Goodman ASXC160361A User manual

*SXC 16 SEER
Condensing Units
•RefertoServiceManualRS6200006forinstallation,operation,andtroubleshootinginformation.
•Allsafetyinformation must be followedasprovided in the ServiceManual.
•RefertotheappropriatePartsCatalogfor part number information.
•See models on page 3.
TECHNICAL MANUTECHNICAL MANU
TECHNICAL MANUTECHNICAL MANU
TECHNICAL MANUALAL
ALAL
AL
RT6114004r11
August2014
This manual is to be used by qualified, professionally trained HVAC technicians only. Goodman does
not assume any responsibility for property damage or personal injury due to improper service
procedures or services performed by an unqualified person.
Copyright © 2009-2014 Goodman Manufacturing Company, L.P.

PRODUCT IDENTIFICATION
2
The model number is used for positive identification of component parts used in manufacturing. Please use this number
whenrequestingserviceorpartsinformation.
WARNING
WARNING HIGH VOLTAGE!
Disconnect ALL power before servicing or installing this unit. Multiple power
sources may be present. Failure to do so may cause property damage, personal
injury or death.
ONLY individuals meeting (at a
minimum) the requirements of
an "entry level technician" as specified by the Air-Condi-
tioning, Heating, and Refrigeration Institute (AHRI) may
use this information. Attempting to install or repair this
unit without such background may result in product
damage, personal injury or death.
Goodman will not be responsible
for any injury or property damage
arising from improper service or service procedures. If
you install or perform service on this unit, you assume
responsibility for any personal injury or property damage
which may result. Many jurisdictions require a license to
install or service heating and air conditioning equipment.
WARNING
WARNING WARNING
WARNING
DSXC160241AA
PRODUCT TYPE:
C:CondenserR-22
H:Heat Pump R-22
X: Condenser R-410A
Z: Heat Pump R-410A
PRODUCT
FAMILY:
S: Split System
SEER:
SEER Rating
BRAND:
D: Deluxe
Goodman®
Brand
A: Amana®
Brand MAJOR
REVISION:
A:Initial Release
MINOR
REVISION:
A: Initial Release
ELECTRICAL:
1: 208-230V/1ph/60Hz
3: 208-230v/3ph/60Hz
4: 460v/3ph/60Hz
NOMINAL
CAPACITY:
024: 2 Tons
036: 3 Tons
048: 4 Tons
060: 5 Tons
COMMUNICATION
FEATURE:
C: 4-wire
Communication
Ready

PRODUCT IDENTIFICATION
3
The model number is used for positive identification of component parts used in manufacturing. Please use this number
whenrequestingserviceorpartsinformation.
* Indicates minor revision & is not used for order entry or inventory management
ASXC160241A*
ASXC160361A*
ASXC160481A*
ASXC160601A*
ASXC160241B*
ASXC160361B*
ASXC160481B*
ASXC160601B*
The United States Environmental Protection Agency (“EPA”) has issued various regulations re-
garding the introduction and disposal of refrigerants introduced into this unit. Failure to follow
these regulations may harm the environment and can lead to the imposition of substantial fines.
These regulations may vary by jurisdiction. Should questions arise, contact your local EPA office.
WARNING
WARNING
Do not connect or use any device
that is not design certified by
Goodman for use with this unit.
Serious property damage, personal injury, reduced unit
performance and/or hazardous conditions may result
from the use of such non-approved devices.
WARNING
WARNING To prevent the risk of property
damage, personal injury, or death,
do not store combustible materials or use gasoline or
other flammable liquids or vapors in the vicinity of this
appliance.
WARNING
WARNING
DSXC160241A*
DSXC160361A*
DSXC160481A*
DSXC160601A*
DSXC160481B*
DSXC160601B*

PRODUCT DESIGN
4
Modelscovered by this manualcomewithanew4-wirecom-
municatingPCB. When paired with a compatiblecommuni-
cating indoor unit and a communicating thermostat, these
modelscansupport4-wirecommunicationprotocolandpro-
videmoretroubleshootinginformation.Thesemodelsarealso
backwardcompatible with the legacythermostat wiring.
*SXC16 models are available in 2, 3, 4 and 5 ton sizes and
use R-410A refrigerant. They are designed for 208/230 volt
singlephaseapplications.
The condenser air is pulled through the condenser coil by a
direct drive propeller fan. This condenser air is then dis-
charged out of the top of the cabinet.
These units are designed for free air discharge, so no addi-
tional resistance like duct work shall be attached.
The suction and liquid line connections on present models
areofthe sweat type for field piping withrefrigeranttypecop-
per. Front seating valves are factory installed to accept the
fieldruncopper. The total refrigerantcharge for a normal in-
stallation is factory installed in the condensing unit. *SXC
units are charged for the matching evaporator coil and a 15
footrefrigerantlineset.
Systems should be properly sized by heat gain and loss
calculations made according to methods of the Air Condi-
tioning Contractors Association (ACCA) or equivalent. It is
the contractors responsibility to ensure the system has ad-
equate capacity to heat or cool the conditioned space.
*SXC16 models use the Copeland Scroll "Ultratech" Series
compressorswhichare specifically designed for R-410Are-
frigerant. Thereare anumberofdesign characteristics which
are different from the traditional reciprocating and/or scroll
compressors.
"Ultratech" Series scroll compressors with Copeland®
ComfortAlert diagnostics will not have a discharge thermo-
stat, some of the early model scroll compressors required
dischargethermostats.
Due to their design Scroll compressors are inherently more
tolerantofsmall quantities of liquid refrigerant.
NOTE: Eventhough the compressorsectionofaScroll com-
pressor is more tolerant of liquid refrigerant, continued
floodback or flooded start conditions may wash oil from the
bearingsurfacescausing premature bearing failure.
"Ultratech" Series scroll compressors use "POE" or
polyolesteroil whichis NOT compatiblewithmineraloilbased
lubricants like 3GS. "POE" oil must be used if additional oil
isrequired.
WARNING
To avoid possible injury, explosion or death, practice
safe handling of refrigerants.
Operating pressures and amp draws may differ from stan-
dardreciprocatingand/orscroll compressors. This informa-
tion may be found in the "Cooling Performance Data" sec-
tion.
This unit is for outdoor installation only. Refer to figure for
minimum clearances from the sides of the unit to full walls
andother objects.
NOTE: This unit cannot be completely enclosed. At least
one side must be unrestricted.
Theseclearanceswillhelpavoidairrecirculation.Ifinstalling
two or more units at the same location, allow at least 24
inches between units. If only one side is restricted (for ex-
ample, against the outside wall of a house), the unit may be
placed as close as 8" to that one wall.
DO NOT locate the unit:
* Directlyundera vent termination fora gas appliance.
* Within 3 feet of a clothes drier vent
* Wheretherefreezingofdefrostwaterwould create
ahazard
* Where water may rise into the unit.
OK!
OK!
AA AAA
A
CC
CCOK!
OK!
OK!
OK!
NOT
RECOMMENDED
AA
AA AA
AA
AA
B B B
B
Model Type A B C AA
Residential 10" 10" 18" 20"
Light Commercial 12' 12" 18" 24"

CONDENSING UNIT SPECIFICATIONS
5
NOTE: This data is provided as a guide, it is important to electrically connect the unit and properly size fuses/circuit breakers and
wires in accordance with all national and/or local electrical codes. Use copper wire only.
Unit specifications are subject to change without notice. ALWAYS refer to the unit's serial plate for the most up-to-date general
and electrical information.
Model Dimensions - W x Dx H
*SXC160241A* 29 x29 x32¼
*SXC160361A* 29 x29 x38¼
*SXC160481A* 35½ x35½ x38¼
*SXC160601A* 35½ x35½ x38¼
A/DSXC160241A* - A/DSXC160601A*
* Up to 24' in equivalent line length
(1) Wire size should be determined in accordance with National Electrical Codes; extensive wire runs will require larger wire sizes.
(2) Maximum Overcurrent Protection Device: MUST use Time Delay Fuse or HACR type Circuit Breaker of the same size as noted.
NOTES:
• Always check the S & R plate for electrical data on the unit being installed.
• Installer will need to supply 7/8" to 1-1/8" adapters for suction line connections (4 & 5 ton units).
• Installer will need to supply 3/4" to 7/8" adapters for suction line connections (3 ton unit).
• Unit is charged with refrigerant for 15' of 3/8" liquid line. System charge must be adjusted per Installation Instructions Final Charge
Procedure.
• Installation of these units requires the specified TXV Kit to be installed on the indoor coil. THE SPECIFIED TXV IS DETERMINED BY THE
OUTDOORUNIT,NOTTHEINDOORCOIL.
Dimensions
*SXC160241A* *SXC16036A* *SXC160481A* *SXC160601A*
Cooling Capacity, BTUH 24,000 36,000 48,000 60,000
Compressor
R.L. Amps 10.3 16.7 21.2 25.6
L.R. Amps 52.0 82.0 96.0 118.0
Low Pressure Switch
Open 22 PSIG 22 PSIG 22 PSIG 22 PSIG
Close 50 PSIG 50 PSIG 50 PSIG 50 PSIG
High Pressure Switch
Open 610 PSIG 610 PSIG 610 PSIG 610 PSIG
Close 420 PSIG 420 PSIG 420 PSIG 420 PSIG
Condenser Fan Motor
Horsepower 1/12 1/6 1/6 1/6
F.L. Amps 0.6 1.0 1.0 1.0
Liquid Line, Inches O.D.* 3/8" 3/8" 3/8" 3/8"
Suction Line, Inches O.D.* 3/4" 7/8" 1-1/8" 1-1/8"
Refrigerant Charge 137.0 157.0 202.0 197.0
Power Supply 208/230-60-1 208/230-60-1 208/230-60-1 208/230-60-1
Minimum Circuit Ampacity(1) 13.5 21.9 27.5 33.0
Maximum Overcurrent Device(2) 20 35 45 50
Electrical Conduit Size
Power Supply (Inches) 1/2 or 3/4 1/2 or 3/4 1/2 or 3/4 1/2 or 3/4
Approximate Shipping Weight 282 282 296 296
A/DSXC160[24-60]1A*

CONDENSING UNIT SPECIFICATIONS
6
NOTE: This data is provided as a guide, it is important to electrically connect the unit and properly size fuses/circuit
breakers and wires in accordance with all national and/or local electrical codes. Use copper wire only.
ASXC160[24-36]1B*
Dimensions
* Up to 24' in equivalent line length
(1) Wire size should be determined in accordance with National Electrical Codes; extensive wire runs will require larger wire sizes.
(2) Maximum Overcurrent Protection Device: MUST use Time Delay Fuse or HACR type Circuit Breaker of the same size as noted.
NOTES:
• Always check the S & R plate for electrical data on the unit being installed.
• Installer will need to supply 7/8" to 1-1/8" adapters for suction line connections (4 & 5 ton units).
• Installer will need to supply 3/4" to 7/8" adapters for suction line connections (3 ton unit).
• Unit is charged with refrigerant for 15' of 3/8" liquid line. System charge must be adjusted per Installation Instructions Final Charge
Procedure.
• Installation of these units requires the specified TXV Kit to be installed on the indoor coil. THE SPECIFIED TXV IS DETERMINED BY THE
OUTDOORUNIT,NOTTHEINDOORCOIL.
Model Dimensions - Wx D x H
ASXC160241B* 29 x 29 x 30¼
ASXC160361B* 29 x 29 x 30¼
ASXC160241BB ASXC160241BC ASXC160361BB ASXC160361BC
Cooling Capacity, BTUH 24,000 24,000 36,000 36,000
Compressor
R.L. Amps 10.3 11.7 16.7 15.3
L.R. Amps 52.0 58.3 82.0 83.0
Low Pressure Switch
Open 22 PSIG 22 PSIG 22 PSIG 22 PSIG
Close 50 PSIG 50 PSIG 50 PSIG 50 PSIG
High Pressure Switch
Open 610 PSIG 610 PSIG 610 PSIG 610 PSIG
Close 420 PSIG 420 PSIG 420 PSIG 420 PSIG
Condenser Fan Motor
Horsepower 1/6 1/6 1/6 1/6
F.L. Amps 1.1 1.1 0.9 0.9
Liquid Line, Inches O.D.* 3/8" 3/8" 3/8" 3/8"
Suction Line, Inches O.D.* 3/4" 3/4" 7/8" 7/8"
Refrigerant Charge 100.0 88.0 110.0 96.0
Power Supply 208/230-60-1 208/230-60-1 208/230-60-1 208/230-60-1
Minimum Circuit Ampacity(1) 14.0 15.7 21.8 20.0
Maximum Overcurrent Device(2) 20 20 35 35
Electrical Conduit Size
Power Supply (Inches) 1/2 or 3/4 1/2 or 3/4 1/2 or 3/4 1/2 or 3/4
Approximate Shipping Weight 198 198 202 202

CONDENSING UNIT SPECIFICATIONS
7
NOTE: This data is provided as a guide, it is important to electrically connect the unit and properly size fuses/circuit breakers and
wires in accordance with all national and/or local electrical codes. Use copper wire only.
Unit specifications are subject to change without notice. ALWAYS refer to the unit's serial plate for the most up-to-date general
and electrical information.
Model Dimensions - Wx D x H
ASXC160481B* 35½ x 35½ x 36¼
ASXC160601B* 35½ x 35½ x 38¼
* Upto24'inequivalentline length
(1) Wire size should be determined in accordance with National Electrical Codes; extensive wire runs will require larger wire sizes.
(2) Maximum Overcurrent Protection Device: MUST use Time Delay Fuse or HACR type Circuit Breaker of the same size as noted.
NOTES:
• Always check the S & R plate for electrical data on the unit being installed.
• Installer will need to supply 7/8" to 1-1/8" adapters for suction line connections (4 & 5 ton units).
• Installer will need to supply 3/4" to 7/8" adapters for suction line connections (3 ton unit).
• Unit is charged with refrigerant for 15' of 3/8" liquid line. System charge must be adjusted per Installation Instructions Final Charge
Procedure.
• Installation of these units requires the specified TXV Kit to be installed on the indoor coil. THE SPECIFIED TXV IS DETERMINED BY THE
OUTDOORUNIT,NOTTHEINDOORCOIL.
Dimensions
ASXC160[48-60]1B*
ASXC160481B* ASXC160481BC ASXC160601B* ASXC160601BC
Cooling Capacity, BTUH 48,000 48,000 60,000 60,000
Compressor
R.L. Amps 21.2 21.2 25.6 28.8
L.R. Amps 96.0 104.0 118.0 152.9
Low Pressure Switch
Open 55 PSIG 55 PSIG 22 PSIG 22 PSIG
Close 95 PSIG 95 PSIG 50 PSIG 50 PSIG
High Pressure Switch
Open 610 PSIG 610 PSIG 610 PSIG 610 PSIG
Close 420 PSIG 420 PSIG 420 PSIG 420 PSIG
Condenser Fan Motor
Horsepower 1/6 1/6 1/6 1/6
F.L. Amps 1.0 1.2 1.0 1.2
Liquid Line, Inches O.D.* 3/8" 3/8" 3/8" 3/8"
Suction Line, Inches O.D.* 1 1/8" 1 1/8" 1 1/8" 1 1/8"
Refrigerant Charge 135.0 135.0 200.0 200.0
Power Supply 208/230-60-1 208/230-60-1 208/230-60-1 208/230-60-1
Minimum Circuit Ampacity(1) 27.5 27.7 33.0 37.2
Maximum Overcurrent Device(2) 45 45 50 60
Electrical Conduit Size
Power Supply (Inches) 1/2 or 3/4 1/2 or 3/4 1/2 or 3/4 1/2 or 3/4
Approximate Shipping Weight 241 241 301 301

CONDENSING UNIT SPECIFICATIONS
8
NOTE: This data is provided as a guide, it is important to electrically connect the unit and properly size fuses/circuit
breakers and wires in accordance with all national and/or local electrical codes. Use copper wire only.
DSXC160241AB DSXC160241AC DSXC160361AB DSXC160361AC
Cooling Capacity, BTUH 24,000 24,000 36,000 36,000
Compressor
R.L. Amps 10.3 11.7 16.7 15.3
L.R. Amps 52.0 58.3 82.0 83.0
Low Pressure Switch
Open 22 PSIG 22 PSIG 22 PSIG 22 PSIG
Close 50 PSIG 50 PSIG 50 PSIG 50 PSIG
High Pressure Switch
Open 610 PSIG 610 PSIG 610 PSIG 610 PSIG
Close 420 PSIG 420 PSIG 420 PSIG 420 PSIG
Condenser Fan Motor
Horsepower 1/6 1/6 1/6 1/6
F.L. Amps 1.1 1.1 0.9 0.9
Liquid Line, Inches O.D.* 3/8" 3/8" 3/8" 3/8"
Suction Line, Inches O.D.* 3/4" 3/4" 7/8" 7/8"
Refrigerant Charge 100.0 88.0 110.0 96.0
Power Supply 208/230-60-1 208/230-60-1 208/230-60-1 208/230-60-1
Minimum Circuit Ampacity(1) 14.0 15.7 21.8 20.0
Maximum Overcurrent Device(2) 20 20 35 35
Electrical Conduit Size
Power Supply (Inches) 1/2 or 3/4 1/2 or 3/4 1/2 or 3/4 1/2 or 3/4
Approximate Shipping Weight 198 198 202 202
DSXC160[24-36]1A*
Dimensions Model Dimensions - W x D x H
DSXC160241A* 29 x 29 x 30¼
DSXC160361A* 29 x 29 x 30¼
* Up to 24' in equivalent line length
(1) Wire size should be determined in accordance with National Electrical Codes; extensive wire runs will require larger wire sizes.
(2) Maximum Overcurrent Protection Device: MUST use Time Delay Fuse or HACR type Circuit Breaker of the same size as noted.
NOTES:
• Always check the S & R plate for electrical data on the unit being installed.
• Installer will need to supply 7/8" to 1-1/8" adapters for suction line connections (4 & 5 ton units).
• Installer will need to supply 3/4" to 7/8" adapters for suction line connections (3 ton unit).
• Unit is charged with refrigerant for 15' of 3/8" liquid line. System charge must be adjusted per Installation Instructions Final Charge
Procedure.
• Installation of these units requires the specified TXV Kit to be installed on the indoor coil. THE SPECIFIED TXV IS DETERMINED BY THE
OUTDOORUNIT,NOTTHEINDOORCOIL.

CONDENSING UNIT SPECIFICATIONS
9
NOTE: This data is provided as a guide, it is important to electrically connect the unit and properly size fuses/circuit breakers and
wires in accordance with all national and/or local electrical codes. Use copper wire only.
Unit specifications are subject to change without notice. ALWAYS refer to the unit's serial plate for the most up-to-date general
and electrical information.
DSXC160[48-60]1B*
Dimensions Model Dimensions - W x D x H
DSXC160481B* 35½ x 35½ x 36¼
DSXC160601B* 35½ x 35½ x 38¼
* Upto24'inequivalentline length
(1) Wire size should be determined in accordance with National Electrical Codes; extensive wire runs will require larger wire sizes.
(2) Maximum Overcurrent Protection Device: MUST use Time Delay Fuse or HACR type Circuit Breaker of the same size as noted.
NOTES:
• Always check the S & R plate for electrical data on the unit being installed.
• Installer will need to supply 7/8" to 1-1/8" adapters for suction line connections (4 & 5 ton units).
• Installer will need to supply 3/4" to 7/8" adapters for suction line connections (3 ton unit).
• Unit is charged with refrigerant for 15' of 3/8" liquid line. System charge must be adjusted per Installation Instructions Final Charge
Procedure.
• Installation of these units requires the specified TXV Kit to be installed on the indoor coil. THE SPECIFIED TXV IS DETERMINED BY THE
OUTDOORUNIT,NOTTHEINDOORCOIL.
DSXC160481B* DSXC160481BC DSXC160601B* DSXC160601BC
Cooling Capacity, BTUH 48,000 48,000 60,000 60,000
Compressor
R.L. Amps 21.2 21.2 25.6 28.8
L.R. Amps 96.0 104.0 118.0 152.9
Low Pressure Switch
Open 55 PSIG 55 PSIG 22 PSIG 22 PSIG
Close 95 PSIG 95 PSIG 50 PSIG 50 PSIG
High Pressure Switch
Open 610 PSIG 610 PSIG 610 PSIG 610 PSIG
Close 420 PSIG 420 PSIG 420 PSIG 420 PSIG
Condenser Fan Motor
Horsepower 1/6 1/6 1/6 1/6
F.L. Amps 1.0 1.2 1.0 1.2
Liquid Line, Inches O.D.* 3/8" 3/8" 3/8" 3/8"
Suction Line, Inches O.D.* 1 1/8" 1 1/8" 1 1/8" 1 1/8"
Refrigerant Charge 135.0 135.0 200.0 200.0
Power Supply 208/230-60-1 208/230-60-1 208/230-60-1 208/230-60-1
Minimum Circuit Ampacity(1) 27.5 27.7 33.0 37.7
Maximum Overcurrent Device(2) 45 45 50 60
Electrical Conduit Size
Power Supply (Inches) 1/2 or 3/4 1/2 or 3/4 1/2 or 3/4 1/2 or 3/4
Approximate Shipping Weight 241 241 301 301

10
PERFORMANCE DATA ASXC160241A*-LOW STAGE
EXPANDED PERFORMANCE DATA COOLING OPERATION
MODEL: *SXC160241A* /CA*F3636C6** + TXV/ MBVC1200**-1**, Design Subcooling @AHRI 95°F Conditions,5°F @Serv. Vlv.
Outdoor Ambient Temperature
6
5
7
5
85 95 10
5
115
Entering Indoor Wet Bulb Temperature
IDB*
Ai
r
fl
o
w
5
9
63
6
77
1
5
9
63
6
77
1
5
9
63
6
77
1
5
9
63
6
77
1
5
9
63
6
77
1
5
9
63
6
77
1
MBh 16.1 16.7 18.3 - 15.8 16.3 17.9 - 15.4 15.9 17.5 - 15.0 15.6 17.0 - 14.3 14.8 16.2 - 13.2 13.7 15.0 -
S/T 0.69 0.58 0.40 - 0.71 0.60 0.41 - 0.73 0.61 0.42 - 0.76 0.63 0.44
-
0.78 0.65 0.45
-
0.79 0.66 0.46
-
Delta T 19 17 13 - 20 17 13 - 20 17 13 - 20 17 13
-
20 17 13
-
18 16 12
-
525 KW 1.08 1.10 1.14 - 1.17 1.19 1.23 - 1.24 1.27 1.31 - 1.31 1.34 1.39
-
1.37 1.40 1.45
-
1.42 1.45 1.50
-
A
MPS 4.4 4.5 4.6 - 4.7 4.8 5.0 - 5.1 5.3 5.4 - 5.5 5.6 5.8
-
5.8 6.0 6.2
-
6.2 6.3 6.5
-
HI PR 223 240 244 - 252 271 275 - 287 309 313 - 327 352 357
-
368 396 401
-
412 443 449
-
LO P
R
119 123 134 - 123 127 138 - 127 131 143 - 130 134 147
-
133 137 150
-
136 140 153
-
MBh 17.5 18.1 19.8 - 17.1 17.7 19.4 - 16.7 17.3 18.9 - 16.3 16.8 18.5 - 15.4 16.0 17.5 - 14.3 14.8 16.2 -
S/T 0.71 0.60 0.41 - 0.74 0.62 0.43 - 0.76 0.63 0.44 - 0.78 0.65 0.45
-
0.81 0.68 0.47
-
0.82 0.68 0.47
-
Delta T 19 17 13 - 19 17 13 - 19 17 13 - 20 17 13
-
19 17 13
-
18 16 12
-
70 600 KW 1.09 1.11 1.15 - 1.18 1.20 1.24 - 1.25 1.28 1.33 - 1.32 1.35 1.40
-
1.38 1.41 1.46
-
1.43 1.47 1.52
-
A
MPS 4.4 4.5 4.7 - 4.8 4.9 5.0 - 5.2 5.3 5.5 - 5.5 5.7 5.8
-
5.9 6.0 6.2
-
6.2 6.4 6.6
-
HI PR 226 243 246 - 255 274 278 - 290 312 316 - 330 355 360
-
372 400 405
-
416 447 454
-
LO P
R
120 124 136 - 124 128 140 - 128 132 144 - 132 136 148
-
134 138 151
-
137 142 155
-
MBh 18.0 18.7 20.4 - 17.6 18.2 20.0 - 17.2 17.8 19.5 - 16.7 17.4 19.0 - 15.9 16.5 18.1 - 14.7 15.3 16.7 -
S/T 0.75 0.63 0.43 - 0.78 0.65 0.45 - 0.80 0.66 0.46 - 0.82 0.69 0.48
-
0.85 0.71 0.49
-
0.86 0.72 0.50
-
Delta T 18 16 12 - 19 16 12 - 19 16 12 - 19 16 12
-
18 16 12
-
17 15 11
-
675 KW 1.10 1.12 1.16 - 1.19 1.21 1.25 - 1.26 1.29 1.34 - 1.33 1.37 1.41
-
1.39 1.43 1.48
-
1.44 1.48 1.53
-
A
MPS 4.5 4.6 4.7 - 4.8 4.9 5.1 - 5.2 5.3 5.5 - 5.6 5.7 5.9
-
5.9 6.1 6.3
-
6.3 6.4 6.6
-
HI PR 228 245 248 - 258 277 281 - 293 315 319 - 334 359 364
-
375 404 409
-
420 452 458
-
LO P
R
122 125 137 - 125 129 141 - 129 133 146 - 133 137 150
-
135 140 153
-
139 143 156
-
MBh 16.416.918.319.616.016.517.919.215.616.117.418.715.3 15.7 17.0 18.2 14.5 14.9 16.2 17.3 13.4 13.8 15.0 16.1
S/T 0.78 0.70 0.53 0.34 0.81 0.73 0.55 0.35 0.83 0.74 0.56 0.36 0.86 0.77 0.58 0.37 0.89 0.80 0.60 0.39 0.90 0.80 0.61 0.39
DeltaT22211712232117122321171223 21 17 12 23 21 17 12 21 19 16 11
525 KW 1.08 1.10 1.14 1.18 1.17 1.19 1.23 1.27 1.24 1.27 1.31 1.36 1.31 1.34 1.39 1.44 1.37 1.40 1.45 1.50 1.42 1.45 1.50 1.56
A
MPS 4.4 4.5 4.6 4.8 4.7 4.8 5.0 5.2 5.1 5.3 5.4 5.6 5.5 5.
6
5.8 6.0 5.8 6.0 6.2 6.4 6.2 6.3 6.5 6.8
HI PR 223 240 244 249 252 271 275 281 287 309 313 320 327 352 357 364 368 396 401 410 412 443 449 459
LO P
R
119 123 134 143 123 127 138 147 127 131 143 152 130 134 147 156 133 137 150 159 136 140 153 163
MBh 17.818.319.821.317.417.919.320.816.917.418.920.316.5 17.0 18.4 19.8 15.7 16.2 17.5 18.8 14.5 15.0 16.2 17.4
S/T 0.81 0.73 0.55 0.35 0.84 0.75 0.57 0.37 0.86 0.77 0.58 0.38 0.89 0.80 0.60 0.39 0.92 0.83 0.63 0.40 0.93 0.83 0.63 0.41
DeltaT22201712222117122221171223 21 17 12 22 20 17 12 21 19 16 11
75 600 KW 1.09 1.11 1.15 1.19 1.18 1.20 1.24 1.29 1.25 1.28 1.33 1.37 1.32 1.35 1.40 1.45 1.38 1.41 1.46 1.51 1.43 1.47 1.52 1.57
A
MPS 4.4 4.5 4.7 4.8 4.8 4.9 5.0 5.2 5.2 5.3 5.5 5.7 5.5 5.
7
5.8 6.1 5.9 6.0 6.2 6.4 6.2 6.4 6.6 6.8
HI PR 226 243 246 251 255 274 278 284 290 312 316 323 330 355 360 368 372 400 405 414 416 447 454 464
LO P
R
120 124 136 144 124 128 140 149 128 132 144 154 132 136 148 158 134 138 151 161 137 142 155 165
MBh 18.318.820.421.917.918.419.921.417.518.019.420.917.0 17.5 19.0 20.4 16.2 16.7 18.0 19.3 15.0 15.4 16.7 17.9
S/T 0.85 0.76 0.58 0.37 0.88 0.79 0.60 0.38 0.90 0.81 0.61 0.39 0.93 0.84 0.63 0.41 0.97 0.87 0.66 0.42 0.98 0.87 0.66 0.43
DeltaT21201611212016112220161122 2
0
16 11 21 20 16 11 20 18 15 10
675 KW 1.10 1.12 1.16 1.20 1.19 1.21 1.25 1.30 1.26 1.29 1.34 1.38 1.33 1.37 1.41 1.46 1.39 1.43 1.48 1.53 1.44 1.48 1.53 1.58
A
MPS 4.5 4.6 4.7 4.9 4.8 4.9 5.1 5.3 5.2 5.3 5.5 5.7 5.6 5.
7
5.9 6.1 5.9 6.1 6.3 6.5 6.3 6.4 6.6 6.9
HI PR 228 245 248 254 258 277 281 287 293 315 319 326 334 359 364 372 375 404 409 418 420 452 458 468
LO P
R
122 125 137 146 125 129 141 150 129 133 146 155 133 137 150 159 135 140 153 162 139 143 156 166
* EnteringIndoor DryBulbTemperature NOTE: Shadedarea is ACCA(TVA) conditions KW=Total system power Hi
g
h and low
p
ressures are measured atthe li
q
uid and suction service valves.
A
MPS=outdoor unit am
p
s
(
com
p
.+fan
)