Gonet Systems GoBeam 5100 User manual

GoBeam 5100 Quick Installation Guide
UM000018 Rev 1.0
Components Included in the Package
Description Qty
AWall/Pole Bracket
1
BClamping Bracket
1
C‘L’ Adapter Wall/Pole Mount
1
DAntenna Support Plate
1
EHex Bolt M8x70
2
FHex Bolt M8x40
1
GHex Bolt M8x25
1
HFlat Washer M8
3
ISpring Washer M8
3
Description Qty
J Nut M8
1
K Safety Cable
1
L Waterproof RJ45 connector 2
M Optional Power Injector
1
Grounding Kit
Ring Terminal 1
Ground Screw
1
N
Lock Washer
2
Optional Mesh Antenna Kit
O Mesh Antenna
2
1. Assemble the ‘L’ Adapter
Assemble the ‘L’ Adaptor to the
GoBeam 5100 Unit.
Flat Washe
r
Hex Bol
t
“L” Adapte
r
S
p
rin
g
Washe
r

GoBeam 5100 Quick Installation Guide
UM000018 Rev 1.0
2. Assembling the Antennas
Attach the four 2.4 GHz band antennas to
terminals A1 to A4 and screw all antennas
into place by hand. Rotate each antenna at
its metallic base. The antennas should rotate
easily. Tighten the antenna by hand only.
Do not apply excessive force by using any
tool, as this may damage the unit.
Insert the four 2.4 GHz band antennas into the
Antenna Support Plate. The antennas must be
inserted evenly, so that the plate is level and
all the antennas are protruding the same
amount. The purpose of the support plate is to
stabilize the antennas and keeps them aligned
at all times. The plate is meant to fit tightly.
Use a bit of force if necessary.
3. Assembling the Optional Mesh Antennas
The Mesh Antennas are optional.
For the GoBeam 5100, assemble the
mesh antennas at the same time as
the other antennas.
4. Install the Mounting Brackets
When mounting the GoBeam 5100, the pole or wall mounting must
support a minimum of 61.6 lbs (28 kg). In addition, the pole or wall
mounting must support the wind loads from the GoBeam 5100. For
example, the wind load at a wind velocity of 100 mph (160 km/h) is
24.2 lbs (11 kg) and the wind load at a wind velocity of 165 mph
(264 km/h) is 66.1 lbs (30 kg).
Lorsque vous montez la GoBeam 5100, le poteau ou le montage
mural doit supporter d'un minimum de 61.6 lbs (28 kg). En outre,
le montage sur le poteau ou sur le mur doit appuyer les surcharges
dues au vent de la GoBeam 5100 (par exemple, 24.2 lbs (11 kg)
pour la vitesse du vent de 100 mph (160 km/h), 66.1 lbs (30 kg)
pour l'énergie éolienne Vitesse de 165 mph (264 km/h)).
Mesh
A
ntennas
2.4 GHz
Antennas

GoBeam 5100 Quick Installation Guide
UM000018 Rev 1.0
Narrow Pole (1”-1.75” diameter)
B
Pole
A
H
E
I
Normal Pole (1.75”-3” diameter)
Pole
A
E
B
H
I
Large Pole (larger than 3” diameter)
Stainless
Steel Hose
Clamp
A
Pole
Wall Mounting Bracket
Horizontal Pole Mounting Vertical Pole Mounting
5. Installing the Safety Cable
1. Wrap the safety cable around the
pole and insert the mounting plate
through the cable loop.
2. Attach the mounting plate to the
GoBeam 5100 unit using the
hexagonal bolts.
Flat Washe
r
Spring Washe
r
Nu
t
Spring Washe
r
Flat Washe
r
Safety
Cable
Bolts
Nu
t

GoBeam 5100 Quick Installation Guide
UM000018 Rev 1.0
6. Ground the GoBeam 5100 Unit
Connect the 10 AWG
grounding cable
before connecting any
other cables. When
removing the GoBeam
5100, the grounding
cable should be the
last cable removed.
Connecter la prise de terre 10 AWG avant de connecter tout autre
câble. Pendant la désinstallation du GoBeam 5100, la prise de terre
doit être le dernier câble retiré.
7. Connect the Ethernet PoE
Pin # Signal
1 Data
2 Data
3 Data
4 48V (+)
5 48V (+)
6 Data
7 48V (-)
8 48V (-)
8. Connect the 1Gbps Network Connection
When using 1Gbps Network
connection, use the Eth 1000
port as shown.
Pin # Signal Color
1 BI_DA+ white & green
2 BI_DA- green
3 BI_DB+ white & orange
4 BI_DC+ blue
5 BI_DC- white & blue
6 BI_DB- orange
7 BI_DD+ white & brown
8 BI_DD- brown
Eth 1000 Por
t
1G Network Cable