Goodman AVPTC 14 Series Manual
AVPTC**14** AIR HANDLERS
© 2018-2021, 2023
Daikin Comfort Technologies Manufacturing, L.P.
19001 Kermier Rd., Waller, TX 77484
www.goodmanmfg.com - or - www.amana-hac.com
P/N: IOA-4030H Date: April 2023
is a registered trademark of Maytag Corporation or its related companies and is used under license. All rights reserved.
Prior to installation, thoroughly familiarize yourself with this Installation
Manual. Observe all safety warnings. During installation or repair,
caution is to be observed. It is your responsibility to install the product
safely and to educate the customer on its safe use.
This device, which was assembled by Daikin Comfort
Technologies Manufacturing, L.P., contains a component
And this international radiator has an Industry Canada ID: IC
of this device is subject to two conditions:
(1) This device may not cause harmful interference; and
(2) This device must accept any interference received, including
interference that may cause undesirable operation.
And this device meets the applicable Industry Canada technical
calling 617-951-0200. (www.silabs.com)
Manufacturing, L.P., and may be contacted by calling (713)-
816-2500, or at 19001 Kermier Rd., Waller TX 77484. (www.
)
less the 20cm during normal operations.
Table of Contents
1 Important Safety Instructions 2
2 Shipping Inspection 3
3 Codes & Regulations 3
4 Replacement Parts 3
5 Pre-Installation Considerations 3
6 Installation Location 3
7 Refrigerant Lines 6
8 Condensate Drain Lines 9
9 Ductwork 10
10 Return Air Filters 10
Low Leakage Rate 10
12 Electric Heat 10
13 Electrical and Control Wiring 12
13
15 Cool Cloud HVAC Phone Application 14
14
15
16
19 Auxiliary Alarm Switch 17
20 Start-up Procedure 17
21 Accessories 17
18
19
24 Electric Air Cleaning 20
20
20
21
28 Air Handler Display 23
26
30 Wiring Diagram 27
30
2
1 Important Safety Instructions
The following symbols and labels are used throughout this
manual to indicate immediate or potential safety hazards. It is
with all safety information and instructions accompanying
the risk of personal injury, property damage, and/or product
damage.
CO can cause serious illness including permanent brain
damage or death.
Advertencia especial para la instalación de calentadores ó manejadoras
de aire en áreas cerradas como estacionamiento s ó cuartos de servicio.
El monóxido de carbono puede causar enfermedades severas
como daño cerebral permanente ó muerte.
Las emisiones de monóxido de carbono pueden circular a través
del aparato cuando se opera en cualquier modo.
RISQUE D'EMPOISONNEMENT AU MONOXYDE DE CARBONE
au CO pouvant survenir si un appareil produisant du monoxyde
2 Shipping Inspection
Always transport the unit upright; laying the unit on its side
or top during transit may cause equipment damage. The
installer should inspect the product upon receipt for shipping
damage and subsequent investigation is the responsibility
of the carrier. The installer must verify the model number,
3
correct prior to installation. The distributor or manufacturer
will not accept claims from dealers for transportation damage
or installation of incorrectly shipped units.
2.1 Parts
Also inspect the unit to verify all required components
are present and intact. Report any missing components
immediately to the manufacturer or to the distributor. Use
only factory authorized replacement parts (see Section
5). Make sure to include the full product model number
and serial number when reporting and/or obtaining
service parts.
2.2 Handling
Use caution when transporting/carrying the unit. Do
not move unit using shipping straps. Do not carry unit
with hooks or sharp objects. The preferred method of
carrying the unit after arrival at the job site is to carry
via a two-wheel hand truck from the back or sides or via
hand by carrying at the cabinet corners.
3 Codes & Regulations
This product is designed and manufactured to comply with
applicable national codes. Installation in accordance with
such codes and/or prevailing local codes/regulations is the
responsibility of the installer. The manufacturer assumes
no responsibility for equipment installed in violation of any
codes or regulations.
follow these regulations may harm the environment and
Should
www.epa.gov.
4 Replacement Parts
When reporting shortages or damages, or ordering repair
parts, give the complete product model and serial numbers
as stamped on the product. Replacement parts for this
product are available through your contractor or local
the white business pages, the yellow page section of the
local telephone book or contact:
HOMEOWNER SUPPORT
19001 KERMIER ROAD,
WALLER, TX 77484
855-770-5678
5 Pre-Installation Considerations
5.1 Preparation
Keep this document with the unit. Carefully read all
instructions for the installation prior to installing product.
Make sure each step or procedure is understood and
any special considerations are taken into account before
starting installation. Assemble all tools, hardware and
supplies needed to complete the installation. Some
items may need to be purchased locally. Make sure
everything needed to install the product is on hand
before starting.
5.2 System Matches
The entire system (combination of indoor and outdoor
sections) must be manufacturer approved and Air
Conditioning, Heating, and Refrigeration Institute
(AHRI) listed.
Installation of unmatched systems is not
permitted. Damage or repairs due to installation of
unmatched systems is not covered under the warranty.
5.3 Interconnecting Tubing
of refrigerant tubing when installing air handlers.
Refer to Remote Cooling/Heat Pump Service Manual
RS6200006, and TP-107 Long Line Set Application
R-410A for tubing guidelines. If possible, allow adequate
length of tubing such that the coil may be removed
(for inspection or cleaning services) from the cabinet
without disconnecting the tubing.
5.4 Clearances
The unit clearance from a combustible surface may be
0”. However, service clearance must take precedence.
A minimum of 24” in front of the unit for service clearance
is required. Additional clearance on one side or top will
be required for electrical wiring connections. Consult all
clearances. When installing this unit in an area that
may become wet (such as crawl spaces), elevate the
unit with a sturdy, non-porous material. In installations
that may lead to physical damage (i.e. a garage) it is
advised to install a protective barrier to prevent such
damage. Always install units such that a positive slope
in condensate line (1/4” per foot) is allowed.
5.5 Horizontal Applications
drain pan (as required by many building codes), must be
installed under the entire unit and its condensate drain
line must be routed to a location such that the user will
see the condensate discharge.
5.6 Access
This unit should be installed in a manner so that it is not
accessible to the public.
6 Installation Location
These air handlers are designed for indoor installa-
a min altitude of -184 feet below sea level.
If the unit is located in an unconditioned area with high
ambient temperature and/or high humidity, the air handler
may be subject to nuisance sweating of the casing. On these
barrier is recommended. A secondary drain pan below the
unit is also recommended to protect the installation site.
4
sections for more information).
6.1 Upow and Downow Installation (Figure 2 & 3)
1. Remove blower access panel and coil access panel.
The coil access panel and tubing panel may remain
screwed together during this procedure. Remove and
retain the seven (7) screws securing the coil access
blower access panel to the cabinet.
2. Slide the coil assembly out from the cabinet. Use the
drain pan to pull the assembly from the cabinet.
Do not use manifolds, copper lines, or
so may result in braze joint damage and leaks.
3. Removal of the center support is required on units
with 21” wide cabinet. Remove and retain the two (2)
screws that secure the center support to the cabinet.
Remove the center support.
a. Using the drain pan to hold the coil assembly, slide
the coil assembly back into the cabinet.
b. Reinstall the center support (if removed) using the
two (2) screws removed in Step 3.
c. Reinstall the coil access panels and reinstall blow-
er access panel removed in Step 1 as shown in
a.
b. Using the drain pan to hold the coil assembly, slide
the coil assembly back into the cabinet on the
c. Reinstall the center support (if removed) using the
two (2) screws removed in Step 3.
d. Reinstall the coil access panels and reinstall blow-
er access panel removed in Step 1 as shown in
Side Drain Pan and Extension Removal Instructions
drip shield support brackets to the condensate collectors
(front and back). Unsnap the side drain pan from the bottom
drain pan using a screwdriver or any small lever. The side
(A) is the primary drain for this application and condensate
drain line must be attached to this drain port. Drain port (a)
is for the secondary drain line (if used). When the side drain
pan is removed, the drain port opening in the access panel
must be covered by the accessory drain port plug (DPK1) as
Kit Number Application
DPK1 All Models
Side Drain Port Plug
Description
Drain Port Plug
Table 1
SIDE DRAIN PAN
DPK1 DRAIN PLUG
COIL ACCESS PANEL
MAIN DRAIN PAN
DRAIN PAN
Drip Pan
tension
Side
Drain
Pan
Screw
b
AMain Drain Pan
Drip Shield acket
Drip Shield
Pna
SIDE DRAIN PAN REMOVAL
5
6.2 Horizontal Left Installation (Figure 4)
for this application and condensate drain line must
be attached to this drain port. Drain port (b) is for the
secondary drain line (if used).
Remove red plugs from side drain pan before connecting
condensate drain pipes. Use removed plug to close drain
ports on vertical drain pan.
6.3 HORIZONTAL RIGHT INSTALLATION (Figure 5)
1.
panel and coil access panel. The coil access panel and
tubing panel may remain screwed together during this
procedure. Remove and retain the seven (7) screws
securing the coil access panel to the cabinet and the
cabinet.
2. Slide the coil assembly out from the cabinet. Use the
drain pan to pull the assembly from the cabinet.
braze joint damage and leaks.
3. Removal of the center support is required on units with
21” wide cabinet. Remove and retain the two (2) screws
that secure the center support to the cabinet. Remove
the center support.
4.
5.
6. Using the drain pan to hold the coil assembly, slide the
7. Reinstall the center support (if removed) using the two
(2) screws removed in Step 5.
8. Reinstall the coil access panels and reinstall blower ac-
9. Drain Connections for Horizontal Right Installation
a.
drain for this application and condensate drain line
must be attached to this drain port. Drain port (b) is
for the secondary drain line (if used).
b. Remove red plugs from side drain pan before con-
necting condensate drain pipes. Use removed plug
to close drain ports on vertical drain pan.
CMK000 8
Condensa te
Kit
CMK000 9
Condensa te
Kit
CMK001 0
Condensa te
Kit
CMK0012
Condensa te
Kit
CMK001 3
Condensa te
Kit
CMK001 4
Condensa te
Kit
AVPTC25B14 AVPTC29B14 AVPTC31C14 AVPTC49D14 AVPTC33C14 AVPTC49C14
AVPTC37B14 AVPTC37C14 AVPTC61D14 AVPTC39C14
AVPTC37D14
AVPTC59C14
AVPTC59D14
CONDENSATE KIT
Table 2
DFK-B DFK-C DFK-D
AVPTC25B14** AVPTC31C14** AVPTC37D14**
AVPTC29B14** AVPTC37C14** AVPTC49D14**
AVPTC35B14** AVPTC59C14** AVPTC59D14**
AVPTC37B14** AVPTC33C14** AVPTC61D14**
AVPTC39C14**
AVPTC49C14**
MODEL LIST FOR DOWNFLOW KITS
Table 3
If removing only the coil access panel from the unit,
must
so may result in panel damage.
Do not install the air handler in a location that violates the
instructions provided with the condenser. If the unit is located
in an unconditioned area with high ambient temperature and/
or high humidity, the air handler may be subject to nuisance
sweating of the casing. On these installations, a wrap of 2”
6
7 Refrigerant Lines
Refrigerant tubing must be routed to allow adequate
access for servicing and maintenance of the unit.
7.1 Tubing Size
the condenser/heat pump.
7.2 Tubing Preparation
All cut ends are to be round, burr free, and clean.
refrigerant leaks. The suction line is spun closed and
requires tubing cutters to remove the closed end.
To prevent possible damage to the tubing joints,
tubes. Always use clean gloves when handling coil
assemblies.
The use of a heat shield is strongly recommended
when brazing to avoid burning the serial plate or the
Heat trap or wet rags must be used
to protect heat sensitive components such as service
valves and TXV valves sensing bulb.
7
Ensure coil slides on the rails along the groove provided on the drain pan side
Upper Tie Plate
Control
Deck
Downflow
cket
Center
Support
lter
acket
lter
Access
Panel
Access
Panel
Coil
Access
Panel
Tubing
Panel
UV
Knockout
8
7.3 Tubing Connections for TXV Models
TXV models come with factory installed TXV with the
bulb pre-installed on the vapor tube.
1. Remove refrigerant tubing panel or coil (lower) access
panel.
2.
indicates possible leak.
3. Replace the refrigerant tubing panel.
4. Remove the spin closure on both the liquid and suction
tubes using a tubing cutter.
5.
grommet about 18” away from braze joint.
6.
slide insulation and grommet about 18” away from
braze joint.
7.
wet rag upon completion of brazing.
: The sensing bulb must be permanently located. A
heat shield, heat trap, or wet rag must be used during braz-
ing to prevent damage to the TXV valve.
8. Replace access panels, suction line grommet, insula-
tion and all screws.
RUER
OMMET
SUCTION LINE
WITH SPIN CLOSURE
7.4 Thermal Expansion Valve System Adjustment
The following information for the indoor unit should be
TXV if necessary.
1. Total static pressure is .5” WC or less.
2.
3.
Sheet for Indoor Unit.
4.
Service Manual RS6200006.
5.
6. Set the room thermostat to COOL, fan switch to AUTO
7. Set the temperature control well below room temperature.
Superheat adjustments should not be made until indoor
ambient conditions have stabilized. This could take up to
24 hours depending on indoor temperature and humidity.
minutes or until refrigerant pressures stabilize. Use the
following guidelines and methods to check unit operation
and ensure that the refrigerant charge is within limits. NOTE:
Charge two stage units on low stage.
1. Purge gauge lines. Connect service gauge manifold to
base-valve service ports.
2. Temporarily install a thermometer on the liquid line at
the liquid line service valve and 4-6” from the compres-
sor on the suction line. Ensure the thermometer makes
adequate contact and is insulated for best possible
readings. Use liquid line temperature to determine sub-
cooling and vapor temperature to determine superheat.
3. Check subcooling and superheat. The system should
-
then check subcooling.
a. If subcooling is low and superheat is high, add
stage compressor systems should have a Subcool-
b. If subcooling and superheat are high, adjust TXV
-
cooling.
1. Attach a pipe clamp thermometer near the suction line
service valve at the outdoor unit.
a. Ensure the thermometer makes adequate contact
for the best possible readings.
2. TXV-based systems should have a Superheat value of
3. Adjust Superheat by turning the TXV valve stem clock-
wise to increase and counterclockwise to decrease.
Adjustments should be made opening or closing the
valve by no more than ¼ turn at a time. Allow the sys-
tem to stabilize 15 to 20 minutes before making addi-
tional adjustments if necessary.
4. After adjustments are complete replace cap on adjust-
ment stem and tighten 1/6 turn.
5. Remove gauges and check the Schrader ports for
leaks and tighten valve cores if necessary. Install caps
9
In situations where the TXV must be removed and
replaced or re-installed into the system, the TXV should be
TXV. No more than 20 ft-lb torque should be applied to the
joints of the TXV.
R-410A
50 1
52 3
54 4
56 6
58 7
60 8
62 10
64 11
66 13
68 14
70 15
72 16
74 17
76 19
78 20
80 21
85 24
90 26
95 29
100 31
110 36
120 41
130 45
140 49
150 53
160 56
170 60
Table 4
R-410A
200 70
210 73
220 76
225 78
235 80
245 83
255 85
265 88
275 90
285 92
295 95
305 97
325 101
355 108
375 112
405 118
415 119
425 121
435 123
445 125
475 130
500 134
525 138
550 142
575 145
600 149
625 152
Table 5
8 Condensate Drain Lines
The coil drain pan has a primary and a secondary drain with
tightened to a torque of no more than 37 in-lbs. to prevent
damage to the drain pan connection. An insertion depth of
this torque.
1. Ensure drain pan hole is not obstructed.
2. -
ished space, it may be necessary to insulate the con-
densate drain line located inside the building. Use Ar-
®or similar material.
A secondary condensate drain connection has been
provided for areas where the building codes require it.
free drainage. Provide required support to the drain line to
prevent bowing. If the secondary drain line is required, run
the line separately from the primary drain and end it where
condensate discharge can be easily seen.
10
Water coming from secondary line means the coil
primary drain is plugged and needs immediate attention.
Insulate drain lines located inside the building or above
condensate trap to ensure proper drainage.
When units are installed above ceilings, or in other
-
drain pan under the coil cabinet enclosure.
The installation must include a “P” style trap that is located
as close as is practical to the evaporator coil. See Figure 11
for details of a typical condensate line “P” trap.
Units operating in high static pressure applications
Air Handler
2.75" MI
N.
POSITIVE LIQUID
SEAL REQUIRED
AT TRAP
Drain
Connection
2" MIN.
Trapped lines are required by many local codes. In
the absence of any prevailing local codes, please refer to
the requirements listed in the
Code.
A drain trap in a draw-through application prevents air from
being drawn back through the drain line during fan operation
thus preventing condensate from draining, and if connected
to a sewer line to prevent sewer gases from being drawn into
the airstream during blower operation.
Use of a condensate removal pump is permitted when
necessary. This condensate pump should have provisions
occur. A trap must be installed between the unit and the
condensate pump.
The evaporator coil is fabricated with
oils that may dissolve styrofoam and certain types of plas-
-
tain any of these materials.
Tip: Priming the “P” trap may avoid improper draining at the
initial installation and at the beginning of the cooling season.
9 Ductwork
This air handler is designed for a complete supply and return
ductwork system.
To ensure correct system performance, the ductwork is to
ACCA Manual D, Manual S and Manual RS for information
is to be used and sealed to the unit in a manner that will
prevent leakage.
an L-shaped sheet metal supply duct without any outlets or
registers located directly below the heater.
9.1 Return Ductwork
DO NOT LOCATE THE RETURN DUCTWORK IN
AN AREA THAT CAN INTRODUCE TOXIC, OR
DUCTWORK. The return ductwork is to be connected
10 Return Air Filters
When
(the cabinet size is the seventh letter of the model number).
Leakage Rate
Ensure all the gaskets remain intact on all surfaces as
shipped with the unit. These surfaces are areas between
the upper tie plate and coil access panel, blower access
and coil access panels, and between the coil access and
when tested in accordance with ASHRAE Standard 193.
12 Electric Heat
Refer to the installation manual provided with the electric
heat kit for the correct installation procedure. All electric heat
kits that are permitted to be used are the HKS series. Refer
with a given air handler. No other accessory heat kit besides
the HKS series may be installed in these air handlers.
11
The heating mode temperature rise is dependent upon the
(kW) selected. Use data provided in Tables 3, 4 and 5 to
3 5 6 8 1 0 1 5 19/2 0 2 5
8 0 0 1 2 1 9 2 3 3 1 3 7 5 6
1 0 0 0 9 1 5 1 9 2 5 3 0 4 4
1 2 0 0 8 1 2 1 5 2 1 2 5 3 7 4 9 6 2
1 4 0 0 7 1 1 1 3 1 8 2 1 3 2 4 2 5 3
1 6 0 0 6 9 1 2 1 5 1 9 2 8 3 7 4 6
1 8 0 0 5 8 1 0 1 4 1 6 2 5 3 3 4 1
2 0 0 0 5 7 9 1 2 1 5 2 2 3 0 3 7
C FM
H E A T K IT N O M IN A L k W
230/1/60 SUPPLY VOLTAGE - TEMP. RISE °F
Table 6
3568 1 0 1 5 1 9 /2 0 2 5
8 0 0 1 1 1 8 2 2 3 0 3 5 5 4
1 0 0 0 9 1 4 1 8 2 4 2 8 4 2
1 2 0 0 7 1 2 1 5 2 0 2 4 3 5 4 7 5 9
1 4 0 0 6 1 0 1 3 1 7 2 0 3 0 4 0 5 1
1 6 0 0 6 9 1 1 1 5 1 8 2 7 3 5 4 4
1 8 0 0 5 8 1 0 1 3 1 6 2 4 3 1 3 9
2 0 0 0 479 1 2 1 4 2 1 2 8 3 5
C FM
H E A T K IT N O M IN A L k W
220/1/60 SUPPLY VOLTAGE - TEMP. RISE °F
Table 7
3568 1 0 1 5 1 9 /2 0 2 5
8 0 0 1 0 1 7 2 1 2 8 3 3
1000 8 1 3 1 7 2 2 2 7 4 0
1200 7 1 1 1 4 1 9 2 2 3 3 4 5 5 6
1400 6 1 0 1 2 1 6 1 9 2 9 3 8 4 8
1600 5 8 1 0 1 4 1 7 2 5 3 3 4 2
1800579 1 2 1 5 2 2 3 0 3 7
2000478 1 1 1 3 2 0 2 7 3 3
CFM
HEAT KIT NOM INAL k W
208/1/60 SUPPLY VOLTAGE - TEMP. RISE °F
Table 8
3568 10 15 19 20 25
AVPTC25B14 550650700 800 850 875
AVPTC29B14 550650700 800 875 875
AVPTC35B14 550650700 800 875 1050
AVPTC37B14 550650700 800 875 1050
AVPTC31C14 600700770 880 970 1090 1280
AVPTC33C14 600700750 850 920 950
AVPTC37C14 700770 880 970 1090 1280
AVPTC39C14 700770 880 970 1090 1280
AVPTC49C14 800800 950 1090 1290 1345
AVPTC59C14 800800 950 1090 1290 1345
AVPTC37D14 870970 1060 1120 1220 1250
AVPTC49D14 950 1060 1150 1220 1520
AVPTC59D14 990 1110 1200 1240 1520 1520
AVPTC61D14 1030 1150 1250 1320 1650 1690 1750
HEATER (kW)
Model
MINIMUM CFM REQUIREMENTS FOR HEATER KITS
Table 9
formula is to be used:
Where: TR = Temperature Rise
kW = Heater Kit Actual kW
VC* = .96 (230 Supply Volts)
= .92 (220 Supply Volts)
= .87 (208 Supply Volts)
1.08 = Constant
VC* (Voltage Correction)
The Temperature Rise Tables can also be used to
heat and allow the system to reach steady state conditions.
Insert two thermometers, one in the return air and one in the
supply air. The temperature rise is the supply air tempera-
ture minus the return air temperature. Using the temperature
above. See Spec Sheets and/or Service Manual for more
information.
There are 6 options
available in the Comfort Setting Menu which impacts system
target run time and electric heat functionality. Electric heat
operation adjustments only apply if a communicating heat
pump is installed. Comfort Setting Options 1 – 5 have set
values for the System Target Runtime and option 6 enables
additional menus to customize all comfort settings. See list
below for the System Target Run times associated with the
help satisfy the thermostat slower or faster based on the
selection where option 1, with a 10 minute Target Runtime,
is attempting to satisfy much faster than option 5, with a 30
minute Target Runtime.
System Target Runtime:
Comfort Setting Option 1) 10 Minute System Target Runtime
Comfort Setting Option 2) 15 Minute System Target Runtime
Comfort Setting Option 3) 20 Minute System Target Runtime
Comfort Setting Option 4) 25 Minute System Target Runtime
Comfort Setting Option 5) 30 Minute System Target Runtime
This system will automatically
determine if the heat pump is capable of satisfying the
thermostat in the selected System Target Runtime. If the heat
pump is unable to satisfy in the selected time, electric heat
settings will determine how many attempts should be given
to the heat pump before temporarily locking it out and using
the furnace. These electric heat settings also determine at
what time the system should remove the temporary heat
pump lockout and run the heat pump again.
There are four adjustable items associated with back up
electric heat operation control. In the same way as the
System Target Time, each of these items have defaulted
values for Comfort Settings 1 – 5. Only when Comfort Setting
6 is selected will each item be available for full adjustment.
12
This is a
value that determines how far past the target runtime
the system should continue running the heat pump be-
this menu was set to 20% with a target runtime of 20
minutes. If the thermostat did not remove the heating
call after 20 minutes, the system would allow for an ad-
ditional 20% heat pump run (20% of the 20 minute tar-
get is an additional 4 minutes). In this case, the system
would turn on back up electric heat after 24 minutes
if the thermostat call was still present. Each time this
occurs, the system records this as a strike against the
heat pump (the strike is important when looking at the
Over Target Threshold)
If the
heat pump has consecutively activated back up electric
heat for the selected Over Target Threshold amount of
times, meaning for this many consecutive cycles it has
been unable to satisfy the target time by itself, then
the heat pump will be temporarily locked out and the
furnace will become the primary heat source.
This
only applies when the heat pump and back up electric
heat are activated on initial start-up. In this case, the
system will try to determine when the best time to op-
erate the heat pump individually again. To determine
this, the system looks at how easily the air handler is
able to satisfy the thermostat using the heat pump with
back up electric heat. Assume this setting is 15% and
the target time is 20 minutes. If the heat pump with
back up electric heat can satisfy the thermostat in less
than 17 minutes (20 minutes - 15% = 17 minutes) then
the algorithm records a strike against the air handler
(this strike is important when looking at the Under Tar-
get Threshold).
If
the air handler is able to satisfy the thermostat using
the heat pump with back up electric heat for the se-
lected number of consecutive cycles the electric heat
operation will be temporarily removed. The heat pump
can satisfy the thermostat in less than the System Tar-
get Runtime the back up heat operation will be com-
pletely removed and the heat pump will become the
primary heat source again. if it fails to do so, the strike
count against the furnace will be reset and the furnace
will remain the temporary primary heat source until the
Under Target Threshold is reached again.
The system will automatically make adjustments in an
attempt to satisfy the thermostat as close to this target
runtime as possible. After a power cycle or mode change
(cooling to heating or heating to cooling) the system will run
the initial cycle takes to satisfy the thermostat, the control
algorithm will adjust the system stage times for a 2 stage
unit or the capacity demand percentage for an inverter /
: Actual run times
may change depending on variations of load throughout the
day.
The following table shows the default values for all Comfort
Setting Options (1 – 5)
Comfort
Setti ng
Opti on
Target
Ti me
(Minutes)
Stage Up
Percentage
(%)
Stage Down
Percentage
(%)
Over Target
Threshhold
(Strike Count)
Under Target
Threshhold
(Strike Count)
110 20 20 210
215 20 20 4 8
320 20 20 6 6
425 20 20 8 4
530 20 20 10 2
The following table shows the ranges for each of item when
the adjustable Comfort Setting Option 6 is selected. The
the defaulted value. All items can be adjusted up or down
It is critical that these numbers be set properly. If
Comfort Setting option 3 is desired but a target time of 60 is
preferred, select Comfort Setting Option 6 to enable all the
adjustable menus, set the Target Time to 60 and make sure
the other menus are set to match that of Comfort Setting
Option 3.
Menu Minimum Value Maximum Value Default Value
Target Time (t9t) 1 minute 240 minutes 60 minutes
Stage Up Percent (SUP) 0% 100% 20%
Stage Down Percent (SdP) 0% 100% 20%
Over Target Threshold (Ott) 1 strike 254 strikes 20 strikes
Under Target Threshold (Utt) 1 strike 254 strikes 20 strikes
13 Electrical and Control Wiring
All routing of electrical wiring must be made
through provided electrical knockouts. Do not cut, puncture
or alter the cabinet for electrical wiring.
13.1 Building Electrical Service Inspection
This unit is designed for single-phase electrical supply
only. DO NOT OPERATE ON A THREE-PHASE
unit. The supply voltage must be measured and be in
agreement with the unit nameplate power requirements
and within the range shown.
Nominal Input Minimum Voltage Maximum Voltage
208-240197 253
ELECTRICAL VOLTAGE
Table 10
13.2 Wire Sizing
Wire size is important to the operation of your
equipment. Use the following check list when selecting
the appropriate wire size for your unit.
13
• -
• Refer to the NEC (USA) or CSA (Canada) for wire siz-
ing. The unit MCA for the air handler and the optional
electric heat kit can be found on the unit Series and
Rating Plate.
• -
•
varying ampacities - be sure to check the temperature
rating used.
Refer to the latest edition of the National Electric Code
or in Canada the Canadian Electric Code when deter-
mining the correct wire size.
13.3 Maximum Overcurrent Protection (MOP)
Every installation must include an NEC (USA) or CEC
(Canada) approved overcurrent protection device. Also,
check with local or state codes for any special regional
requirements.
Protection can be in the form of fusing or HACR style
circuit breakers. The Series and Rating Plate provides
13.4 Electrical Connections – Supply Voltage
Knockouts are provided on the air handler top panel
and sides of the cabinet to allow for the entry of the
knockouts on the cabinet sides are used for electrical
conduit, an adapter ring must be used in order to meet
UL1995 safety requirements. An NEC or CEC approved
strain relief is to be used at this entry point. Some codes/
municipalities require the supply wire to be enclosed in
conduit. Consult your local codes.
Side of
Cabinet
Top of
Cabinet
13.4.1 Air Handler Only (Non-Heat Kit Models)
The building supply connects to the stripped black
and red wires contained in the air handler electrical
compartment cavity. A ground screw is also contained
in this area. Attach the Supply wires to the air handler
conductors as shown in the unit wiring diagram using
appropriately sized solderless connectors or other NEC
or CEC approved means.
13.4.2 Air Handler - Non-Circuit Breaker Heat Kits
A terminal block is provided with the HKS kit to attach
the HKS Installation Manual and wiring diagram for
complete wiring details.
13.4.3 Air Handler With Circuit Breaker Heat Kit
The air handler has a plastic cover on the upper access
panel that will require either one or both sections to
be removed to allow the heat kit circuit breaker(s) to
be installed. The circuit breakers have lugs for power
supply connection. See the HKS Installation Instructions
for further details.
motor mount and rotate motor as shown in the AVPTC Motor
Orientation
female connections on the casing down. If the motor is not
oriented with the connections down, water could collect in
the motor and may cause premature failure.
14
MALE CONNECTIONS
SIDE VIEW
W
A
RNIN
SOW
A
REVER.
TOP
VIEW
AVPTC MOTOR ORIENTATION
15 Cool Cloud HVAC Phone Application
: This equipment has been tested and found to comply
reasonable protection against harmful interference in a resi-
dential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful in-
terference to radio communications. However, there is no
guarantee that interference will not occur in a particular in-
stallation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and
receiver.
—Connect the equipment into an outlet on a circuit
technician for help.
device being used.
Cool Cloud HVAC phone application designed to improve
error codes, observe system menu testing of all operational
modes (heat / cool / fan) directly from the phone. The phone
application is also capable of directly updating the air handler
software anytime updates are available. The application will
automatically notify the user.
The software update may take up to 20 minutes to
complete.
heating calls (including applications with backup electric
heater kits) the system only requires a single W input from
the thermostat. Internal algorithms will control all available
cooling and heating stages based on these inputs. Any sin-
-
ation, the thermostat must be setup to control a single stage
AC outdoor unit and to control single stage electric heat op-
eration. The control board does not accommodate an O wire
thermostat input (reversing valve signal). If a heat pump is
installed, the thermostat should be setup as stated above.
Setting the thermostat for the heat pump control or multi-
stage control may result in incorrect performance.
1. Connect all necessary thermostat wires to the thermo-
stat connector on the air handler control as instructed
by the applicable wiring diagrams shown in this section.
2. Connect the 1 & 2 wires between the indoor
and outdoor unit for communicating operation.
: Verify two stage outdoor units include a 24VAC
transformer (for outdoor control board power). Two
stage outdoor units may not behave properly without
this 24 VAC transformer.
15
OR HEAT PUMP
3. Download the Cool Cloud HVAC phone application for
Software and Air Handler Control Software are available, the
using the phone application. Ensure all mandatory software
updates and install if necessary.
16.1 Charging
1. Two-stage outdoor units using the Cool Cloud HVAC
application:
a. Using the cooling icon after entering the outdoor
unit menus, energize the outdoor unit at 49% ca-
pacity or lower.
b. Charge the outdoor unit as required using the
charging information provided with the outdoor
equipment.
with a Non-Communicating outdoor unit you must set
control the system only needs a single W input. Internal al-
gorithms will control staging automatically based on the sin-
instructions below:
1.
low voltage thermostat wires.
When installing the air handler with a non-com-
municating heat pump, wire directly to the “O” terminal
on the non-communicating heat pump. See the following
16
2. Download the Cool Cloud HVAC phone application.
-
cation Software and Air Handler Control Software are
-
-
datory and installed by using the phone application.
Ensure all mandatory software updates have been in-
stalled. Review notes for optional software updates and
install if necessary.
3. ) us-
ing the on board push buttons or the Cool Cloud HVAC
phone application. Select “” for single stage Air
Conditioners, “” for single stage Heat Pumps, “”
for two stage Air Conditioners and “” for 2 stage
Heat Pumps.
4. ) and select the ton-
the outdoor unit. See the following table.
stage operation.
Tonnage
Selecon Airow Tonnage
Selecon Airow Tonnage
Selecon Airow Tonnage
Selecon Airow
1 400 2.3 920 3.6 1440 4.9 1960
1.1 440 2.4 960 3.7 1480 5 2000
1.2 480 2.5 1000 3.8 1520 5.1 2040
1.3 520 2.6 1040 3.9 1560 5.2 2080
1.4 560 2.7 1080 4 1600 5.3 2120
1.5 600 2.8 1120 4.1 1640 5.4 2160
1.6 640 2.9 1160 4.2 1680 5.5 2200
1.7 680 3 1200 4.3 1720 5.6 2240
1.8 720 3.1 1240 4.4 1760 5.7 2280
1.9 760 3.2 1280 4.5 1800 5.8 2320
2 800 3.3 1320 4.6 1840 5.9 2360
2.1 840 3.4 1360 4.7 1880 6 2400
2.2 880 3.5 1440 4.8 1920
ModelM AX CFM
AVPTC25B14
AVPTC29B14
AVPTC35B14
AVPTC37B14
1200
AVPTC33C14 1300
AVPTC31C14
AVPTC37C14
AVPTC39C14
1600
AVPTC37D14
AVPTC49C14 1800
AVPTC49D14
AVPTC59C14 1900
AVPTC59D14
AVPTC61D14 2100
5. -
ure/test air handler operations.
The phone application cannot test a non- commu-
nicating outdoor unitThe thermostat will be required for
outdoor unit testing.
17.1 Electric Heater Kit Testing
1. Select the electric heat icon after entering the air handler
menus while using the Cool Cloud phone application.
2. Select any value less than 50% for low stage operation
and any value greater than 50% for high stage operation.
3.
properly for high stage operation.
operate at a reduced speed during a combined thermostat
thermostat or humidistat. This lower blower speed increases
the indoor coil. The control board is equipped with a 24
between the R and DH terminals. If the humidistat closes on
humidity rise or the thermostat energizes this terminal when
Logic Menu () to “” using the push buttons or Cool
Cloud HVAC phone application. If the humidistat opens on
humidity or the thermostat de-energizes this terminal when
to “” using the push buttons or Cool Cloud HVAC phone
application.
17
19 Auxiliary Alarm Switch
be used for a condensate switch install (designated by
connected AUX switch is normally closed and opens when
the water level in the evaporator coil base pan reaches an
undesirable level. The control responds by displaying a “ ”
AUX switch is detected to be in the closed position for 30
seconds, normal operation resumes and the error message
is no longer displayed.
The air handler includes three on-board push buttons
allowing users to navigate indoor and outdoor system
menus. The Right and Left buttons allow the user to scroll
through the main menus and to then scroll through available
to enter into a main menu and to then permanently select
options within those menus.
After scrolling to the desired option within a menu,
-
ing the Center button two times will select that option. The
you to the main menu.
18
Key Mitigations:
1. Full featured TS (dehum & overcool)
2. Connect G and dehum wire correctly
3. Dehumidistat
1) Install Dehum wire
and DO NOT install G
Wire
2) Install Dehumidistat
in living space or
return duct
Is there a setting in the
thermostat to enable
Dehum without fan? (G)
Yes
No
During a call for Dehum,
does the thermostat
provide 24V to Dehum, Y,
and G?
Yes No
Choose that setting
Wire the system and test
functionality
Yes No
Wire the system and
test functionality
Dehumidification Control Options
Dry Environment
Yes No
Install any 24VAC
thermostat on the
market - Use Y, W, G
signals
Thermostat has a Dehum or
Configurable terminal with
Dehum option
Yes
No
Does your thermostat have a
whole house Dehumidifier
setting?
Install Dehumidistat in
living space or return
duct
If the Dehumidistat
opens on a rise on
humidity, then you
will set Dehum logic
to Low via Coolcloud
app or push buttons
If the Dehumidistat
closes on a rise in
humidity, then you
will set Dehum logic
to High via Coolcloud
app or push buttons
Thermostat only sends Dehum + G on a
call for Dehum
A Dehumidistat needs to be installed in
the living space or return duct
If the Dehumidistat opens
on a rise on humidity,
then you will set Dehum
logic to Low via Coolcloud
app or push buttons
If the Dehumidistat closes on
a rise in humidity, then you will
set Dehum logic to High via
Coolcloud app or push buttons
19
function properly.
1. Make sure the installed 24VAC thermostat is capable of
controlling the accessory or accessories.
2. Connect the appropriate accessory control wires to the
accessory devices from the thermostat (see thermostat
manual for connection and setup instructions).
3. If the thermostat is capable of providing a continu-
-
4. -
ry using the indoor unit push button menus or the Cool
Cloud HVAC phone application.
5. Using the thermostat, independently test each acces-
sory in addition to the independently testing continuous
fan mode.
performance and increase comfort level. Select the desired
the push button menus.
•
1 min
•
stepping up to 50% of the full demand for 30 seconds.
-
1/2 min
1 min
•-
-
•
20
24 Electric Air Cleaner Warning
The control is equipped with an Accessory Relay and a
pair of ¼ inch accessory terminals which is normally open,
labeled EAC-IN and EAC-OUT (see accessory contacts
anytime the blower is running. A closed relay means the
two terminals will have continuity between them (the control
does not energize these contacts). It is recommended to
utilize 24VAC with these terminals and limit the current to
1A.
• Prior to start-up, ensure that all electrical connections
are properly sized and tightened.
•
application, neoprene gasket must be positioned at
section 13.
• Tubing must be leak free.
• Unit should be elevated, trapped and pitched to allow
for drainage.
• Low voltage wiring is connected.
•
to allow for drainage.
• Drain pan and drain tubing has been leak checked.
• Return and supply ducts are sealed.
• Unit is elevated when installed in a garage or where
• Unit is protected from vehicular or other physical
damage.
• Return air is not obtained from any areas where there
-
which may cause serious personal injury or death.
The only item to be maintained on a regular basis by the
perform all other services.
-
els. Do not use these diagrams for any other models. See
This product contains electronic components
connection of the ground. A dedicated ground from the main
power supply or an earth ground must be provided.
This manual suits for next models
4
Table of contents
Other Goodman Air Handler manuals
Goodman
Goodman ARUF Series Manual
Goodman
Goodman RS6100004 User manual
Goodman
Goodman AVPTC42D14 series Manual
Goodman
Goodman ACNF Series User manual
Goodman
Goodman AVPTC AVPTC183014 User manual
Goodman
Goodman ARPF User manual
Goodman
Goodman AVPTC Series Use and care manual
Goodman
Goodman AEPT User manual
Goodman
Goodman APD 14 M Series User manual
Goodman
Goodman CKF Series User manual
Goodman
Goodman AWUF18 User manual
Goodman
Goodman ADPF Manual
Goodman
Goodman ARUF Series User manual
Goodman
Goodman ARPT**14 Series Manual
Goodman
Goodman ASPF Series Manual
Goodman
Goodman AWST Series User manual
Goodman
Goodman AVPTC24B14A User manual
Goodman
Goodman RS6200006 User manual
Goodman
Goodman ACNF18 Series User manual
Goodman
Goodman AEPF User manual
Popular Air Handler manuals by other brands
Trane
Trane GAF2A0A36S3AEC Installer's guide
Lennox
Lennox ACBX32CM installation instructions
BLAUBERG Ventilatoren
BLAUBERG Ventilatoren KOMFORT Ultra D 105-A Operation manual
Salda
Salda RIRS 350 P EKO 3.0 Series MOUNTING AND INSTALLATION INSTRUCTION
Arfit
Arfit ECOEVO HE EC instruction manual
Swegon
Swegon ESENSA PX TOP 05 installation instructions
Ingersoll-Rand
Ingersoll-Rand TAMGB0A24V21DA Installer's guide
bora
bora USDF Assembly instructions
Trane Technologies
Trane Technologies Foundation BAYCCHT306 Series installation guide
Haier
Haier GE NAMP1 installation instructions
Nortek
Nortek B64VM Series installation instructions
AAON
AAON RM Series Installation instructions manual
VTS Medical Systems
VTS Medical Systems Ventus S Series Operation and maintenance manual
Trane
Trane TAMXB0A24V21DB Installation, operation and maintenance
TGM
TGM CAH-F18CGR1-FQA-E3 Technical manual
Trane
Trane IntelliPak with Symbio 800 Programming guide
RDZ
RDZ RNW 214 I Technical installation manual
Vents
Vents DVUT 300 HB user manual