Grant SV200 User manual

Features
1. Alarm Light
2. Display
3. F (function) Button
4. Heater On Light
5. S (select) Button
6. Dial
7. Clamp and cage
8. Float: low liquid level protection
Important Safety Information
 Read this quick start guide in full. Safety may be impaired if it is not followed.
 Only connect to the voltage and frequency shown on the serial number plate. An earth is required.
 The SV200 is designed for use with water only.
 Safety can only be assured if the SV200 is clamped firmly to a vessel with suitable stability and robustness and
placed on a level non-combustible surface.
 Ensure the SV200 is positioned so that the plug is easily accessible for disconnection.
 Before moving or cleaning, allow the unit to cool down and disconnect from the power supply.
 Do not use the SV200 to heat any material that could cause fire or any other hazard.
 When using the SV200 at temperatures above 60˚C, use a cover where possible to avoid excessive evaporation.
 The alarm light warns that the SV200 is in a state that could be cause harm. Care should be taken when
investigating the warning.
3. Press S to
store value
Setting the temperature
2. Rotate dial to
desired temp
1. Press S: Display
will flash
30449 V4 Mar 2013
SV200 Universal stirred heater for sous vide cooking
Quick Start Guide
Configuring and running a temperature preset
The SV200 contains three presets which can be configured to
commonly used temperatures.
To set a preset temperature:
1. Press F, rotate the dial until ‘t-1’ is shown, press S to select.
2. Rotate the dial to define the temperature, press S to set.
Repeat for presets 2 and 3.
To run a preset:
1. Press F, rotate dial until required preset is displayed
2. Press S twice to begin running the preset
Clean the unit with a damp cloth, using only water. Do not
use chemical cleaning agents. Do not submerge unit in water.
Do not immerse or de-scale the clamp. Scale on the cage
and heater element can be removed using a chemical de-
scaling product designed for use on kitchen equipment with
metal parts. Warning: de-scaling products maybe toxic.
Follow manufacturers instructions.
Do not wash the clamp and cage in a dishwasher.
If anything is spilt into the equipment, disconnect it from the
power supply and have it checked by a competent person.
Cleaning
1
3
2
5
4
7
6
8
Service Department,
Grant Instruments (Cambridge) Ltd
Shepreth, Cambridgeshire, SG8 6GB, UK
T: [phone]
F: [phone]
E: [email protected]
W: www.grantinstruments.com
1. Press Ftwice –the display will show “Cloc”.
2. Press Sto select.
3. Rotate dial to select “On”. Press Sto select. The dis-
play flashes with time (in minutes) rotate the dial to set
time required (1 to 6000min).
4. Press Sto save. The display alternates between bath
temp and time remaining.
5. An alarm will sound when the countdown timer reaches
zero. “End” will be displayed. Press F or Sto accept.
Setting a countdown timer

Service Department,
Grant Instruments (Cambridge) Ltd
Shepreth, Cambridgeshire, SG8 6GB, UK
T: [phone]
F: [phone]
E: [email protected]
W: www.grantinstruments.com
30449 V4 Mar 2013
SV200 Universal stirred heater for sous vide cooking
Quick Start Guide
Attaching the clamp/cage
1
2
1. Place clamp/cage over locating threads on base of
SV200. Secure using retained nuts. Hand tighten
only.
2. Add clamp rear fixings to secure clamp/cage to rear of
SV200.
Attaching the SV200 to a vessel
Take care not to over tighten the clamp, to avoid damag-
ing the clamp or vessel.
Safety cut out and alarm light
The SV200 is fitted with a float switch which monitors the liquid level during operation. Should the liquid level drop below a
certain level, the safety cut out will be activated and alarm light will appear. Top up the bath with liquid until at least a
minimum level to resume operation.
Conditions for use
The SV200 is a Sous Vide immersion thermostat
designed for indoor use by a professional user in
the following environment:
Ambient temp range 5°C to 40°C
Maximum relative
humidity
80% RH up to 31°C
decreasing to 50% RH at 40°C
Altitude Up to 2,000m (6,500ft)
Electrical details
Mains supply 220-240V @ 50/60Hz
120V @ 50/60Hz
Pollution degree: 2
Installation category: II
Max current consumption 6.5A for 220-240V
12.5A for 110-120V
Mains supply voltage fluctuations are not to exceed
±10% of the nominal supply voltage.
Guarantee, service & repair
When used according to these operating instructions, the
SV200 is guaranteed for 1 year against faulty materials or
workmanship. For service or repair please contact our
Service Department or your local distributor. All returned
units must be accompanied by a Return Materials
Authorisation (RMA) number, obtainable by contacting the
Grant service department.
Product performance
Settable temp range 0°C to 100°C
Temperature stability ±0.05°C
Temperature uniformity ±0.1°C
Heater power 1.3kW for 220-240V
1.4kW for 110-120V
Check that the float is operating correctly before each use. Ensure no grease or foreign objects are preventing the float from
working during operation.
Routine maintenance check