GRAUPNER ULTRAMAT AC/DC EQ User manual

OPERATING INSTRUCTION
Prior to use, please read this manual thoroughly.
Keep this manual in a convenient place for quick and easy reference.
ULTRAMAT
AC/DC EQ

ULTRAMAT AC/DC EQ
2
BEFORE USE
SUPPROT AND SERVICE
Customer support
Internet sales site
A/S regulation
Warranty regulation
OPENHOBBY A/S CENTER
SAFETY PRECAUTIONS
BOX CONTENTS
SPECIFICATION
FEATURES
CHARGER CONTROL IDENTIFICATION
POWER SOURCE
BATTERY CONNECTION
BATTERY TYPE SELECTION
MEMORY SETUP
NiCd, NiMH BATTERIES CHARGE/DISCHARGE
NiCd, NiMH charge
NiCd, NiMH discharge
NiCd, NiMH cycle
LiPo, LiIon, LiFe BATTERIES CHARGE/DISCHARGE
LiPo charge
LiPo discharge
LiPo cycle
LiPo store
LiPo balancer
Pb CHARGE/DISCHARGE
Pb charge
Pb discharge
DISPLAYS DURING CHARGE/DISCHARGE
ERROR MESSAGES
BATTERY CHARGE TIME CALCULATION
NEW BATTERY CHARGE
Pb BATTERY SAFETY
LiIon, LiPo, LiFe BATTREIES SAFETY
ENVIRONMENT PROTECTION NOTES
SAFETY APPROVAL
3P
3P
3P
3P
3P
3P
3P
4P
4P
5P
5P
6P
6P
7P
7P
8~9P
9~10P
9P
10P
10~11P
11P
12P
12P
13P
13~14P
14P
14~15P
14P
15P
15~16P
16~17P
17P
17P
18P
18~19P
19P
19P
Contents

ULTRAMAT AC/DC EQ
3
◎ BEFORE USE
◎ SUPPORT AND SERVICE
◎ OPENHOBBY A/S CENTER
Thank you for purchasing ULTRAMAT AC/DC EQ charger.
This system is extremely versatile and may be used by beginners and pros alike. In
order for you to make the best use of your system, please read this manual carefully. If
you have any difculties while using your system, please consult the manual, our online
Frequently Asked Questions (on the web pages referenced below), your hobby dealer, or
the Graupner/SJ Service Center.
Due to unforeseen changes in production procedures, the information contained in this
manual is subject to change without notice.
8F, 202 Dong, Chunui Techno-Park II, 18, 198 street, Bucheon-ro, Wonmi-Gu,
Bucheon-Shi, Gyungki-Do KOREA 420-857
Phone: [phone] Fax: [phone]
Customer Service E-mail: [e-mail]
Internet sales site
Warranty regulation
Refer the WARRANTY CARD in a Package.
Customer support
Please feel free to ask any question by e-mail or phone. We’ve been trying to deal
with your question. We are open from nine to six, Monday to Friday in Korea. We may
respond to your question by e-mail as soon as possible when we are close.
A/S regulation
Only when the product is faulty after normal operation within the warranty period, we
will repair the product for free based on our regulations. The repair will be paid for by
the consumer when the damage is due to use in improper ways or beyond the warranty
period.
Please feel free to contact “www.openhobbby.com” to get all information on
product features, specications, running events and the newest product line up.

ULTRAMAT AC/DC EQ
4
◎ ◎◎ ◎◎◎
◎ BOX CONTENTS
◎ SAFETY PRECAUTIONS
1. Do not attempt to charge incompatible types of rechargeable batteries. This charger is
designed to only charge and discharge Nickel Cadmium, Nickel Metal Hydride, Lithium
Ion, Lithium Polymer, and Lead Acid batteries.
2. Do not attempt to charge a dead or damaged battery.
3. 12V input from Pb battery or reliable 12V power supplier that can supply more than 7A
current is needed
4. Make sure to place the charger on a rm level surface for charging.
5. Do not attempt to charge batteries at excessive fast charge currents. Check with your
battery manufacturer for the maximum charge rate applicable to your battery.
6. Do not allow water, moisture or foreign objects into the charger and use in a well venti-
lated area
7. Do not place the battery or charger on or near a ammable object while in use. Keep
away from carpets, cluttered workbenches, etc.
8. Do not leave the charger unattended while charging. Disconnect the battery and remove
input power from charger immediately if the charger becomes hot and keep the charger
and battery cool down before reconnecting. Young children should be supervised to
ensure that they use the appliance safely
9. Do not disassemble the charger.
10. If lead-acid battery is used to charge battery, the battery terminal shouldn’t be contact-
ed to the chassis
11. Do not use automotive type battery chargers to power the charger.
12. Do not cover the air intake holes on the charger as this could cause the charger to
overheat.
13. Connect the input leads to a 12V power supply rst, then connect the battery.
14. Do not attempt to charge non-rechargeable batteries.
15. Please comply with LiIon, LiPo, LiFe safety before charging
16. Do not use the damaged AC Power cord.
1. Charger 1EA
2. AC Power cord 1EA
3. Balance board 1EA
4. Balance cable 1EA
5. Charge cable 1set (RED/BK)

ULTRAMAT AC/DC EQ
5
1. Built in micro processor controls charge/ discharge, storage, balance system
2. NiCd, NiMH, LiIon, LiPo, LiFe, Pb batteries are available. Max 80W charge
3. NiCd and NiMH: Delta peak detection system, Lithium and Pb: Voltage detection
system
4. 2-line, 16 black & white backlit character LCD
5. Selectable 3.6V or 3.7V or 3.3V, 1~6 cells LiIon battery
6. Support 0.1A~7.0A charge current, NiCd / NiMH 1-14cells, 1.2-16.8V
7. Support 10~1000mA discharge current, NiCd / NiMH 1-14cells, 1.2-16.8V
8. Support cycle mode (Charge to discharge / Discharge to charge).
9. Prevent form reverse connecting of Input, output terminal. Built in cell balancer
10. Built in DC 12V, 5.0A power supplier, 110-220V AC input.
◎ SPECIFICATION
◎ FEATURES
11.0-15.0V DC or AC 100V ~ 240V / 50 ~ 60Hz
NiCd 1-14 cells / NiMH 1-14cells
LiIon 1-6 cells/LiPO 1-6 cells, LiFe 1-6 cells (Type:3.6V or 3.7V or 3.3V )
Pb Batt 1-6 cells ( 2V per cell )
100mAh ~ 9900mAh NiCd NiMH
100mAh ~ 50000mAh adjustable ONLY for LiIon, LiPo and LiFe
0.1A ~ 7A in 100mA steps (DC:80W, AC : 50W)
0.1A ~ 1A in 100mA steps (auto limited to 5W maximum)
0 ~ 200mA
Max. 280mA
“zero delta V” peak detection for NiCd/NiMH
“constant current / constant voltage”for LiIon/ LiPo/ LiFe and Pb
3mV ~ 25mV for NiCd & NiMH batteries per cell
Charge to Discharge / Discharge to Charge
2-line, 16 black&white backlit character LCD
160 x 152 x 69 mm / 6.30 x 5.98 x 2.72 in
684 g / 24.13 oz
10
Input Voltage
Battery Type & Cells
Battery Capacity
Charge Current
Discharge Current
Trickle Charge Current
Balancing Current
Charge Termination
Cycling
Delta Peak Sensitivity
Display Type
Dimensions
Weight
Memory

ULTRAMAT AC/DC EQ
6
1. Connect charger to 12V DC power supply or AC110-220V
2. Connect the charger’s red alligator clip to the positive (+) terminal on the power source
and the black alligator clip to the negative (-) terminal. In case of DV 12V input, charg-
er will display “INPUT BATTERY VLOTAGE ERROR” message if the input is below
11V or above 15V. In this case, please recheck the input power supply to make sure
adequate power is present.
If AC power is being used as input power, do NOT try to connect the 12V DC power!
◎ CHARGER CONTROL IDENTIFICATION
◎ POWER SOURCE
2-line, 16 character LCD
AC Input
- Output
AC lnput
- Output
+ Output
+ Output
Balancer port
Balancing port
Buttons

ULTRAMAT AC/DC EQ
7
Nixx
LiFe
LiPo
Lilon
Pb
Lithium batteries need to balance for more safety, if lithium batteries are charged
without balance board, the balancing of lithium batteries is not performed.
◎ BATTERY TYPE SELECTION
◎ BATTERY CONNECTION
Connect charge cable to 4mm output banana sockets on charger with attention to polarity,
red +, black –. If battery is not connected to charger correctly, the error message is ap-
peared
- No battery : When a battery is not connected to the charger’s output
- Open circuit : When a battery becomes disconnected during an operation
- Reverse polarity : When a battery is connected to the output in reverse
When the power supplier is connected to the charger the below screen is displayed and
the Setup screen is displayed after about 1 second
Press BATT TYPE button twice to select Battery type
※ The programming setup is applied differently when you press START/STOP button less
than 1 Sec and longer than 1 Sec
Press ENTER button then battery type blinks and press ENTER button again then
other value blinks. If you leave it for more than 3 sec without operating, the blinking is
stopped. Press and hold ENTER button to start charge or discharge.
Pole
LiPo
Ultramat AD EQ
Graupner/SJ 1.00
Pole
Nixx
Pole
LiPo
Pole
LiFe
Pole
Lilo
Pole
Pb
2S
6S
3S
3S
3S
12V
[01]
800
[01]
3000
[01]
3000
[01]
3000
[01]
3000
[01]
pack
CAUTION

ULTRAMAT AC/DC EQ
8
◎ MEMORY SETUP
ULTRAMAT AC/ DC EQ has 10 memories
It is used to store specic battery, charge, discharge and safety parameters, as well as
being used to initiate charging, discharging, cycling/store mode functions
① Press ENTER button then the memory number blinks. Press INC/DEC buttons to select
the memory number.
② Press ENTER button then BATTERY TYPE blinks. Press INC/DEC buttons to select
battery type.
④ Press ENTER button and INC/DEC buttons to set battery capacity.
③ Press ENTER button then battery cell blinks. Press INC/DEC buttons to set battery cell.
⑤ Press ENTER button to remove the curser blinking.
⑥ Press INC/DEC buttons to set charge current and charge voltage and then press EN-
TER button to remove the curser blinking.
⑦ Press INC button to access to DISCHARGE mode and press INC/DEC buttons to set
discharge current and discharge voltage and then press ENTER button to remove the
curser blinking.
Pole
LiPo
Pole
LiPo
Pole
LiPo
Pole
LiPo
Pole
LiPo
LiPo
C=3.0A
6S
6S
6S
6S
6S
[01]
3000
[01]
3000
[01]
3000
[01]
3000
[01]
3000
CHARGE
4.2V/C
LiPo
D=1.0A
DISCHARGE
3.0V/C

ULTRAMAT AC/DC EQ
9
- NiCd, NiMH charge
① Go to Nixx mode
② Press INC button to access to CHARGE mode
③ Press ENTER button shortly then the value of charge current blinks, press DEC/INC
buttons to set the desired value of charge current.
④ Press ENTER button then the value of delta peak blinks, press DEC/INC buttons to
set the desired value of delta peak.
⑤ Press and hold ENTER button to start charge battery.
⑧ Press INC button to access to CYCLE mode and press INC/DEC button to charge/dis-
charge sequence and repeating number and then press ENTER button to remove the
curser blinking.
⑨ Press INC button to access STORE mode and press INC/DEC buttons to set charge/
discharge and then press ENTER button to remove the curser blinking.
⑩ Press INC button to access to BLANCER mode and check if the setup is correct.
◎ NiCd, NiMH BATTERIES CHARGE/DISCHARGE
LiPo
C=3.0A
LiPo
C=3.0A
LiPo
(03)CELL
CYCLE D->C1
D=1.0A
STORE
D=1.0A
BALANCER
START
Prole
Nixx 5S
Nixx
C=3.0A
Nixx
C=3.0A
Nixx
C=3.0A
[01]
3000
CHARGE
d=25mV/c
CHARGE
d=25mV/c
CHARGE
d=25mV/c
BATTERY
PLEASE
CHECK
WAIT....

ULTRAMAT AC/DC EQ
10
- NiCd, NiMH cycle
① Go to Nixx mode
② Press INC button 3 times to access to CYCLE mode
③ Press ENTER button shortly then the cycle sequence blinks, press DEC/INC buttons
to set the desired cycle sequence
④ Press ENTER button then the number of cycle blinks, press DEC/INC buttons to set
the desired number of cycle
※ D->C : Discharge to Charge/ C->D : Charge to Discharge
- NiCd, NiMH discharge
① Go to Nixx mode
② Press INC button twice to access to DISCHARGE mode
③ Press ENTER button shortly then the value of discharge current blinks, press DEC/
INC buttons to set the desired value of discharge current
④ Press ENTER button then the value of discharge cutoff voltage blinks, press DEC/
INC buttons to set the desired value of discharge cutoff voltage
※ We recommend battery cells x 0.9V as the discharge cutoff voltage
⑤ Press and hold ENTER button to start discharge battery
Prole
Nixx
Nixx
D=1.0A
Nixx
D=1.0A
Nixx
D=1.0A
BATTERY
PLEASE
Prole
Nixx
Nixx
C=3.0A
Nixx
C=3.0A
5S
5S
[01]
3000
DISCHARGE
0.8V/C
DISCHARGE
0.8V/C
DISCHARGE
0.8V/C
CHECK
WAIT....
[01]
3000
CYCLE C->D1
D=1.0A
CYCLE C->D1
D=1.0A
Nixx
C=3.0A
CYCLE C->D1
D=1.0A