Grandstream Networks GWN7600LR User manual

For Warranty and RMA information, please visit www.grandstream.com
Grandstream Networks, Inc.
126 Brookline Ave, 3rd Floor
Boston, MA 02215. USA
Tel : [phone] - 9300
Fax: [phone] - 1987
www.grandstream.com
GWN7600LR
Outdoor Long-range 802.11ac Wave-2
WiFi Access Point
Quick Installation Guide

Content
English......................................................... 1
简体中文..................................................... 7

~1~ ~2~
OVERVIEW
This WiFi long range access point is designed to provide extended coverage support. Ideal
for outdoor WiFi solutions thanks to its waterproof casing and heat resistant technology.
The GWN7600LR comes equipped with dual-band 2x2:2 MU-MIMO with beam-forming
technology and a sophisticated antenna design for maximum network throughput and
extended WiFi coverage range of up to 275 meters. To ensure easy installation and
management, the GWN7600LR uses a controller-less distributed network management design
and an embeded controller within the product’s web user interface. This allows each access
point to manage a network of up to 30 GWN76xx series APs independently without
needing separate controller hardware/software and without a single point-of-failure. Its easy
installation and management features packed with extra coverage support and advanced
performance features make the GWN7600LR an ideal enterprise AP for mid-size wireless
network deployments.
1 x GWN7600LR Access Point
1 x Quick Installation Guide
1 x GPL Statement
4 x Screw (PM8 x 115)
4 x Locknut
4 x Screws and Anchors
EN
1 x Base Bracket
PACKAGE CONTENTS
2 x Assembled Screw
1 x Cover Bracket
1 x Hex Key
GWN7600LR PORTS
Port Description
NET/POE Ethernet RJ45 port (10/100/1000Mbps) supporting PoE.
NET Ethernet RJ45 port (10/100/1000Mbps) to your router or another
GWN76xx.
RESET Factory reset button. Press for 7 seconds to reset factory default
settings.
POWERING AND CONNECTING THE GWN7600LR
Network Port RJ45 Ethernet Cable to
power over Ethernet (PoE)
Switch
●Do not attempt to open, disassemble, or modify the device.
●Do not expose this device to temperatures outside range of -30 °C to 60 °C for operation.
●Do not expose this device to temperatures outside range of -30 °C to 60 °C for storage.
●Do not expose the GWN7600LR to environments outside of the following humidity range:
10-90% RH (non-condensing).
● Do not power cycle your GWN7600LR during system boot up or rmware upgrade. You
may corrupt rmware images and cause the unit to malfunction.
PRECAUTIONS
GWN7600LR can be powered on via PoE switch using following steps:
Step 1:
Plug a RJ45 Ethernet cable into the network port of the GWN7600LR.
Step 2:
Plug the other end into the uplink port of the power over Ethernet (PoE) switch.

~3~ ~4~
Horizontal Mounting
HARDWARE INSTALLATION
GWN7600LR can be mounted horizontally or vertically on a metal bar.
Please refer to the following steps for the appropriate installation.
Vertical Mounting
4. Connect the Ethernet cable (RJ45) to the correct ports of your GWN7600LR.
5. Align the GWN7600LR with the Base Bracket and pull it down to the right position.
6. Install the 2x Assembled screws to x GWN7600LR on the Mounting Bolt.
1. Prepare the Cover Bracket by inserting the 4 screws (PM8) into corresponding holes.
2. Attach the Cover Bracket with screws on the vertical Mounting Bolt where GWN7600LR
will be installed.
3. Assemble the Base Bracket with the Cover Bracket using provided locknuts and screws
(PM8).
1. Prepare the Cover Bracket by inserting the 4 screws (PM8) into corresponding holes.
2. Attach the Cover Bracket with screws on the horizontal Mounting Bolt where GWN7600LR
will be installed.
3. Assemble the Base Bracket with the Cover Bracket using provided locknuts and screws
(PM8).
4. Connect the Ethernet cable (RJ45) to the correct ports of your GWN7600LR.
5. Align the GWN7600LR with the Base Bracket and pull it down to the right position.
6. Install the 2x Assembled screws to x GWN7600LR on the Mounting Bolt.
123
45
12
3
45

~5~ ~6~
CONNECT TO GWN7600LR DEFAULT WIFI NETWORK
GWN7600LR can be used as standalone access point out of box, or after factory reset with
Wi-Fi enabled by default.
After powering the GWN7600LR and connecting it to the network, GWN7600LR will broad-
cast a default SSID based on its MAC address GWN[MAC’s last 6 digits] and a random
password.
Note: GWN7600LR’s default SSID and password information are printed on the MAC tag
of the unit.
This device has not been authorized as required by
the rules of the Federal Communications Commission.
This device is not, and may not be,
offered for sale or lease, or sold or leased,
until authorization is obtained.
GWN7600LR
SSID:GWNXXXXXX
S/N XXXXXXXXXXXXXXXX
MAC XXXXXXXXXXXX
WiFi Password: XXXXXXXX
( ) P/NNN XXX-XXXXX-XXXXX
48V 0.5A GigE POE
Method 2: Discover GWN7600LR using GWN Discovery Tool
1. Download and install GWN Discovery Tool from the following link:
http://www.grandstream.com/tools/GWNDiscoveryTool.zip
2. Open the GWN DiscoveryTool, and click on Scan.
3. The tool will discover all GWN76XX Access Points connected on the network showing
their MAC and IP addresses.
4. Click on Manage Device to be redirected directly to the GWN7600LR’s conguration
interface, or type in manually the displayed IP address on your browser.
Notes :
●Make sure that the GWN7600LR is not already controlled by another GWN Series as
slave, otherwise the conguration interface cannot be accessed.
● If the GWN7600LR is a slave, make sure to unpair it rst, or do a factory reset.
A computer connected to the GWN7600LR’s SSID, or to the same network as the GWN-
7600LR can discover and access its conguration interface using one of the below methods:
Method 1: Discover GWN7600LR using its MAC Address
1. Locate the MAC address on the MAC tag of the unit, which is on the underside of the
device, or on the package.
2. From a computer connected to same network as the GWN7600LR, type in following ad-
dress using GWN7600LR’s MAC address on your browser https://gwn_<mac>.local
Example: A GWN7600LR with MAC address 00:0B:82:8C:4D:F8 can be accessed by typing
https://gwn_000b828c4df8.local on the browser.
ACCESSING THE CONFIGURATION INTERFACE
Using one of the above methods, the login screen will appear. Type in “admin” in both
Username and Password elds and click on Sign In.
Please download GWN7600LR User Manual and check out FAQ
for more detailed instructions:
http://www.grandstream.com/our-products

~7~ ~8~
概述
此远程无线Wi-Fi接入点是为支持更大的信号覆盖面而设计的。此设备凭借着良好的防水和耐
热技术成为了户外Wi-Fi的理想设备。GWN7600LR利用聚束技术支持双频段的2x2:2MU-MI-
MO，同时利用复杂的天线设计以提供最大化的网络吞吐量以及高达275米的Wi-Fi覆盖面。
为保证安装和管理的简易性，GWN7600采用无控制器的分布式网络管理设计。通过在产品
的网页用户界面中嵌入控制器，实现每个接入点在保证不会产生故障点的情况下，无需借助
其他控制器硬件/软件就能独立管理由多达30个GWN76xx系列AP构成的网络。凭借着安装和
管理的简易性以及支持大面积覆盖和其他优越的性能，GWN7600LR成为了理想的部署中型
无线网络的企业级无线AP。
1 x GWN7600LR 无线接入点
1 x 快速安装手册
1 x GPL 声明
4 x 螺丝 (PM8 x 115)
4 x 防松螺母
4 x 螺丝和螺帽
ZH
1 x 安装支架底座
包装内容
2 x 组合螺丝
1 x 安装支架后盖
1 x 六角扳手
GWN7600LR 端口
Port Description
NET/POE 以太网RJ45端口（10/100 /1000Mbps），需要支持PoE 。
NET 以太网RJ45端口（10/100 /1000Mbps），连接至路由器或另一个
GWN76xx。
RESET 恢复出厂设置按钮。按7秒恢复出厂默认设置。
上电和连接 GWN7600LR
网络端口 RJ45电缆连接到以太网供
电的（PoE）交换机或者
PoE供电转换头。
●不要尝试打开，拆解或修改设备。
●不要将本设备暴露在温度-30℃至60℃以外。
●不要将本设备暴露在环境湿度如下范围以外：10-90％RH（无冷凝）。
●系统启动或固件升级期间不要中断电源。这可能会损坏设备固件，并导致设备故障。
注意事项
通过如下方式可对GWN7600LR 进行PoE供电：
Step 1:
将以太网电缆的RJ45端口插入GWN7600LR的网络端口中；
Step 2:
将电缆的另一端插入交换机的PoE级联端口。

~9~ ~10~
横杆安装
硬件安装
GWN7600LR可以安装在横向和纵向杆子上。
请按照如下步骤进行正确安装。
纵杆安装
4. 将以太网电缆RJ45连接到GWN7600LR正确的端口,并合上接口后盖。
5. 将GWN7600LR对准安装支架底座并自上而下卡入直至主机背面的定位柱顶住底座。
6. 将2颗组合螺丝拧入主机背面的螺孔中，直至GWN7600LR牢牢固定在安装支架上。
1. 将4个(PM8)螺丝插入安装支架后盖的四个螺丝孔中备用。
2. 将装有螺丝的安装支架后盖的凹槽对准将要安装GWN7600LR的纵杆并卡入。
3. 利用安装包内的防松螺母和（PM8）螺丝，将安装支架后盖和安装支架底座组装起来。
1. 将4个(PM8)螺丝插入安装支架后盖的四个螺丝孔中备用。
2. 将装有螺丝的安装支架后盖的凹槽对准将要安装GWN7600LR的横杆并卡入。
3. 利用安装包内的防松螺母和（PM8）螺丝，将安装支架后盖和安装支架底座组装起来。
4. 将以太网电缆RJ45连接到GWN7600LR正确的端口,并合上接口后盖。
5. 将GWN7600LR对准安装支架底座并自上而下卡入直至主机背面的定位柱顶住底座。
6. 将2颗组合螺丝拧入主机背面的螺孔中，直至GWN7600LR牢牢固定在安装支架上。
123
45
12
3
45

~11~ ~12~
连接到GWN7600LR默认的无线网络
新的GWN7600LR会有默认的WiFi广播。 恢复出厂设置也能使默认WiFi启动。
将GWN7600LR上电起机并连接至网络，GWN7600LR会广播默认的SSID。该SSID是基于
设备的MAC地址后六位： GWN[MAC后六位]，并且使用随机的密码。
注意：GWN7600LR的默认SSID和随机密码打印在设备的MAC地址贴纸上。
This device has not been authorized as required by
the rules of the Federal Communications Commission.
This device is not, and may not be,
offered for sale or lease, or sold or leased,
until authorization is obtained.
GWN7600LR
SSID:GWNXXXXXX
S/N XXXXXXXXXXXXXXXX
MAC XXXXXXXXXXXX
WiFi Password: XXXXXXXX
( ) P/NNN XXX-XXXXX-XXXXX
48V 0.5A GigE POE
方法2：用GWNDiscoveryTool发现GWN7600LR。
1. 从下面的连接下载GWNDiscoveryTool: http://www.grandstream.com/support/tools
2. 打开GWNDiscoveryTool，并点击Scan（扫描）。
3. 这个软件将帮助你发现局域网下所有的GWN7600LR并显示他们MAC地址和IP地址。
4. 点击Manage Device（管理设备）后，你将被引导到GWN7600LR的配置界面。或者也可
以通过在浏览器中输入所查找到GWN7600LR的IP地址。
备注 :
●确认GWN7600LR并没有被配对到另一个GWN76XX无线AP，否则配置界面将会显示设
备已配对，导致无法登陆配置页面。
●如果GWN7600LR已经被配对，请从它的配主那里解除配对，或者恢复该设备的出厂设
置。
将电脑连接到GWN7600LR广播的无线网，或GWN7600LR所在的局域网。就可以用以下的
几种方式来发现并访问GWN7600的配置页面：
方法1：用MAC地址来发现GWN7600LR。
1. 在设备的背面的贴纸上，或者设备的外包装盒上可以找到设备的MAC地址。
2. 在连接到GWN7600LR广播的无线网，或GWN7600LR所在的局域网的电脑上，用浏览器
输入网址：https://gwn_<mac>.local
比如：如果GWN7600LR的MAC地址为00:B8:8B:7E:7E:7E，那么则输入
https://gwn_00b88b7e7e7e.local
访问配置页面
使用上面所述的一种方法，你会看到一个登陆界面。在用户名和密码均输入默认的”admin”，
点击Sign in （登陆）。
欲获取详细的话机使用信息，请在以下链接中下载GWN7600LR用户手册。
http://www.grandstream.com/support