GRAUPNER Kingpad mc-edition mc-26 Owner's manual

EN
Programming manual
Part 2
mc-26 / mc-28 / mc-28 4D
MC-28
MC-28
MC-28 MC-28
esc set
No. S1036 / 33028 / S1033
16 channel HoTT 2,4 GHz transmitter

3 / 80
33028_mc_28_Teil2_jh
Index
Introduction............................................................................. 7
Service Centre................................................................................7
Use and menu functions......................................................... 8
Short-Cuts ......................................................................................8
Definition of terms .................................................................. 9
Receiver configuration .......................................................... 10
Fixed-wing models .......................................................................10
Helicopter models.......................................................................11
Vehicles, boats .............................................................................11
Copter ..........................................................................................12
Receiver power supply.................................................................12
Symbols explication .............................................................. 13
Menus description ................................................................ 13
Meaning of the warnings...................................................... 13
Model selection..................................................................... 14
Copy/Delete........................................................................... 15
Export to SD card .........................................................................16
Import from SD ............................................................................16
Suppress menus .................................................................... 18
Suppress models ................................................................... 18
Model basic settings ............................................................. 18
Control mode ...............................................................................19
Binding type .................................................................................19
Module.........................................................................................20
Receiver binding ..........................................................................21
Receiver output ...........................................................................22
RF module ....................................................................................22
Range test ....................................................................................22
DSC port .......................................................................................23
Throttle Cut..................................................................................23
Switch-on warning .......................................................................24
Auto trim......................................................................................24
Timer auto reset ..........................................................................24

4 / 80 33028_mc_28_Teil2_jh
Model type ............................................................................ 25
Motor on CH1 ..............................................................................26
Tail ................................................................................................26
Ailerons/Flaps ..............................................................................27
Brake offset ..................................................................................27
Servo adjustment .................................................................. 27
Sticks setting.......................................................................... 29
Controls setting ..................................................................... 29
Dual Rate / Expo.................................................................... 31
Throttle curve ........................................................................ 32
Switch display........................................................................ 34
Control switch........................................................................ 34
Logical switch......................................................................... 35
Announce............................................................................... 35
Phase setting ......................................................................... 36
Motor ...........................................................................37
Phase assignation.................................................................. 38
Phase trim.............................................................................. 38
Channels without delay ........................................................ 39
Timers (general) .................................................................... 39
Phase timer............................................................................ 41
Wing Mix................................................................................ 42
Programming of the wing type....................................................43
Model type: "1AIL" ......................................................................43
Model type: "1AIL 1FLAP"............................................................43
Model type: "2AIL" ......................................................................44
Model types with "2/4AIL 1/2/4FLAP" ........................................45
Model type: "2AIL 1FLAP"............................................................45
Model type: "2AIL 2FLAP"............................................................45
Model type: "2AIL 4FLAP"............................................................46
Model type: "4AIL 2FLAP"............................................................46
Model type: "4AIL 4FLAP"............................................................47
Multiflaps menu...........................................................................48
Brake setting ................................................................................50
AIL-> RUD (aileron-> rudder).......................................................52

5 / 80
33028_mc_28_Teil2_jh
FLAP-> ELE (flaps-> elevator).......................................................52
Free mixers ............................................................................ 53
MIX act. / Phase .................................................................... 56
Only mix channel................................................................... 56
Dual mixer.............................................................................. 57
Fail Safe.................................................................................. 57
Trainer.................................................................................... 58
Transmitter output................................................................ 58
Profitrim................................................................................. 59
Trim memory ......................................................................... 60
Telemetry............................................................................... 60
Channel sequencer................................................................ 61
Multichannel ......................................................................... 62
MP-3 Player ........................................................................... 64
Basic settings ......................................................................... 64
Loudspeaker (LS) Voice / Vario / Buttons ....................................64
Owner ..........................................................................................64
Control mode (preset) .................................................................65
Stick-type (only by mc-26) ...........................................................66
Module.........................................................................................66
DSC port .......................................................................................66
Pitch min ......................................................................................66
Contrast (upper/lower display)....................................................66
Display light..................................................................................66
Switch-on melody ........................................................................67
Battery alarm threshold...............................................................67
Switch-on warning .......................................................................67
Touch sensitivity...........................................................................67
DATA sel........................................................................................67
Ph. Name 1 … 10..........................................................................67
BT headset and following lines ....................................................67
Vibration ................................................................................ 68
Servo display.......................................................................... 68
Servo test ............................................................................... 68
Key lock .................................................................................. 68

6 / 80 33028_mc_28_Teil2_jh
Info display ............................................................................ 69
Digital trim / Throttle switch-off trim (function) ................ 69
Heli programming.................................................................. 70
Throttle curve (Heli).............................................................. 73
Sticks setting (Heli)................................................................ 73
Control adjust (Heli) .............................................................. 73
Ring limit................................................................................ 75
Firmware update................................................................... 76
Update through memory card.....................................................76
Update through USB port............................................................77
Problems during firmware update ..............................................77
Declaration of conformity..................................................... 77
Notes on environmental protection..................................... 78
Care and maintenance .......................................................... 78
Warranty................................................................................ 78

7 / 80
33028_mc_28_Teil2_jh
Introduction
Thank you very much for purchasing the Graupner mc-28 HoTT.
The transmitter manual is composed by two parts. Part 1, the short
manual, is included in the packaging. Part 2, the programming man-
ual, can be found in its last version on www.graupner.de by the
related page of the transmitter.
Read this manual carefully to achieve the best results with your
transmitter and first of all to safely control your models. If you expe-
rience any trouble during operation, take the instructions to help or
ask your dealer or Graupner Service Centre.
Due to technical changes, the information may be changed in this
manual without prior notice. Keep updated by regularly checking
our own website, www.graupner.de to be always updated with
the products and firmware.
Service Centre
Graupner Central Service
Graupner/SJ GmbH
Henriettenstraße 96
D-73230 Kirchheim/Teck
Servicehotline

(+49) (0)7021/722-130
Monday- Thursday:
9:15 am- 4:00 pm
Friday:
9:15 am- 1:00 pm
[e-mail]
Graupner USA
3941 Park Dr Suite 20-571
El Dorado Hills, CA 95762
Website: www.graupnerusa.com
Phone: [phone]
Email:[email protected]om
Graupner in Internet For the service centers outside Germany please refer to our web site
www.graupner.de

8 / 80 33028_mc_28_Teil2_jh
Use and menu functions
Short-Cuts
The following key combinations can be used to directly call up cer-
tain menus and options:
CLEAR
Brief simultaneous touch of the keys or on the right touch pad
will restore the active entry fi eld's changed parameter value back to
its default value.
"Servo screen"
Brief simultaneous activation of the keys of the left touch pad will
cause a jump from the transmitter's base screen or from almost any
menu position to the "Servo" menu.
"Telemetry" menu
Press the center ESC key in the left touch pad for about 1 s to call up
the "Telemetry" menu from the transmitter's base screen.
To come back to the base screen it is enough a "normal" touch on
the ESC key.
Graphic display of telemetry data
Briefly touching one of the selection keys of the left or right touch
pad will cause a jump from the base screen directly to the transmit-
ter's graphic display of telemetry data or will allow paging back and
forth between individual graphic displays.
Briefly touching the ESC or SET key will cause a return back to the
base screen.
"HIDDEN MODE"
Press and hold arrow keys of the left touch pad then momentarily
touch the SET key of the right touch pad.
Key lock
Entry lockout is activated and deactivated from the base screen by
simultaneously pressing the ESC and SET keys for about two seconds.
The key lock function is displayed by a key symbol:
The controls remain operational.
Press the ESC and ENT buttons at the same time again for about two
second to release the lock.
Quick-Select
From the multi-function list, a jump can be made to a "Structure
overview" by a brief, simultaneous touch on the or keys of the
right touch pad.

9 / 80
33028_mc_28_Teil2_jh
Definition of terms
Control function
A control function is understood as the signal for a specific control
function. The signal of a control function can be transmitted directly
into one control channel or through a mixer to several control chan-
nels. The control function includes the influence of the mechanical
control path on the corresponding servo. This can be spread or con-
centrated and modified from linear to highly exponential.
Controls
As "control" are meant the function elements that the pilot can actu-
ate directly in the transmitter. Through the controls the connected
servos, ESC etc. will be controlled by the receiver.
Control channel
If a signal contains all control information necessary for a particular
servo, whether directly from the control or indirectly via a mixer,
then the term control channel is used.
Mixer
The transmitter software contains a variety of mixing functions.
These allow a control function to influence several control channels
and several servos. It is also possible to let several control function
influence control channel (one servo).
Switch
The series of toggle switches can be included in the control program-
ming. The switches are however generally also intended to switch
program options such as to start and stop the timers, turn mixers on
and off, as trainer switches etc. Each of the switches can be assigned
any number of functions.
Control switch
In these software switches, labelled with "G1 ... G8", the switching
point within the control travel can be set by simply pushing a button.
Logical switch
Through this option two switches, controls and logical switches or
the favorite combination of them, can be interconnected in an "AND"
or "OR" switch. A total amount of 8 logical switches "L1 … L8" can be
programmed.
Fix switch FXI and FX
This kind of switch switches a function always on or off. You can also
assign to a control function a fix input signal, e.g. FX = +100 % and
FXi =-100 %.

10 / 80 33028_mc_28_Teil2_jh
Receiver configuration
The servos must be connected to the receiver in the indicated
sequence. Not assigned outputs remain free. It is possible to change
the settings in the line "Receiver outputs" in the "Model basic set-
ting" menu.
Fixed-wing models
Fixed-wing models with and without a motor with up to 4 ailerons
and up to 4 flaps and tail type "normal" or "2 elevator servos"
Tail type "V tail
Delta/flying wing models with and without a motor with up to 4
ailerons/elevators and 4 flap/elevator servos
receiver power supply
free or AILE2 left or special function
free or AILE2 right or special function
aileron or aileron left
free or special fucntion
receiver power supply
airbrake or engine servo or drive controller
aileron right or special function
flap or flap left
flap right or free or special function
free or FLAP2 left or special function
free or FLAP2 right or special function
elevator/rudder left
elevator/rudder right
receiver power supply
free or special function
free or special function
aile/elev left
aile/elev right
free or special function
receiver power supply
Airbrake or motor servo
or ESC for electric models
free or special function
fre or flap / elev left
free or flap / elev right
free or special function or flap 2 / elev left
free or special function or flap 2 / elev right
free or rudder
receiver power supply
free or AILERON2 left or special function
free or AILERON2 right or special function
rudder
AILERON or AILERON left
elevator or elevator1
free or 2nd elevator or special function
receiver power supply
Airbrake or engine servo or electric drive controller
AILERON right or special function
FLAP of FLAP left
FLAP right or free or special function
free or FLAP2 left or special function
free or FLAP2 right or special function

11 / 80
33028_mc_28_Teil2_jh
Helicopter models
Receiver assignment for helicopter models with 1 to 3 swashplate
servos
Receiver assignment for helicopter models with 4 swashplate ser-
vos
Vehicles, boats
receiver power supply
free or special function
free or special function
tail servo (gyro-system)
Roll-1-servo
Nick-1-servo
free or governor or special function
receiver power supply
Pitch- or Roll-2 or Nick-2-servo
free or special function
throttle servo or motor controller
gyro suppression
free or special function
free or special function
receiver power supply
free or special function
free or special function
Tail-servo (gyro-system)
Roll-1-servo
Nick-1-servo
free or governor or special function
receiver power supply
Roll-2-servo
Nick-2-servo
throttle servo or motor controller
gyro suppression
free or special function
free or special function
receiver power supply
free or special function
free or special function
free or special function
steering (left/right function)
free or special function
free or special function
receiver power supply
engine servo or speed controller (forward/backward)
free or special function
free or special function
free or special function
free or special function
free or special function

12 / 80 33028_mc_28_Teil2_jh
Copter
Receiver power supply
receiver power supply
free or special function
free or special function
Yaw
Roll
Nick
free or special function
receiver power supply
Motor/Pitch (up/down)
free or special function
free or special function
free or special function
free or special function
free or special function
special function
V-cable
No. 3936.11
PRX stabilized
receiver power
supply No. 4136
special function
V-cable
No. 3936.11
PRX stabilized
receiver power supply
No. 4136

13 / 80
33028_mc_28_Teil2_jh
Symbols explication
Always observe the information indicated by this warning sign. Par-
ticularly those which are additionally marked with the CAUTION
or WARNING. The signal word WARNING indicates the poten-
tial for serious injury, the signal word CAUTION indicates possibil-
ity of lighter injuries.
The signal word Note indicates potential malfunctions.
Attention indicates potential damages to objects.
Menus description
The menus are described in the same sequence as they appear in
the lower display. Tap on the SET button in the base display to switch
in the multifunction menu.
The chapters of the manual are marked with model type symbols.
The symbols are exactly the same used in the transmitter. It shows
you which paragraph is related to your model type. Thus makes it
easier to find which paragraph is required for each model program-
ming.
Meaning of the warnings
Transmitter input voltage too low
"Bind?"
No receiver is bound to the actually active model memory. By
shortly tapping the SET button you can accede the related option.
You want to perform a model change in the "Model select"menu
but the receiver of the actually active model is however still
switched on.
No bound receiver in range.
Should the RF transmission be switched "ON" or "OFF"?
It appears only after switching the transmitter on with already
bound receiver in active model memory.
Request to switch the RF transmission off
!
Battery
needs
charging !!
BIND?
OK
Warning!
Switch OFF the receiver
first!
CAN‘T
RECEIVE
DATA
OK
RF on/off?
OFF
ON
Please select
Switch
RF module
OFF
OK

14 / 80 33028_mc_28_Teil2_jh
Fail Safe setting not performed yet
Throttle or pitch control stick position or throttle limit for helicop-
ters too high
Connection between teacher and pupil transmitter disturbed
No SD or SDHC memory card in the card slot or card not readable.
Within the time set in the line "Switch-on warning" of the "general
settings" menu the transmitter has not been used. In the display it
appears the warning and the WARNING LED on the right side
of the On/Off switch blinks and an acoustic warning alarm is emitted.
If the transmitter is still not being used it will autonomously switch
off after about three minutes.
In case of too low battery voltage a model change is not possible for
safety reasons. In the display appears a related message:
Should the "Wireless Teacher/pupil connection" used before the last
switch off of the transmitter be continued (CONTINUE) or inter-
rupted (INTERRUPT)?
Model selection
Tap on the SET button to access the menu. Now you can see the list
of the available model memories. Selection of the desired model
memory through the or buttons of the left or right touch-pad.
Then tap on the SET button.
Create a new model memory, select an empty model memory:
You will be requested to select the desired model type among the
five available model types.
Select through the or buttons the related symbol and then tap
on the SET button. In this way the selected model memory will be
installed with the selected model type.
Fail-Safe
setup
t.b.d.
Thr
too
high!
No
pupil
signal
insert
SD card
OK
Power-on warning
is active!!!
actually not possible
voltage too low
Please select
Trainer connection?
ON OFF
Copy / Erase
Suppress menus
Suppress models
Model select
Base setup model
Model type
03
04
05
 free
02
01
06
R12
 free
 free
 free
 free
M

15 / 80
33028_mc_28_Teil2_jh
With this selection model specific settings will be available in the
menus. Now you can program your model in this model memory.
After the initialization of the selected model memory with the
desired model type the display changes to the base display of the
new assigned model memory. At the same time it will appear for
some seconds the warning message that there is no connection with
a receiver. Tapping on the SET button you will directly enter the "Base
menu". Here you are directly in the line for binding. For the binding
process, please read the description in the "Model base setting"
menu. Tap on the ESC button to procede without binding.
Copy/Delete
Tap on the SET button to access the menu. Now you can see the list
of the available functions. On the right side of the display there is a
scrollbar. That indicates you that there are other menu points other
than the actually visible ones. Scroll with the selection buttons up or
down.
Delete model
Select the "delete model" point an confirm through the SET button.
On the lower left side you can see an arrow facing down. That indi-
cates you that there are other menu points other than the actually
visible ones. Scroll with the selection buttons up or down.
Note
This deletion cannot be restored. All of the data in the selected
model memory are completely deleted.
If the actually active model memory is deleted, soon after the dele-
tion process it must be defined a favorite model type. If an inactive
model memory is deleted, soon after the model selection appears
"àààfreeààà".
Use the selection buttons  of the left or right touch-pad to select
the model to delete.
It appears a safety query. The deletion process will be performed
only if you move to YES and tap on the SET button. Selecting NO and
tapping on SET button interrupts the deletion process.
BIND?
OK
Select model type
Model select
Base setup model
Model type
Copy / Erase
Suppress menus
Suppress models
Copy phase
Erase model
Copy model–>model
=>
=>
=>
Export to SD
Import from SD =>
=>
=>
=>
01
03
04
05 frei
ULTIMATE
02
GRAUBELE
STARLET
BELL47G
Model to be erased:
R12
R12
R12
–––
M
M
G
M
Model really
GRAUBELE
to be erased ?
NO YES
01

16 / 80 33028_mc_28_Teil2_jh
Copy Mod¢Mod
Select the point "Copy Mod¢Mod" and confirm through the SET
button.
Through the ESC button you can always interrupt the process.
• Select the model to copy and confirm the selection through the
SET button.
• Select the target memory and confirm through the SET button.
It appears a safety query. If you change to YES and press the SET but-
ton, the copy process will be performed. The copy process is inter-
rupted if you select NO.
Export to SD card
Select the "Export to SD" point an confirm through the SET button.
Through the ESC button you can always interrupt the process.
Select the model to export and confirm the selection through the
SET button.
It appears a safety query. If you change to YES and press the SET but-
ton, the export process will be performed. The process is interrupted
if you select NO.
Import from SD
Select the "Import from SD" point an confirm through the SET but-
ton.
Through the ESC button you can always interrupt the process.
• Select the model to export from the SD card and confirm through
the SET button.
• Select the target memory and confirm through the SET button.
It appears a safety query. If you change to YES and press the SET but-
ton, the import process will be performed. The import process is
interrupted if you select NO.
Note
If the imported model memory has been created in the transmitter
and is imported to the same model memory then the receiver con-
nection remains. If the model memory is imported in another trans-
mitter, then the receiver must be bound again.
01
03
04
05 frei
ULTIMATE
02
GRAUBELE
STARLET
BELL47G
Copy from model:
R12
R12
–––
R12
M
M
G
M
Model
ULTIMATE
export ?
NO YES
01
SD-CARD
Copy phase
Erase model
Copy model–>model
=>
=>
=>
Export to SD
Import from SD =>
=>
=>
=>
Model
ULTIMATE
export ?
NO YES
01
SD-CARD
05 frei
EXTRA
ALPINA
COBRA
BELL47G
Import from SD-CARD:
16/08/10
16/08/11
16/08/12
16/08/13
01
03
04
ULTIMATE
02
GRAUBELE
STARLET
BELL47G
Import to model:
05 free
R12
R12
R12
–––
M
M
G
M

17 / 80
33028_mc_28_Teil2_jh
Copy phase
Select the "Copy phase" point an confirm through the SET button.
Through the ESC button you can always interrupt the process.
• Select the phase to copy and confirm the selection through the
SET button.
• Select the target phase and confirm the selection through the
SET button.
A safety query appears. If you change to YES and press the SET but-
ton, the copy process will be performed. The copy process is inter-
rupted if you select NO.
Permanently save changes / undo changes
If you perform a model change or if you switch the transmitter off
the last stand of the programming of the model is saved in the model
memory. With the "Permanently save changes / undo changes"
function the change will be manually edited during the use.
Through the "Permanently save changes / undo changes" menu
point you can immediately save permanently the edited program-
ming in the model memory.
Through the "Permanently save changes / undo changes" menu
point you can undo programming performed during the use. In this
way you can restore the last performed programming. You can
choose since when the undo action should start, between the last
switch-off or the last manual saving.
It appears a safety query. If you change to YES and press the SET but-
ton, the related process will be performed. The process is inter-
rupted if you select NO.
7
Copy to phase:
3
5=>
=>
2
4
6
1
Copy phase
Erase model
Copy model–>model
=>
=>
=>
Export to SD
Import from SD =>
=>
=>
=>
7
Copy from phase:
3
5=>
=>
2
4
6
1
Copy phase
=>
=>
=>
Export to SD
Import from SD
=>
=>
=>
=>
Store changes
undo changes
Copy phase
=>
=>
=>
Export to SD
Import from SD
=>
=>
=>
=>
Store changes
undo changes

18 / 80 33028_mc_28_Teil2_jh
Suppress menus
In this menu you can hide menu points from the menu function list.
The hiding is related to the model memory.
Select the menu point to hide or to show and switch the status
through the SET button. The crossed-out menu points are then no
longer displayed in the multifunction list.
The menu points are not deactivated, programmed functions in the
hidden menus remain active.
Suppress models
In this menu you can hide model memories from the model selec-
tion list.
Select the model memory to hide or to display, tap on the SET but-
ton to switch the status. The crossed-out model memories are then
no longer displayed in the model selection list.
The model memories will not be deactivated, the programmed
options will be retained.
Model basic settings
In this menu you will set the base setting for the actual model mem-
ory.
Model name
You can insert a maximum of nine characters for a model name of
the active model memory.
Through the left and right selection buttons you can move up or
down to the next place. Through the SET button you confirm the
selection and move to the next place. You can insert an empty space
if you tap at the same time on the up and dow or left and right but-
tons.
Through the ESC button you can leave the menu.
Suppress models
Model select
Base setup model
Model type
Copy / Erase
Suppress menus
Model select
Base setup model
Model type
Copy / Erase
Suppress models
Suppress : SET
Model select
Base setup model
Model type
Copy / Erase
Suppress menus
Suppress models
01
03
04
05
ULTIMATE
02
GRAUBELE
STARLET
BELL47G
R12
R12
R12
–––
 free
Suppress : SET
M
M
G
M
Model type
Suppress models
Base setup model
Servo adjustment
Control adjust
Stick mode
Mod. Name
Stick mode
Module
1
n/a
Base setup model
bind
BD2
BD1
Rcv Ch Map n/a
HoTT
R08
!"#$%&’()�+,–./0123
456789:;
Mod Name GRAUB
FGHIJKLMNOPQRSTUVWX
YZ[¥]^_`abcdefghijk
?@ ABCDE

19 / 80
33028_mc_28_Teil2_jh
Control mode
In this function you can choose a control mode which will be used
for this model memory. In this way it will be determined which con-
trol movement of the related control stick will we associated to
which channel. Tap n the SET button, set the desired mode through
the selection buttons. In the "receiver assignation" section you can
see where each servo should be connected.
Binding type
Note
This menu line is only visible until no receiver is bound to the active
model memory.
This option must be selected before the binding of a receiver. You
can select between "Global" and "Model", which means:
"Global": All bound receivers react to the signals of each model
memory of the transmitter. For safety reasons it is then only possible
to change model memory only after having switched the receiver off.
"Model": Bound receivers react only to the signals of the assigned
model memory. An accidental use thorough a non specifically
assigned model memory is not possible.
Mod. Name
Stick mode 1
Base setup model
SEL
GRAUBELE
n/a
bind
Module HoTT
Rcv Ch Map n/a
R08
Fixed-wing model Helicopter model / Copter model
Mod. Name
Control mode 1
Base setup model
SEL
GRAUBELE
n/a
n/a
Module HoTT
Binding type Model
Car / boat
MODE 2 (Throttle left)
Nick
Nick
Tail rotor
Tail rotor
Motor / Pitch
Motor / Pitch
Roll
Roll
Motor / Pitch
Motor / Pitch
Tail rotor
Tail rotor
Nick
Nick
Roll
Roll
Nick
Nick
Roll
Roll
Motor / Pitch
Motor / Pitch
Tail rotor
Tail rotor
Motor / Pitch
Motor / Pitch
Roll
Roll
Nick
Nick
Tail rotor
Tail rotor
MODE 1 (Throttle right)
MODE 3 (Throttle right) MODE 4 (Throttle left)
MODE 2 (Throttle left)
Elevator
Elevator
Rudder
Rudder
Full throttle
Motor idle
Querruder
Querruder
Full throttle
Motor idle
Rudder
Rudder
Elevator
Elevator
Aileron
Aileron
Elevator
Elevator
Aileron
Aileron
Full throttle
Motor idle
Rudder
Rudder
Full throttle
Motor idle
Aileron
Aileron
Elevator
Elevator
Rudder
Rudder
MODE 1 (Throttle right)
MODE 3 (Throttle right) MODE 4 (Throttle left)
MODE 2 (for/backward left)
left
right
forward/backward
forward/backward
forward/backward
forward/backward
left
right
forward/backward
forward/backward
left
right
forward/backward
forward/backward
left
right
MODE 1 (for/backward right)
MODE 3 (for/backward right) MODE 4 (for/backward left)

20 / 80 33028_mc_28_Teil2_jh
The binding type is indicated in the model memory list near the
model memory name:
"G" means global binding
"M" means model memory specific binding
Module
Through the left and right selection buttons you can select the fields
in the lines. In the first "HoTT" field you have the following selection
possibilities:
HoTT- the integrated HoTT module will be used for the signal trans-
mission.
The following settings (EXT. and SP.) are included for eventual exter-
nal RF modules of other manufacturers and they do not work with
HoTT receivers.
EXT.- the signal transmission is emitted through the DSC port to an
optional external RF module. Here is set the value PPM 10 (max. 10
control channels). The "Range test" and "Receiver outputs" func-
tions are not available. Underneath appears a new line. Here you can
set if the PPM signal has to be emitted normally or inverted.
S P. - The signal transmission will be emitted as a special digital signal
through the DATA port. The binding will be performed through the
"BIND" field. Two new lines will appear underneath. In the first line
the number of the emitted channels
(6 or 8) will be set. In the second line you can set if the signal has to
be emitted normally or inverted. The "Range test" and "Receiver
outputs" functions are not available.
If the external RF module has to be powered with the current com-
ing from the DATA port, then pay attention to what follows:
Note
The output tension of the DATA port of about 5 V must be reduced
through a stabilized step-down module to 3 / 3,3 V.
Pay attention to the switch scheme:
01
03
04
05 free
ULTIMATE
02
GRAUBELE
STARLET
BELL47G
R12
R12
R12
–––
M
M
G
M
06 free
Mod. name
Stick mode 1
n/a
Base setup model
bind
BD1
GRAUBELE
BD2
Rcv Ch Map R12 n/a
Module HoTT
Mod. name
Stick mode 1
Base setup model
SEL
GRAUBELE
PPM10
Module
EXT.PPM sig. normal
EXT.
Mod. name
Stick mode 1
Base setup model
BD
GRAUBELE
Module
SP channel 6
S P. BIND1
Mod
GND
Vcc IN = 5 V
DATA +
DATA S 125000 baud signal
Vcc
GND
DATA -
22µF/6.3 V 22µF/6.3 V
Vcc OUT = 3 ... 3.3 V
Low Drop
Voltage
Regulator SP.-MODULE
with
digital input signal