiever.com.
Step 1
Place the two largest black mats side by side with the GolfAchiever logo facing away from your desired hitting
direction as shown in the picture below. Use the supplied metal brackets to secure both rubber mats together. A
total of four metal brackets should be used.
The same should be
done on both sides of
the platform
Step 2
Install base locators in front of large black mats. For the black mat on the left side the base locator pegs should
be placed in the holes farthest to the left. For the black mat on the right side the base locator should be placed
farthest to the right.
Metal brackets should
be flush with black mat.
Use included screws to
secure each bracket to
the black mat.
Step 3
Once the locators are installed you can install the front small rubber mats. These rubber mats simply go over the
back pegs of the installed base locators. The last metal bracket will be used to clamp these two mats together
The same should be
done on both sides of
the platform
Step 4
Now you can install the large pieces of turf. Each piece of turf can be flipped to work with both the right and left
handed tee position. Be sure to place the turf correctly depending on your setup. The large black mats are each
marked with a R and L at the tee locations for Right and Left. It will also help to install the tee before laying
down the green turf. Also utilize the turf clips included with your product to keep the turf from rises and block-
ing the sensors of your Golf Achiever.
Pegs on black mat should fit into
holes on green turf. Arrows indi-
cate install location of turf clips.
Three on each side of the platform.
GA Platform Setup Guide
Step 5
Next you can install the long metal spacer as well as the front green turf. The position of the metal spacer de-
pends on your setup. The setup in this guide is for a right handed player.
The holes on the metal spacer
should line up with the gold
screw holes on the base locator.
Place the long skinny turf spacer
over the metal spacer.
The front green turf simply fit
over the pegs of the front black
mats
Step 6
Install your GA Sim unit by placing it into the open base locator. Be sure to properly align the azimuth pin with
the designated slot on the locator. Once the unit is in place install the green metal base protector. Removal of
the front green turf will make this installation easier. The metal protector should fit securely over the base arm.
Remove turf in front of unit to
make install of the unit and the
metal base protector easier.
Use included screws ( ) to secure
the base protector to the base
locator. Once installed replace
front turf to complete platform
assembly.
Completed platform assembly
Table of contents
