Graco Husky 515 series User manual

INSTRUCTIONS-PARTS LIST
Husky 515
55-Gallon Dispenser Package
This manual contains important warnings
and information.
READ AND KEEP FOR REFERENCE.
INSTRUCTIONS
308666D
EN
100 psi (6.9 bar) Maximum Air Input Pressure
Models 231418, Series B and 26C115, Series A
Dispense Package with Gun
Models 231419, Series B and 26C116, Series A
Dispense Package
Table of Contents
Warnings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Parts Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Service and Technical Data . . . . . . . . . . . . . . . . 7
Dimensional Drawing . . . . . . . . . . . . . . . . . . . . . 7
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Graco Phone Number. . . . . . . . . . . . . . . . . . . . . 8
9294A
Model 231418 shown

2 308666D
Symbols
Warning Symbol Caution Symbol
WARNING
This symbol alerts you to the possibility of serious
injury or death if you do not follow the instructions.
CAUTION
This symbol alerts you to the possibility of damage to
or destruction of equipment if you do not follow the
instructions.
WARNING
INSTRUCTIONS
EQUIPMENT MISUSE HAZARD
Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury.
•This equipment is for professional use only.
•Read all instruction manuals, tags, and labels before operating the equipment.
•Use the equipment only for its intended purpose. If you are not sure, call your Graco distributor.
•Do not alter or modify this equipment.
•Check equipment daily. Repair or replace worn or damaged parts immediately.
•Do not exceed the maximum working pressure of the lowest rated component in your system. This
equipment has a 100 psi (7 bar) maximum working pressure.
•Use fluids and solvents that are compatible with the equipment wetted parts. Refer to the Techni-
cal Data section of all equipment manuals. Read the fluid and solvent manufacturer’s warnings.
•Always wear protective eyewear, gloves, clothing, and respirator as recommendedby the fluid and
solvent manufacturer.
•Comply with all applicable local, state, and national fire, electrical, and safety regulations.
•Route hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not
expose hoses to temperatures above 180F (82C) or below -40F (-40C).
•Do not lift pressurized equipment.

308666D 3
WARNING
FIRE AND EXPLOSION HAZARD
Improper grounding, poor ventilation, open flames, or sparks can cause a hazardous condition and
result in a fire or explosion and serious injury.
•Ground all equipment and the equipment being dispensed to. Refer to Grounding on page 6.
•If there is any static sparking or you feel an electric shock while using this equipment, stop dis-
pensing immediately. Do not use the equipment until you identify and correct the problem.
•Do not use kerosene or other flammable solvents or combustible gases to flush the unit.
•Provide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid
being dispensed.
•Keep the dispensing area free of debris, including solvent, rags, and gasoline.
•Do not smoke in the dispensing area.
•Extinguish all open flames and pilot lights in the dispensing area.
MOVING PARTS HAZARD
Moving parts, such as the rotating blades of the agitator, can pinch or amputate your fingers or other
body parts and can cause splashing in the eyes or on the skin.
•Keep clear of all moving parts when starting or operating the agitator.
•Always shut off the agitator and disconnect the air line before you remove the agitator from the
drum or check or repair any part of the agitator.
•Do not operate the agitator while an air line is hooked up to the elevator air fitting. Such operation
could cause the agitator blades to turn while the elevator is raised, which could result in serious
bodily injury or damage to the equipment from the hose getting tangled in the rotating agitator
blades.
TOXIC FLUID HAZARD
Hazardous fluids or toxic fumes can cause serious injury or death if splashed in the eyes or on the
skin, swallowed, or inhaled. When flushing the air motor or pump, keep your face away from the
exhaust port.

4 308666D
Parts Drawing
Husky 515 55-Gallon Dispense Package with Gun, Models 231418, Series B and 26C115,
Series A
Includes items 1 through 54
Husky 515 55-Gallon Dispense Package, Models 231419, Series B and 26C116, Series A
Includes items 1 through 27
9295A
25
54
7
6
8
9
10
12
11
13
14
15
16
17
19
18
20
21
22
23
24
24
50
51
53
1
2
3
3
4
52
18
5
1
2
3
3
4
5
27
restrictor
valve
agitator
needle
valve
elevator
air con-
trol valve
Husky 515 Diaphragm Pump
(see manual 308981)
Drum Cover Assembly
(see manual 308466)
Siphon Kit
(see manual 308609)
Elevator Assembly
(see 306287)
Heavy-Duty SST Drum Agitator
(see manual 308609)
1
2
3
4
5

308666D 5
Parts List
Husky 515 55-Gallon Dispense Package with Gun, Models 231418, Series B and 26C115,
Series A
Includes items 1 through 54
Husky 515 55-Gallon Dispense Package, Models 231419, Series B and 26C116, Series A
Includes items 1 through 27
Ref.
No. Part No. Description Qty.
1PUMP, Husky 515, acetal
See manual 308981. 1
241564 Models 231418, 231419
26C092 Models 26C115, 26C116
2238283 DRUM COVER ASSEMBLY
See manual 308466. 1
3238250 SIPHON KIT
See manual 308609. 1
4237746 ELEVATOR ASSEMBLY
See manual 306287. 1
5238157 DRUM AGITATOR, heavy
duty; SST See manual
308609.
1
6191565 BRACKET, pump 1
7191566 UNION, suction tube 1
8191567 NUT, union, swivel 1
9113575 O-RING, packing 1
10 111804 REGULATOR, air 1
11 111805 BLOCK, diverter 1
12 108190 GAUGE, air pressure 1
13 100086 WASHER, plain 4
14 100022 SCREW, cap 4
15 108094 NUT, lock 4
16 111821 SCREW, mach, hex head 1
17 111280 NUT, locking 1
18 156971 NIPPLE, short 2
19 110223 BALL VALVE, vented 1
20 108865 SCREW, mach, pan head 1
21 100721 PLUG, pipe, headless 1
22 169971 FITTING, air line 1
23 155541 UNION, swivel; 90? 1
24 203266 HOSE, coupled 2
25 208536 COUPLER, air line 1
27 110733 ELBOW, 45?, 1/4 npt 1
50 158212 BUSHING, pipe 1
51 238740 HOSE, coupled, conductive 1
52 237607 FLOW GUN, severe duty 1
53 168683 BUSHING, nozzle 1
54 161505 NOZZLE, flow gun 1
Ref.
No. Part No. Description Qty.

6 308666D
Installation
Mounting the Elevator Base to the Floor
1. Position the elevator where there is at least 9 feet
(2.75 meters) of overhead clearance.
2. Mark and drill holes in the floor for 0.5-in. (13 mm)
mounting bolts. See the mounting layout in the
Dimensional Drawing on page 7.
3. Level the elevator base, using shims if necessary,
and bolt the base firmly to the floor.
Grounding
Proper grounding is an essential part of maintaining a
safe system.
To reduce the risk of static sparking, the mounting cover
and all electrically conductive objects or devices in the
dispensing area must be properly grounded. Check your
local electrical code for detailed grounding instructions for
your area and type of equipment.
To ground the dispenser, connect the end of the
ground wire to a true earth ground.
Operation
Startup
See the Parts Drawing on page 4.
1. Flush the dispenser before first use.
NOTE: The pump was tested in water. To eliminate
possible contamination of the fluid you are pumping,
before you use the dispenser, flush the pump
thoroughly with a solvent compatible to the solvent
you are dispensing.
2. Ensure that the needle valve on the agitator is closed
and that the dispenser ball valve (19) is closed.
3. Connect the air supply line to the male air line
fitting (22).
4. Using the needle valve on the agitator to adjust the
agitator speed, gradually increase the speed until
you can see (through the inspection port in the drum
cover) movement in the surface of the liquid, but do
not increase the agitator speed enough to create a
vortex in the surface of the liquid. If the surface
begins to vortex, decrease the agitator speed to
prevent air entrainment.
NOTE: Always maintain moderate agitator speed,
which is approximately 50 rpm of the agitator blades.
Excessive agitator speed may cause vibration, foam-
ing of fluid, and increased wear on parts. Always agi-
tate fluid thoroughly before supplying it to the
dispensing equipment, and continue agitating fluid
while the dispensing equipment is being supplied.
5. Use the regulator (10) and ball valve (19) to control
the pressure and operation of the pump (1).
6. Raise or lower the elevator by pulling out or pushing
in the air control valve (a push-pull handle) on the rim
of the drum cover. Normal operation requires only a
few seconds for air pressure to build up and raise the
elevator or to exhaust and lower the elevator.
NOTE: To increase the operating speed of the
elevator, loosen the hex nut on the restrictor valve,
and turn the valve needle out. To decrease the
operating speed, turn the valve needle in. The
restrictor valve is on the top of the elevator, as shown
in the Parts Drawing.
WARNING
You must mount the elevator base to the floor before
you operate this equipment.
WARNING
MOVING PARTS HAZARD
To reduce the risk of serious injury,
including cuts, amputation of fingers by the
agitator blades, and splashing in the eyes
or on the skin, always shut off the agitator (disconnect
the air line from the agitator) before you raise, check,
or repair the agitator.
Never operate the agitator when the elevator is
raised. See MOVING PARTS HAZARD on page 3.

308666D 7
Service and Technical Data
See the individual component instruction manuals for service instructions and technical data.
Dimensional Drawing
NOTE: See individual component instruction manuals for dimensions of agitator,
pump, elevator, siphon kit, and drum cover.
9294A
ti22759a
height of unit from base
to top of pump when
elevator is raised
95 in.
(2413 mm)
57 in.
(1448 mm)
8.88 in.
(225.6 mm)
5.5 in.
(140 mm) 0.56-in.
(14.2 mm)
holes
25.9”
33.75”
35.62”
Elevator Base Mounting
Hole Layout

All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 308666.
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES P.O. BOX 1441 MINNEAPOLIS MN 55440-1441 USA
© COPYRIGHT 1996, GRACO INC. All Graco manufacturing locations are registered to ISO 9001.
www.graco.com
Revision D, October 2017
The Graco Warranty and Disclaimers
WARRANTY
Graco warrants all equipment manufactured by it and bearing its name to be free from defects in material and workmanship on the
date of sale by an authorized Graco distributor to the original purchaser for use. As purchaser’s sole remedy for breach of this
warranty, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment proven
defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for, any malfunction, damage or wear caused by faulty installation,
misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility with Graco
equipment of structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,
installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor
for verification of the claim. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any
defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts,
labor and transportation.
DISCLAIMERS AND LIMITATIONS
The terms of this warranty constitute purchaser’s sole and exclusive remedy and are in lieu of any other warranties (express or
implied), including warranty of merchantability or warranty of fitness for a particular purpose, and of any non-contractual
liabilities, including product liabilities, based on negligence or strict liability. Every form of liability for direct, special or
consequential damages or loss is expressly excluded and denied. In no case shall Graco’s liability exceed the amount of the
purchase price. Any action for breach of warranty must be brought within two (2) years of the date of sale.
EQUIPMENT NOT COVERED BY GRACO WARRANTY
Graco makes no warranty, and disclaims all implied warranties of merchantability and fitness for a particular purpose, with
respect to accessories, equipment, materials, or components sold but not manufactured by Graco. These items sold, but not
manufactured by Graco (such as electric motor, switches, hose, etc.) are subject to the warranty, if any, of their manufacturer.
Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.
Graco Phone Number
For the latest information about Graco products, visit www.graco.com.
For patent information, see www.graco. com/patents.
TO PLACE AN ORDER, contact your Graco distributor, or call to identify the distributor closest to you:
Phone: [phone] or Toll Free: 1-800-328-0211 Fax: [phone]