Gorenje WA63080 User guide

gorenje
S E R V I C I N G I N S T R U C T I O N S
WASHING MACHINES 4-022-0414
TEHNIČNA PRIPRAVA
SERVISNIH STORITEV
Gorenje, d.d.
3503 Velenje, p.p.107, SLOVENIA
Telephone: [phone]
Telefax : [phone]
PG3 - FAILURES
FAILURE SHORT DESCRIPTION DESCRIPTION FAILURE DISPLAY
F1
connection to temperature
sensor open or short-
circuited
The failure is set, if the connection to the
temperature sensor is open or if there is a
short circuit between the two terminals of
the sensor. The washing program will be
ended without heating. The failure will be
displayed at the end of the washing
program.
On LCD:
ERROR 1
F2 The connection with door
lock is open
The failure is set, if the connection to the
door lock is open. The washing program
will stop. The failure will be displayed.
Supply of door lock will be ON. To start
the washing program, the user has to close
the door (program starts at once). To
continue the program (if failure happens
between washing program), the user has to
check if the door is closed and press the
„Start“-button. If the failure occurs again,
the washing program stops. Supply of door
lock will be OFF. If the water is in the
machine, than pumping 2 minutes. Failure
will be displayed again , and it is not
possible to start the washing program again.
On LCD:
ERROR 2
F3
the water level was not
reached.
- water tap closed
- leak in the machine
- valve defect
The failure is set, if within filling or heating
step the water level is below level 1 for the
filling time or 4 minutes in heating time. If
the failure occurs the first time within a
washing program, the current step starts
again. If the failure occurrs the second time
(twice in succession), the washing program
is stopped, and the failure will be displayed.
To continue the washing program, the user
has to press the „Start“-button. If the failure
occurs the third time, the washing program
stops, the failure will be displayed, and it is
not possible to start the washing program
again.
On LCD:
ERROR 3
F4
the connection to the tacho
generator is open or short-
circuited
If the washing program is active and the
motor control unit gets no signal from the
tacho generator, the first time the failure
occurs a pause of 1minute is executed. This
repeat 3 times. If once happen that motor
works O.K. than all previous failure must
be deleted. When the failure is detected the
4 time’s the washing program stops
immediately. If the temperature is higher
that 60°C than cool down with cold water
30 seconds. Then pumping water 2 minutes.
On LCD: ERROR 4

gorenje
S E R V I C I N G I N S T R U C T I O N S
WASHING MACHINES 4-022-0414
TEHNIČNA PRIPRAVA
SERVISNIH STORITEV VILI GARNBRET
Gorenje, d.d.
3503 Velenje, p.p.107, SLOVENIA
Telephone: [phone]
Telefax : [phone]
STOP the program. The failure will be
displayed.
F5 the triac is short-circuited
The failure is set, if the washing program is
active and the motor is working without
control of triac. The washing program is
stopped immediately. . After 2 minutes try
again. If the failure is not present, than
forget the first failure and continue work. If
is the same failure again, than program
stops complete. If the temperature is higher
that 60°C than cool down with cold water
30 seconds. Then pumping water 2 minutes.
STOP the program. The failure will be
displayed.
On LCD:
ERROR 5
F6
temperature not reached
- heater defect
The failure is set, if after a heating step the
temperature is more than 15°C lower than
the rated temperature. The washing
program will be ended normally. The
failure will be displayed at the end of the
washing program.
On LCD:
ERROR 6
F7
the water level does not fall
below level 1
- pump clogged
- pump defect
The failure is set, if after a pumping step
the water level did not fall below level 1. If
the failure occurs the first time within a
washing program, the current step will
started again. If the failure occurs the
second time (twice in succession), the
washing program is stopped and the failure
is displayed. To continue the washing
program, the user has to press the „Start“-
button. If the failure occurred the third
time, the washing program is stopped and
the failure is displayed. It is not possible to
start the washing program again.
On LCD:
ERROR 7
F8
The WM not reach max.
spin speed (the tapped field
relay does not switch)
The failure is set, if at the end of the
spinning cycle of the testing program the
spin is more than 100rpm lower than the
rated speed. The failure is displayed after
the end of the testing program.
On LCD:
ERROR 8
F9
Water inside machine
(Aqua Stop)
The failure is set, if Aqua Stop Sensor
makes signal (must be measuring min. 2
seconds). All valves switch OFF, the
heater switches OFF and main motor
STOPS. After 3 seconds check again. If the
failure is not present, than forget the first
failure and continue with program. If the
failure is still present, than switch ON the
pump for 2 minutes and stop WM. The
failure is displayed. It is not possible to
start the washing program again.
On LCD:
ERROR 9

gorenje
S E R V I C I N G I N S T R U C T I O N S
WASHING MACHINES 4-022-0414
TEHNIČNA PRIPRAVA
SERVISNIH STORITEV VILI GARNBRET
Gorenje, d.d.
3503 Velenje, p.p.107, SLOVENIA
Telephone: [phone]
Telefax : [phone]
NOTE:
According to the number of fault ton signal is on. This happens 10 times. After that there is no
ton signal but on LCD writes fault till not push button START or switch the machine OFF.
The most important fault is motor, than NTC, than water,…

gorenje
S E R V I C I N G I N S T R U C T I O N S
WASHING MACHINES 4-027-0706
TEHNIČNA PRIPRAVA
SERVISNIH STORITEV
Gorenje, d.d.
3503 Velenje, p.p.107, SLOVENIA
Telephone: [phone]
Telefax : [phone]
Test program for WM with timer PG3
MANUEL ACTION
ACTIVITY INDICATION
Press and hold buttons
START/PAUSE and
EASY IRONING and
turn round the program
knob for 1 step in left
(anti-clock side)
~10”
Self test of micro is executed and test program begins:
- all segments on LCD goes ON for 2 sec.
- after 2’’ on top line write SELF TEST , on bottom line
write max. spin speed for cotton and 99L and all symbols
are ON
- check if is Water clean sensor connect
(read voltage at empty drum)
All step can be 10”.
•If self test O.K, than on top line
write OK (for 2’’) and all other
segments and symbols switch OFF
•If self test is not O.K., than on top
line write ERROR all other
segments and symbols switch OFF,
WM stop
~12"
Door lock control (text on top line DOOR)
- PG3 activated door lock and wait, that contact is close
- max.10 sec)
•If it is O.K. than on top line write
DOOR OK (for 2’’)
•If it is not O.K. than on top line
write DOOR ERROR, WM stop
~4"
NTC control (text on top line NTC))
- check resistance of NTC (can be between 10 to 40°C)
Min. 2 sec
.
•If it is O.K. than on top line write
NTC OK (for 2’’)
•If it is not O.K. than on top line
write NTC ERROR, WM stop
~62"+20”
Water filling (text on top line WATER)
Open the valves Hot Water, Main Wash and Pre Wash.
Water goes in 3 different space in dispenser.
- HW : 5 ’’ (space 2), if it is connected to hot/cold water
- PW : 10’’ (space 1)
- MW : 10’’ (space 2)
- PW + MW : to reach level 1 (space 1,2 and 3)
- when reached level 1 than it is O.K.
- max. time for all is 60”
•If it is O.K. (before 60” reach level
1) than on top line write WATER
OK (for 2’’)
•If it is not O.K. than on top line
write WATER ERROR, WM stop
~12”
Water clean sensor (text on top line WATER SENSOR)
Only check if it is connected (check voltage at water in
drum together 10”)
•If it is connected than on top line
write WATER SENSOR YES (for
2’’)
•If it is not connected than on top
line write WATER SENSOR NO
~77"
Washing and heating (text on top line WASHING)
- Washing: 15’’ON / 5’’OFF / 15’’ON/5’’OFF
- 3 times repeats washing
- last wash is in spin direction and without pause
- Heater ON all time of washing
All together is 75’’. After this time switch OFF heater,
washing goes to spinning.
•If it is O.K. (after finish wash) –
washing in both direction, than on
top line write WASHING OK (for
2’’ – can be 2” in spinning)
•If it is not O.K. than on top line
write WASHING ERROR (for 2’’),
WM stop
~
40"
Spinning with water (text on top line SPIN)
- 40’’ spin from 50rpm to max.50 rpm
(or speed define with Pad’s, if is lower that 500 rpm)
- wait to drum stop
~42"
Draining (text on top line DRAIN)
- switch pump ON for 40 “
Check if water level fall under level 1
•If it is O.K. than on top line write
DRAIN OK (for 2’’)
•If it is not O.K. than on top line

gorenje
S E R V I C I N G I N S T R U C T I O N S
WASHING MACHINES 4-022-
0502
TEHNIČNA PRIPRAVA
SERVISNIH STORITEV VILI GARNBRET
Gorenje, d.d.
3503 Velenje, p.p.107, SLOVENIA
Telephone: [phone]
Telefax : [phone]
write DRAIN ERROR, WM stop
~62"
End spinning (text on top line SPIN SPEED)
- pump stay ON
- 10’’ spin from 0 rpm to max. rpm
(if necessary switch ON tape field)
- 50’’ on max. spin speed
- wait to drum stop
- switch OFF all component
•If it is O.K. than on top line write
SPIN SPEED OK (for 2’’)
•If it is not O.K. than on top line
write SPIN SPEED ERROR (for
2’’), WM stop
Turn the program knob
on 0 (OFF) position.
End the test program •On top line exchange (each 1 sec.)
END
WATER SENSOR YES (or NO)