Granbo GN3613 User manual

Adjust Power Ultrasonic Cleaner
USER MANUAL
⊿Please read this instruction manual before using
⊿Keep this manual for reference
MODEL:GN3613

ACCESSORISE:
1.Main machine 2. Sound proof lid 3. Power lead 4.Mesh basket
APPLICATIONS:
Service line, Electron line, Medicament line, Laboratory, Machine line,
Horniness alloy line, Chemistry line, etc
PREPARATION:
1. Unpack the packing and check if any part get loose.
2. Keep the cleaner under ventilated and dry condition, place it flatly.
3. Make sure the plug connection is correct and firm. (Use triplex plug
and earth connection is required and safer.)
4. It’s optional to add certain amount of detergent when needed.
SPECIFICATIONS:
Model
GN3613
Power
2160W
Adjust power
0-2160W
Capacity
130L
Frequency
40KHz
Tank size
650*450*450mm (L×W×H)
Overall size
750*500*720 mm (L×W×H)
Set time
0-30minutes
Set temperature
0℃-80℃
Heating power
3000W
Power supply
AC220V 50Hz

OPERATION:
1. START UP ULTRASONIC FUNCTION:
1.Fill stainless steel tank with water
2.Plug the cleaner into grounded outlet;
3.Press the “ TIME+ ”key for setting 0-30 min working time. Press the
“TIME-” key for reduce the time continuous. Press “Ultrasonic” button
to “ON”, the cleaner will start working. During working, you will hear
the “ sizzling” voice ,that means the cleaner running properly. (Do not
run the cleaner continuously more than one hour at one time)
4.When the right knob will be Rotating around，you can adjust to the
power.
2. START UP HEATING FUNCTION:
1.Set temperature( if need) : Press the “ TEMP +” key for setting
temperature 0°C-80°C. Press the “TEMP - ”key for reduce
temperature.
2.Then press the “Heating” button to “ON” begin to heat.
3. STOP ULTRASONIC PROCESS:
1.Press the “Ultrasonic” button to “OFF”, the cleaner will stops
working, indicator light turn off. And then disconnect the power
supply.
2.Press the “Heating” button to “OFF”, the heating function will stop.
3.Empty the tank and clean both the outside and inside of the
cleaner with clean and dry cloth for next use.
Note:
⊿Always unplug and empty the cleaner after using.
⊿Remove the contaminants with moist cloth and water for the tank.
⊿Wipe the covering with dry towel.

Attentions:
a）While the machine is working normally, ultrasonic and tank syntony
gives a well-proportioned sound, and no shudder on the surface of the
water, yet there is spray made by the tiny bubbles. If there are
discontinuous surges, please add or release a little of washing solution in
the tank, stopping the surges is good for cleaning the objects.
b）On the condition of make sure the cleaning object is cleaned, please
run the machine discontinuously as far as possible(not more than
30min.),for long-time running causes temperature increment of the case,
and speedup the aging of the electronic devices.
c）Flammable cleaning solution is forbidden.
d）Do not start the heater nor ultrasonic while the tank is empty.
e）Prevent water or cleaning liquid from spattering into the case or
shaker.
f）When something is dropped into the tank carelessly, take it out
immediately.
g）Make sure the washing liquid is not hot, and turn the ultrasonic off and
pull out the plug, while changing or emptying the tank.
h）Clean the dirt in the tank after using.
i）Keep the surface of the machine clean.
Warning:
a）Don’t plug in the machine with empty tank – be sure to fill in proper
amount of liquid before plug-in the machine. Otherwise, the heater could
be damaged.
b）Never run the machine with low level of liquid to avoid damaging
ultrasonic transducers and heater.
c）Please note that when you run heater, the liquid in the tank could
vapor in the long time period, please keep watching the level of the liquid
in the tank
d）Washing liquid spatters into the shaker results in creepage and
short circuit, and burn the wafer as well.
e）Electrical abnormity will burn the transistor.
f）High voltage brings damages to the circuit and indicating lights etc.