Grandstream Networks UCM6100 Series User manual

Grandstream Networks, Inc.
www.grandstream.com
Grandstream Networks, Inc.
Configuring Permission/Privilege Level
Settings on UCM6100

Firmware Version 1.0.1.25 Configuring Permission/Privilege Level Settings on UCM6100 Page 1 of 7
Index
Table of Contents
CHANGE LOG ...........................................................................................2
Firmware Version 1.0.1.25.....................................................................................................................2
OVERVIEW ................................................................................................3
CONFIGURING EXTENSION PERMISSION..............................................4
CONFIGURING OUTBOUND ROUTE PRIVILEGE....................................5
CONFIGURING INBOUND ROUTE PRIVILEGE .......................................6
CONFIGURING IVR PERMISSION............................................................7
Table of Figures
Figure 1: Create an Extension on UCM6100................................................................................................4
Figure 2: Create an Outbound Route on UCM6100 .....................................................................................5
Figure 3: Create an Inbound Route on UCM6100........................................................................................6
Figure 4: Create an IVR on UCM6100 - Default Setting...............................................................................7
Figure 5: Create an IVR on UCM6100 - Dial Trunk Enabled........................................................................7
This document is subject to change without notice. The latest electronic version of this document is
available for download here:
http://www.grandstream.com/support
Reproduction or transmittal of the entire or any part, in any form or by any means, electronic or print, for
any purpose without the express written permission of Grandstream Networks, Inc. is not permitted.

Firmware Version 1.0.1.25 Configuring Permission/Privilege Level Settings on UCM6100 Page 2 of 7
CHANGE LOG
This section documents significant changes from previous versions of this configuration guide. Only major
new features or major document updates are listed here. Minor updates for corrections or editing are not
documented here.
Firmware Version 1.0.1.25
This is the initial version.

Firmware Version 1.0.1.25 Configuring Permission/Privilege Level Settings on UCM6100 Page 3 of 7
OVERVIEW
This document introduces the permission and privilege settings on the UCM6100 series IP PBX. The
permission and privilege settings are used to control the calls on extension, IVR, inbound route and
outbound route so that the UCM6100 can securely handle the calls as desired.
There are four levels of permission/privilege settings on the UCM6100. They are:
Internal: The lowest level. This is the default level.
Local
National
International: The highest level.
Those options apply to extension setting (Permission), IVR setting (Permission), inbound route setting
(Privilege Level) and outbound route setting (Privilege Level).

Firmware Version 1.0.1.25 Configuring Permission/Privilege Level Settings on UCM6100 Page 4 of 7
CONFIGURING EXTENSION PERMISSION
On the UCM6100 web GUI, create an extension under PBX->Basic/Call Routes->Extensions. Users
shall see "Permission" option with four levels in the drop down list.
Figure 1: Create an Extension on UCM6100
This "Permission" option restricts whether this extension could be used to make desired outgoing calls.
The extension needs to be assigned with higher level (or equal level) permission compared to the
outbound rule's privilege in order to make outbound calls with that rule.

Firmware Version 1.0.1.25 Configuring Permission/Privilege Level Settings on UCM6100 Page 5 of 7
CONFIGURING OUTBOUND ROUTE PRIVILEGE
When creating a new outbound rule under PBX->Basic/Call Routes->Outbound Routes, users shall see
"Privilege Level" option with four levels in the drop down list.
Figure 2: Create an Outbound Route on UCM6100
When making an outbound call via this route from an UCM6100 extension, the UCM6100 will compare the
extension's permission level with the outbound route's privilege level. If the extension's permission level is
higher than (or equal to) the outbound route's privilege level, the call will be allowed to go through.
Please see more descriptions below:
Internal: The lowest level required. All users can use this rule.
Local: Users with Local, National, or International level are allowed to use this rule.
National: Users with National or International level are allowed to use this rule.
International: The highest level required. Only users with international level can use this rule.

Firmware Version 1.0.1.25 Configuring Permission/Privilege Level Settings on UCM6100 Page 6 of 7
CONFIGURING INBOUND ROUTE PRIVILEGE
When creating a new inbound rule under PBX->Basic/Call Routes->Inbound Routes, users shall see
"Privilege Level" option with four levels in the drop down list.
Figure 3: Create an Inbound Route on UCM6100
This "Privilege Level" option applies to the inbound rule only when "Default Destination" is set to "by DID".
(IVR is handled in a different way; the other options in the "Default Destination" can be considered as
internal extension on the UCM6100)
When there is an inbound call from the trunk to the UCM6100 via this inbound route, the UCM6100 will
compare the inbound route's privilege level with the matching outbound route's privilege level (i.e, the DID
pattern in this inbound route matches one of the outbound route). If the inbound route's privilege level is
higher than (or equal to) the matching outbound route's privilege level, the call will be allowed to go
through.

Firmware Version 1.0.1.25 Configuring Permission/Privilege Level Settings on UCM6100 Page 7 of 7
CONFIGURING IVR PERMISSION
When creating an IVR under PBX->Call Features->IVR, users shall see "Dial Trunk" and "Permission"
options. By default, the "Dial Trunk" option is disabled. Also, the "Permission" level is set to "Internal"
(lowest level) and not configurable.
Figure 4: Create an IVR on UCM6100 - Default Setting
If "Dial Trunk" is enabled, users could specify the IVR permission level. Therefore, the calls coming into
IVR can dial outbound via trunk. In this case, the UCM6100 will compare the IVR's permission level with
the outbound route's privilege level. If the IVR's permission level is higher than (or equal to) the outbound
route's privilege level, the call will be allowed to go through.
Figure 5: Create an IVR on UCM6100 - Dial Trunk Enabled
* Asterisk is a Registered Trademark of Digium, Inc.