Gorgy Timing LEDI NETWORK TDS V1 User manual

1
MDE-LEDI-NETWORK-TDS-4099V1.0
[email protected]
LEDI®NETWORK TDS V1
TIME SERVER
USER MANUAL
8
A
7
B
C
6532 4
D
E
87
F
632
1
A
B
C
D
E
1
F
- Unité : mm / Unit : mm 38, La MURE FRANCE
GORGY TIMING
2633
482
44
464,6
440
8,7 8,7
31,75
4x7,5
4x 10,5
H
Designation / Désignation
G
RACK LEDI NETWORK TS RATP 94000036
F
Drawing Nr / N° plan Drawn by / Dessiné par Date / Date
E
12000329 E.MAGNIEZ 25-Aug-17
D
Size / Format Check by / Vérifié par Scale / Echelle
C
A3 GORGY TIMING 2/5
B
A
25-Aug-17 EM PLAN D'ORIGINE
IND
DATE NAME MODIFICATION
Confidential drawing - Reproduction and transmission forbidden without Gorgy Timing s.a written authorization
Plan confidentiel - Reproduction et communication interdites sans autorisation écrite de la société Gorgy Timing
ECHELLE 3/10
ENGLISH

2MDE-LEDI-NETWORK-TDS-4099V1.0
WARNING! The following section provides the safety instructions for the installation. Please
read it carefully before installing your device.
To protect your device, connect power on UPS (Uninterruptible Power Supply).
The device must be connected to an electrical installation complying with the NF C15-100
standard.
The wiring installation must include an easily accessible power protection system (circuit-
breaker or disconnecting switch) compatible with the nominal voltage and current values
specied on the device.
In Europe: in accordance with European regulations on the protection of the people and the
environment, this device must be disposed of in a collection site designed for this purpose
(separately from household waste). Please contact your reseller, collection site or the com-
petent local authorities for more information.
Modifying or opening the product without the consent of the Customer service department
will void the warranty.
The LEDI®NETWORK TDS V1 must be installed, maintained and manipulated only by
a competent person.
All maintenance operation shall be conducted with power shut off, including on systems
connected to relay outputs if any.
Generally, the power cable (230V) and transmission cable (of time signal) should not be
too close to each other so as to avoid interferences (keep a distance of a few centimeters).
The LEDI®NETWORK TDS V1 must be located as far as possible from radiation sources
(speakers, antennas, high frequency equipment, electromagnetic alarms…) in order to avoid
electric interferences.
Gorgy Timing disclaims all liability in case of accident or damage caused by an improper use
of the LEDI®NETWORK TDS V1 .
All GORGY TIMING products comply with the following standards: CE, EN60950-1, EN55022
class B, EN50024
IMPORTANT SAFETY INSTRUCTIONS

3
MDE-LEDI-NETWORK-TDS-4099V1.0
General danger – ignoring the instructions may cause damage to the equipment.
Electrical Hazard – ignoring the instructions may result in electric shock and injury.
The equipment is completely protected through double insulation.
Warning
Please follow the precautions and instructions as indicated below in order to ensure your safety and
that of your environment, and to prevent any potential damage to your device.
Warning: a Switch-Isolator complying with the EN60947 standards is used as a disconnec-
ting device. It must be easily accessible and be installed close to the power cable. It must
disconnect all active polarities.
The LEDI®NETWORK TDS V1 is intended for indoors use only, at an altitude below 2000
meters.
Waste disposal by users in private households in countries of the European Union
This symbol on the product or the packaging indicates that the product must not be disposed
of into household waste. Instead, it is your responsibility to bring the waste to a collecting
station specically designed for recycling electric and electronic components. The separate
collection and recycling of your waste will contribute to the conservation of natural resources
and to ensure a safe, environmental and health friendly recycling. For more information
about the nearest recycling site, please contact the store where the device was purchased,
the waste disposal services or the competent local authorities.
Technical features
Power supply
Voltage 230Vac
Frequency 50-60Hz
Current 0,1 A Max
Dimensions
Length 482 mm
Width 266 mm
Height 44 mm
Operating conditions Maximum operating temperature 50°C
Humidity (non-condensed) 90 %
NOTICE OF SAFETY SIGNS ON THE PRODUCT
ENGLISH

4MDE-LEDI-NETWORK-TDS-4099V1.0
SUMMARY
1. INTRODUCTION............................................................................................................ 6
2. QUICKSTART ................................................................................................................ 7
3. SETTING UP THE SERVER, GENERAL INFORMATION ............................................ 8
3.1. MANUAL NETWORK CONFIGURATION ............................................................................ 8
3.2. OUTPUT CARDS CONFIGURATION .................................................................................. 8
3.3. ALARMS SETTINGS ........................................................................................................... 8
3.4. NTP PROTOCOL GENERAL INFORMATION ..................................................................... 9
3.5. GENERAL FACTS ABOUT SYNCHRONIZATION ............................................................. 10
3.6. OPERATING MODES OF THE LEDI®NETWORK TDS V1............................................... 10
4. FRONT LCD DISPLAY..................................................................................................11
4.1. STARTUP ............................................................................................................................11
4.2. TIME DISPLAY ................................................................................................................... 12
4.3. ALARM CONDITIONS........................................................................................................ 13
4.4. MANUAL IPV4 / IPV6 SETTINGS ...................................................................................... 14
4.4.1. Display current IP addresses.................................................................................. 14
4.4.2. Change the IP settings ........................................................................................... 14
4.4.3. IPv4 ........................................................................................................................ 15
4.4.4. IPv6 ........................................................................................................................ 17
4.5. RESTART UNIT.................................................................................................................. 19
5. WEB INTERFACE........................................................................................................ 20
5.1. Presentation ....................................................................................................................... 20
5.2. Web interface description ................................................................................................... 20
5.2.1. Navigation menu .................................................................................................... 20
5.2.2. "Index" page ........................................................................................................... 23
5.2.3. "Network" page....................................................................................................... 25
5.2.4. "Alarms" page......................................................................................................... 27
5.2.5. "SNMP" page.......................................................................................................... 29
5.2.6. "NTP" page............................................................................................................. 31
5.2.7. "Input" page ............................................................................................................ 36
5.2.8. "Output" page ......................................................................................................... 40
5.2.9. INTERFACE page .................................................................................................. 45
A. User Accounts ....................................................................................................... 45
B. Front LCD ............................................................................................................... 46
C. Other interfaces...................................................................................................... 46
D. Restart button......................................................................................................... 50
5.2.10. UPDATE page ...................................................................................................... 50
5.2.11. “Diagnostics” page ............................................................................................... 53

5
MDE-LEDI-NETWORK-TDS-4099V1.0
6. APPENDIX A – CONNECTIONS ................................................................................. 55
6.1. DCF-GPS ANTENNA ......................................................................................................... 56
6.1.1. DCF Antenna Réf : 3D6 (four meters cable included) ............................................ 56
6.1.2. Gps ANTENNA CONVERTER UNIT ..................................................................... 56
6.2. AFNOR-NFS-87500 / IRIG-B OUTPUT.............................................................................. 58
6.3. SERIAL IMPULSION OUTPUT .......................................................................................... 58
7. APPENDIX B – OUTPUT CODES FORMAT ............................................................. 59
8. APPENDIX C – MAINTENANCE ................................................................................. 61
8.1. CARD REPLACEMENT + IMPULSION CARD POWER.................................................... 61
8.2. MICROCONTROLERS REPLACEMENT .......................................................................... 62
8.3. OUTPUT CARDS ADDRESSES SWITCHES .................................................................... 63
8.4. TOP & IRIG B DCLS TIME CODE OUTPUT...................................................................... 64
8.5. SUPERVISION PROTOCOLS............................................................................................ 65
9. APPENDIX D – FIXES ................................................................................................. 66
ENGLISH

6MDE-LEDI-NETWORK-TDS-4099V1.0
1. INTRODUCTION
This document is the user manual for the LEDI®NETWORK TDS V1. This product is an
accurate and easily congurable time server.
It synchronizes through an NTP Ethernet 10/100 base T or DCF or GPS time input.
There are 3 available outputs: AFNOR NFS 87500 / IRIG B, IMPULSION, NTP.
The server communicates through the following network protocols:
►IPv4 et v6
►HTTP(S)
►SNMP
►Telnet
►SSH
►FTP
►SMTP
►Syslog
►(S)NTP
The security features ensure that the server only delivers reliable and continuous timing
information.
Dimensions
LEDI®NETWORK TDS V1 Rack
8
A
7
B
C
6532 4
D
E
87
F
632
1
A
B
C
D
E
1
F
- Unité : mm / Unit : mm 38, La MURE FRANCE
GORGY TIMING
2633
482
44
464,6
440
8,7 8,7
31,75
4x7,5
4x 10,5
HDesignation / Désignation
GRACK LEDI NETWORK TS RATP 94000036
FDrawing Nr / N° plan Drawn by / Dessiné par Date / Date
E12000329 E.MAGNIEZ 25-Aug-17
DSize / Format Check by / Vérifié par Scale / Echelle
CA3 GORGY TIMING 2/5
B
A25-Aug-17 EM PLAN D'ORIGINE
IND DATE NAME MODIFICATION Confidential drawing - Reproduction and transmission forbidden without Gorgy Timing s.a written authorization
Plan confidentiel - Reproduction et communication interdites sans autorisation écrite de la société Gorgy Timing
ECHELLE 3/10

7
MDE-LEDI-NETWORK-TDS-4099V1.0
2. QUICKSTART
CONTENT OF THE PACKAGE
Upon delivery, the box should contain the following elements:
►The 19" rack, bearing the mention ”LEDI®NETWORK TDS”
►A C13 power supply cable without locking
►An RJ45 Network cable
►A DVD-ROM that contains software and documentation
☛Please contact the customers service if one of the items above is
missing
CONNECTING THE SERVER
It may be useful to write down the serial number written on the identication stamp of the
1u 19” rack.
►Connect the synchronization outputs to the devices to be synchronized (see Appen-
dix A – Connections).
►Connect the LEDI®NETWORK TDS V1 server to the network using the network
cable.
NOTE: It is possible to connect the server directly to a computer using a
crossed network cable for settings/tests purposes.
►Connect the power supply cable to the server and switch ON to start it.
►The servers starts. The process may take up to one minute.
NOTE: initialization of the server is slower and may take up to three minutes
if there is no network cable connected.
►By default, the server is set up to get its IPv4 and IPv6 addresses from a DHCP
server. If such a server is present on the network, the LEDI®NETWORK TDS V1 is
can be accessed directly. Press any arrow key to display the IP Addresses on the
server’s LCD front screen.
►The GT Network Manager software (available on the DVD-ROM) can also detect
the server on the network and display the IP addresses.
ENGLISH

8MDE-LEDI-NETWORK-TDS-4099V1.0
3. SETTING UP THE SERVER,
GENERAL INFORMATION
3.1. MANUAL NETWORK CONFIGURATION
By default, the server obtains its IPv4 and IPv6 addresses from a DHCP server.
There are several ways to manually modify IPv4 and IPv6:
►By accessing the web interface, in the « Network » page. (See section 5.2.3. “Page
Network")
►By using the front buttons (See section 4.4.2. “IPv4" )
►By using the Telnet and SSH consoles (See section 5.2.9. “INTERFACE page")
Additionally, the server will automatically take an IP address in the 169.254.0.0/16 and
fe80::/10 pre-dened scopes. The IP addresses of the LEDI®NETWORK TDS V1 can be
displayed at any time by pressing any of the arrow keys on the front panel.
3.2. OUTPUT CARDS CONFIGURATION
The default conguration for all the output cards is to deliver UTC time and only when the
server is synchronized.
For most of the output boards, it is possible to modify the output time code format, time
zone and DST policy.
These settings can be modied in section 5.2.8. "Output Page".
3.3. ALARMS SETTINGS
►The LEDI®NETWORK TDS V1 has an embedded alarm system than can alert the
administrators in case of need.
►The LCD front screen displays the current alarms messages and its backlight blinks to
indicate that at least one alarm condition is happening.
►SNMP traps can be sent to one or several supervision stations.
►The server can send e-mails with details on the situation.
►The server can send Syslog frames to one or two servers.
►Le serveur peut envoyer des trames Syslog à un ou deux serveurs.
These three features can be congured in the « SNMP » and « Alarm » webpages (See
sections 5.2.4. “ALARMS Page" and 5.2.5. “SNMP page").

9
MDE-LEDI-NETWORK-TDS-4099V1.0
3.4. NTP PROTOCOL GENERAL INFORMATION
NTP (Network Time Protocol) is a network protocol designed to synchronize a device (the
client) with a time reference (the server). The LEDI®NETWORK TDS V1 is a server that
can synchronize numerous client devices from a main time source and optionally a client
capable of synchronizing on several servers.
In client/server mode, the client queries the server who answers with a time message. The
analysis of the transit times allows to determine the time difference between the client and
the server, thus deducing the appropriate correction.
NTP Exchange
In broadcast mode, the server periodically sends a time output on the network that is
received and used by NTP clients. This mode is bandwidth saving but less accurate5 than
the Client/ Server mode since the transit times are not compensated.
►The time distribution using the NTP protocol is always done in the UTC time format.
Time zones and DST must be set up on client sides.
►The NTP protocol can be used with MD5 hashes to authenticate the timing information.
The client and the server must use the same secret key and same key index (see sec-
tion "5.2.6. “NTP” page").
Query server date
Receive reply date
client side server side
Network
Return current server date
ENGLISH

10 MDE-LEDI-NETWORK-TDS-4099V1.0
3.5. GENERAL FACTS ABOUT SYNCHRONIZATION
The synchronization is the process during which, a local clock (internal) will be tuned by
aligning on a distant clock (the reference).
A local clock works with a reference frequency signal generated by an oscillator. The LEDI®
NETWORK TDS V1 uses a thermally compensated oscillator (TCXO).
►The offset is the instantaneous difference between two clocks.
►The drift is the late or advance that is taken by an oscillator as a consequence of its
imperfection. The better the oscillator, the lower the drift.
3.6. OPERATING MODES OF THE LEDI®NETWORK TDS V1
►Not synchronized: no available time input. The server does not have the correct time
and does not deliver time on its outputs.
►Autonomous: the server has been synchronized, but the input is no longer available. It
still has autonomy and keeps distributing time.
►Free Running: The server has been manually forced to run in autonomous mode (time
may have been set by the user). It delivers time on its outputs.
►Synchronized: The server is locked on a synchronization source. It delivers time on its
outputs.