GoMax Electronics MX-3004F User manual

3G/HD/SD-SDI Quad-view Video
Processor
User Manual
rev: 150818
Made in Taiwan
MX-3004F

Safety and Notice
The MX-3004F 3G/HD/SD-SDI Quad-view Video Processor has been tested for conformance to
safety regulations and requirements, and has been certified for international use. However, like all
electronic equipments, the MX-3004Fshould be used with care. Please read and follow the safety
instructions to protect yourself from possible injury and to minimize the risk of damage to the unit.
●Follow all instructions and warnings marked on this unit.
●Do not attempt to service this unit yourself, except where explained in this manual.
●Provide proper ventilation and air circulation and do not use near water.
●Keep objects that might damage the device and assure that the placement of this unit is on a
stable surface.
●Use only the power adapter and power cords and connection cables designed for this unit.
●Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device
before cleaning.
TABLE OF CONTENTS
INTRODUCTION.................................................................................................................1
FEATURES.........................................................................................................................1
PACKAGE CONTENTS ......................................................................................................1
SPECIFICATIONS ..............................................................................................................2
PANEL DESCRIPTIONS.....................................................................................................3
HARDWARE INSTALLATION.............................................................................................4
CONNECTION DIAGRAM...................................................................................................5
OPERATION SOFTWARE..................................................................................................6
WARRANTY......................................................................................................................14

1
INTRODUCTION
The MX-3004F 3G/HD/SD-SDI Quad-view Video Processor is an advanced video processor for
multimedia presentations. It is an ideal solution for some application such as broadcasting, where up to
four SDI video signals must be displayed on a single display. It supports up to 4 SDI video inputs, of which
four can be outputted simultaneously with the desired display layout through software control, IR remote
or front panel. The advanced video processor allows you to manipulate output images, wherever
positions and whatever sizes you want for viewing four computers or four video signals or a combination.
The embedded processor converts signals from input sources to match the native resolution of
monitors, flat panel displays, projectors as well as user-selectable output settings up to WUXGA
(1920x1200). Dual outputs are provided in both digital (SDI) and digital (DVI) format, one is connected to
remote display and other is connected to on-site display for real time monitoring.
FEATURES
●Supports 3G/HD/SD-SDI video formats
●Input resolutions support interlaced or progressive video under SMPTE
●Dual outputs DVI (640x480 to 1920x1200) / SDI (720P, 1080P)
●Each SDI input channel has 1 re-clocked SDI loop-outs
●Adjustable size & position through software, IR remote and front panel
●Image parameters and layouts are automatically saved in flash memory and can be recalled for later
use
●User-selectable output settings, up to 1920x1200 (Only for DVI)
●Perfect as a video screen splitter, a video converter and a video switcher
●Firmware upgradable for support of new features and technology enhancements
●Software control through RS-232 or IP port.
●Control protocol available for customer proprietary design
●1U size
PACKAGE CONTENTS
●1x MX-3004F
●1x USB to RS-232 cable
●2x 1U rack mounting-ear
●1x Installation software CD
●1x UL 12V 5A power adapter
●1x UL AC power cord
●1x User Manual
●1x IR remote control (28 keys)

2
SPECIFICATIONS
Model Name
MX-3004F
Technical
Role of usage
Multiplexer / video processor
Dual output support
Yes [DVI &SDI]
Background video input
No
Video bandwidth
DVI/HDMI [165MHz]
SDI 3G/HD/SD
Video input support
480i / 576i / 720p / 1080i / 1080p
Input TMDS signal
1.2 Volts [peak-to-peak]
ESD protection
Human body model — ±12kV [air-gap discharge] & ±8kV [contact discharge]
PCB stack-up
4-layer board [impedance control — differential 100Ω; single 50Ω]
Input
4x SDI
Output
2x SDI + 1x DVI/HDMI
RS-232 connector
DE-9 [9-pin D-sub female]
DVI connector
DVI-I [29-pin female]
RJ-45 connector
WE/SS 8P8C
Rotary switch
Yes
DIP switch
Yes (for factory reset and firmware update)
Mechanical
Housing
Metal enclosure
Dimensions
[L x W x H]
Model
440 x 235 x 44mm [1'4” x 9.3” x 1.7”]
Package
526 x 318 x 156mm [1'7" x 12.5" x 6.1"]
Carton
543 x 335 x 344mm [1'8" x 13.2" x 1'1"]
Weight
Model
2.6kg [5.8 lbs]
Package
3.7kg [ 8.2lbs]
Fixedness
1U rack-mounting case with ears
Power supply
12V 5A DC
Power consumption
35 Watts (max)
Operation temperature
0~40°C [32~104°F]
Storage temperature
-20~60°C [-4~140°F]
Relative humidity
20~90% RH [no condensation]

3
PANEL DESCRIPTIONS
Front Panel
1. Output Resolution Button: Select output resolution
2. Label Button: Window’s label ON/OFF
3. Custom Layout 1-8: Save custom layout button
4. IR Sensor: IR sensor for receiving the IR commands from IR remote
5. Default Layout mode A: Select default layout ( ) or custom layout
6. Default Layout mode B: Select default layout ( , , , )
7. Input 1-4 Select Button: Select input source
Rear Panel
8. Power Switch: Power On/Off
9. RS-232: RS-232 control port
10. +12V DC: Connect to the +12VDC power supply unit.
11. Dip Switch: Switch the firmware update mode or factory reset mode (Switch ON)
12. Device ID: To identify between units
13. Mini-USB: For firmware update
14. Ethernet: Ethernet control port.
15. Outputs: 2 SDI outputs
16. Outputs: DVI output
17. Input 1-4: SDI inputs 1-4
18. SDI local loop out

4
HARDWARE INSTALLATION
Safety Precautions
1. To prevent fire or shock hazards, do not expose this device to rain or moisture.
2. The product should be placed more than one foot away from heat sources such as radiators, heat
registers, stoves, and other products (including amplifiers) that produce heat. In addition, do not cover
any material or devices on the top of the device.
3. Do not use immediately after moving from a low temperature to high temperature, as this causes
condensation.
4. Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious
injury to a child or adult and serious damage to the product.
5. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning.
6. Do not allow the same still picture to be projected for a long time or an abnormally bright video picture
to be projected. The video image could be burned in to the display device.
Installation Procedures
Unpacking
Remove the MX-3004F from the shipping container and examine it for any signs of shipping
damage or missing items (check with package contents above). All shipping items should be saved if the
product is to be moved or returned for service. Shipping unit back to dealers for service not in the original
box may result in voiding warranty or additional cost.
Placement
The unit uses convection to cool. A fan is not needed, so do not block the sides of this device or
stack another device on the top or bottom of the MX-3004F.
Connections
We recommend the highest quality cables for both input and output connections.
1. Switch off the MX-3004F and all devices that you want to connect.
2. Connect a monitor, a projector or other displays that comes with DVI / SDI inputs
3. Connect a device equipped with SDI output including SD/HD/3G to the BNC input connector of
MX-3004F.
4. Connect your computer with the MX-3004F by a 9-pin RS-232 cable or Cat.5e cable, and then install
the software.
5. Plug in AD power cord into AC power socket.
6. Execute the control software and establish the connection between PC/Laptop and MX-3004F.
7. For detailed software control operation, please refer to the software instruction section.

5
CONNECTION DIAGRAM

6
OPERATION SOFTWARE
Method A: IR Remote Control
Button
Function
Label
Border & Label on/off
Analog Clock
Analog Clock on/off
Digital Clock
Digital Clock on/off
Power on/off the device
Custom layout 1
Custom layout 1
Custom layout 2
Custom layout 2
Custom layout 3
Custom layout 3
Custom layout 4
Custom layout 4
Custom layout 5
Custom layout 5
Custom layout 6
Custom layout 6
Custom layout 7
Custom layout 7
Custom layout 8
Custom layout 8
PAP 1 Default layout PAP
PAP 2 Default layout PAP
PAP 3 Default layout PAP
PAP 4 Default layout PAP
Full Screen layout 1
Full Screen – Window 1
Full screen layout 2
Full Screen - Window 2
Full screen layout 3
Full Screen - Window 3
Full screen layout 4
Full Screen - Window 4

7
Method B: Software Control through RS-232 port / Ethernet port
System Requirement and Precautions
1. The device provides a software control program, Quartet, which runs under Microsoft
Windows 98, 2000, XP, Vista or 7 through the interface of RS-232 serial control.
2. Before you click the icon of the software, make sure you have secured the connection
between your computer COM port and the device and switched on the device with green LED
light.
Start the Operation Software
When you double-click the .exe file, the below dialog will pop-up. Connect the software via
RS-232 or TCP/IP.
*under Microsoft Windows 7, please right click the program icon to start up as an administrator
RS-232 mode: Use RS-232 to connect the port on device and computer. Select correct serial
COM port (Port Number) and click the Connect button.
Ethernet (TCP/IP) mode: Enter the device IP address and click the Connect button.
After the software control setting is completed, it will enter directly to control interface.

8
Control Interface
1. PAP Panel
Display and adjust the window size and position.
Control percent: 10~100% to set the PAP panel display/control
size.
Stretch: Fix the size ratio when the window is resizing.
PAP mode
Window 1 in full screen
Window 2 in full screen
Window 3 in full screen
Window 4 in full screen
1
2
3
4
5
6
7
8

9
2. Tool Bar list:
(1) Status: Get all information of the device and update this software state.
(2) Port Setting: Pop-up the “Port Setting” dialog, user can change the connecting way.
(3) Advance Setting: Set the no signal color, fade in/out effect, background picture,
window text, input text, OSD border, Clock, audio and factory reset.

10
Clock and Audio:
User can set up the position of clock and other audio control.
Factory Reset:
Click the button to do factory default reset. This default reset
process will take about 10~15 seconds and it will be initialized all setting to original
system state.

11
(4) Version: Read the software and firmware version.
3. Output Resolution:
Set the output resolution. When setting the different resolution, the parameters of PAP and
custom layout (position and size) will change accordingly.

12
4. Audio, analog clock and digital clock
5. Background picture:
6. Default layout and Custom layout:
Default layout: Use factory preloaded
video layouts.
Custom layout: Use custom pre-saved video layouts.
In this part, you can adjust the size and position of output screen. If you want to save
the layout, please right click to save this layout into device.
7. Window selection and input mapping
Assign arbitrary video input and adjust the order of windows

13
8. Window setting
Adjust the size, position or other settings of the specified window.

14
WARRANTY
The SELLER warrants the MX-3004F 3G/HD/SD-SDI Quad-view Video Processor free from
defects in the material and workmanship for 1 year from the date of purchase from the SELLER or an
authorized dealer. Should this product fail to be in good working order within 1 year warranty period, The
SELLER, at its option, repair or replace the unit, provided that the unit has not been subjected to accident,
disaster, abuse or any unauthorized modifications including static discharge and power surge. This
warranty is offered by the SELLER for its BUYER with direct transaction only. This warranty is void if the
warranty seal on the metal housing is broken.
Unit that fails under conditions other than those covered will be repaired at the current price of parts
and labor in effect at the time of repair. Such repairs are warranted for 90 days from the day of reshipment
to the BUYER. If the unit is delivered by mail, customers agree to insure the unit or assume the risk of loss
or damage in transit. Under no circumstances will a unit be accepted without a return authorization
number.
The warranty is in lieu of all other warranties expressed or implied, including without limitations, any
other implied warranty or fitness or merchantability for any particular purpose, all of which are expressly
disclaimed.
Proof of sale may be required in order to claim warranty. Customers outside Taiwan are responsible
for shipping charges to and from the SELLER. Cables and power adapters are limited to a 30 day
warranty and must be free from any markings, scratches, and neatly coiled.
The content of this manual has been carefully checked and is believed to be accurate. However, The
SELLER assumes no responsibility for any inaccuracies that may be contained in this manual. The
SELLER will NOT be liable for direct, indirect, incidental, special, or consequential damages resulting
from any defect or omission in this manual, even if advised of the possibility of such damages. Also, the
technical information contained herein regarding the MX-3004F features and specifications is
subject to change without further notice.