Gonet Systems GoBeam 6100 User manual

GoBeam 6100 Quick Installation Guide
UM000017 Rev 1.0
Components Included in the Package
Description Qty
AWall/Pole Bracket
1
BClamping Bracket
1
C‘L’ Adapter Wall/Pole Mount
1
D‘T’ Adapter Wall/Pole Mount
1
EHex Bolt M8x70
2
FHex Bolt M8x40
1
GHex Bolt M8x25
1
HFlat Washer M8
4
ISpring Washer M8
4
JNut M8
1
KSafety Cable
1
Description Qty
L Waterproof RJ45 connector 2
M Optional Power Injector
1
Grounding Kit
Ring Terminal 1
Ground Screw
1
N
Lock Washer
2
Optional Mesh Antenna Kit
Mesh Antenna
2
Omni Antenna L-Brackets
1
Screw M4
2
Flat Washer M4
2
Spring Washer M4
2
O
Antenna Cable 2

GoBeam 6100 Quick Installation Guide
UM000017 Rev 1.0
1. Assemble the ‘T’ or ‘L’ Adapter
Horizontal Installation
Assemble the ‘T’ Adaptor to the
GoBeam 6100 Unit.
Vertical Installation
Assemble the ‘L’ Adaptor to the
GoBeam 6100 Unit.
2. Install the Mounting Brackets
When mounting the GoBeam 6100, the pole or wall mounting must
support a minimum of 61.6 lbs (28 kg). In addition, the pole or wall
mounting must support the wind loads from the GoBeam 6100. For
example, the wind load at a wind velocity of 100 mph (160 km/h) is
24.2 lbs (11 kg) and the wind load at a wind velocity of 165 mph
(264 km/h) is 66.1 lbs (30 kg).
Lorsque vous montez la GoBeam 6100, le poteau ou le montage mural
doit supporter d'un minimum de 61.6 lbs (28 kg). En outre, le
montage sur le poteau ou sur le mur doit appuyer les surcharges dues
au vent de la GoBeam 6100 (par exemple, 24.2 lbs (11 kg) pour la
vitesse du vent de 100 mph (160 km/h), 66.1 lbs (30 kg) pour
l'énergie éolienne Vitesse de 165 mph (264 km/h)).
Narrow Pole (1”-1.75” diameter)
B
Pole
A
H
E
I
Normal Pole (1.75”-3” diameter)
Pole
A
E
B
H
I
Flat Washe
r
S
p
rin
g
Washe
r
Hex Bol
t
“T” Adapte
r
Flat Washe
r
S
p
rin
g
Washe
r
Hex Bol
t
“L” Adapte
r

GoBeam 6100 Quick Installation Guide
UM000017 Rev 1.0
Large Pole (larger than 3” diameter)
Stainless
Steel Hose
Clamp
A
Pole
Wall Mounting Bracket
Horizontal Pole Mounting Vertical Pole Mounting
3. Assembling the Optional Mesh Antennas
Attach each
antenna cable to
the L-bracket.
Mount the L-bracket to the unit.
Before screwing the bracket tight,
tilt it so that it is vertical.
Attach the other ends of the antenna
cable to terminals
B1 & B2.
Attach each mesh
antenna.
4. Installing the Safety Cable
1. Wrap the safety cable around the pole and
insert the mounting plate through the
cable loop.
2. Attach the mounting plate to the
GoBeam 6100 unit using the
hexagonal bolts.
Flat Washe
r
Spring Washe
r
Nu
t
Spring
Washer
Flat
Washe
r
Nu
t
Bolts
Safety
Cable

GoBeam 6100 Quick Installation Guide
UM000017 Rev 1.0
5. Ground the GoBeam 6100 Unit
Connect the 10 AWG
grounding cable before
connecting any other
cables. When removing
the GoBeam 6100, the
grounding cable should
be the last cable
removed.
Connecter la prise de terre 10 AWG avant de connecter tout autre câble.
Pendant la désinstallation du GoBeam 6100, la prise de terre doit être le
dernier câble retiré.
6. Connect the Ethernet PoE
Pin # Signal
1 Data
2 Data
3 Data
4 48V (+)
5 48V (+)
6 Data
7 48V (-)
8 48V (-)
7. Connect the 1Gbps Network Connection
When using 1Gbps Network connection
,
use the Eth 1000
port as shown.
Pin # Signal Color
1 BI_DA+ white & green
2 BI_DA- green
3 BI_DB+ white & orange
4 BI_DC+ blue
5 BI_DC- white & blue
6 BI_DB- orange
7 BI_DD+ white & brown
8 BI_DD- brown
Eth 1000
Port
1G Network
Cable