Grandinroad Ultimate Animated Monster User manual

# 45479 Ultimate Animated Monster
Parts List:
Assembly Instructions:
Note: You will need a Phillips Head Screwdriver (not included)
A B C D E F G H
NO P Q R
Base Shoes x 2 Support Poles Chest Hoop
Hip hoop
S
Belt
Jacket Pants Head
Shoulder
support
Left arm
Right arm Torso frame
with attached motor
Collar
A/C Adapter
STEP 1 STEP 2 STEP 3
Hands x 2
J
I
K L
NOTE: The longer end of the (A) Base goes towards the
front.
First, slide (B) Shoes onto the (A) Base and then
assemble the (C) Support Poles through the tops of the
(B) Shoes as shown. Insert (N) Screws through the (C)
Support Poles and tighten to secure.
Lower (F) Pants over (C) Support Poles through the
pant leg openings & out through the top of the (F)
Pants. Assemble the (K) Waist Frame onto the (C)
Support Poles and insert (N) Screws and tighten to
secure. Attach the (P) Hip Hoop through the slot
housings on the sides of the (K) Waist Frame.
Easy to Follow Instructions
!
PROP 65 WARNING:
Handling the coated electrical wires of this product exposes you to lead, a chemical known to
the State of California to cause cancer, birth defects or other reproductive harm. Wash hands
after use.
Caution: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures; Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the
equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or experienced radio/TV technician for help.
This item, when assembled by the following instructions, should take 15 minutes to assemble. Please follow the step by step guide and
enjoy your Ultimate Animated Monster.
A/C Adapter Specification:
Input: 120V~ 60Hz
Output: 6VDC 800mA
Only use adapter with same
technical specification.
Please read all instructions carefully before assembling.
Care & Storage Instructions: Store product in its original package. Keep away from heat & moisture. For indoor use only. Save instruction sheet for future reference.
Loosen the Nut on the bottom of the (L) Torso Frame &
remove the Bolt. Set the (L) Torso Frame onto the (K)
Waist Frame as shown so that the center Bolt holes of
both parts are aligned. Insert the Bolt back through the
aligned Bolt holes of the (L) Torso Frame & (K) Waist
Frame and tighten with the Nut. Carefully connect the
connecting wire from the (L) Torso Frame to the
connecting wire from the Motor. Pull the (F) Pants over
the (P) Hip Hoop as shown and route the power cord
through and out the bottom of the right pant leg. Attach
the (D) Chest Hoop through the slot housings on the
sides of the (L) Torso Frame as shown.
Waist Frame Screws x 8 Cotter Pin x 4
M
12011 0602
N
C
B
A
P
D
F
KL

Assembly Instructions: (cont.)
STEP 4
Take the free end of the long cross bar attached to the right shoulder and attach to the raised
hooked support post on the (K) Waist Frame as shown, and secure with included (O) Cotter Pin.
Next, take the free end of the long cross bar attached under the left shoulder and attach to the
rotating shaft on the motor and secure with included (O) Cotter Pin.
Attach the (M) Shoulder Support as shown.
2
M
E
O
NOTE: Sensors are Light activated & work best in brighter environments. TIP: For best results, position a light to shine at the sensor so that people will have to pass between the light
source & the character – their shadow will activate the functions of the character.
STEP 6
STEP 5
Lower the (E) Jacket down over the (L) Torso Frame & (M) Shoulder Support, and
leave the back of the (E) Jacket open. Slide the (J) Right Arm up through the right
sleeve and slide the forked-hook into the right “shoulder” slot housing on the (L)
Torso Frame. Repeat for the (I) Left Arm. Set the (G) right & left Hands into place
by sliding the forked-hooks into the “wrist” slot housings on the ends of the arms.
Set the (H) Head onto the (L) Torso Frame by sliding the forked-hook into the “neck”
slot housing. Carefully connect the wires from the (H) Head to the connecting wires
from the (L) Torso Frame. Now secure hook & loop closures at the back of the (E)
Jacket. Wrap the (Q) Collar around his neck and the (R) Belt around his waist and
fasten the hook & loop closures on each to secure.
Attach the (S) A/C adapter to the power cord routed through the right pant leg &
plug into a standard power outlet to operate. When plugged into a standard power
outlet, the motion, lights & sounds are activated by a light-activated sensor.
G
G
I
J
S
H
Q
R
Sensor