GRAUPNER S1024 User manual

Help
mz-32 / mz-16 HoTT
Reference Manual
2.4 GHz transmitter
P/N. S1024, S1024.77, S1047, S1047.US

Graupner mz-32 / mz-16 Help Reference Manual
Page 2 of 51 Help-Ref-EN-V2.7
TABLE OF CONTENTS
MAIN SCREEN WIDGETS..........................................................................................5
MODEL IMAGE WIDGET ........................................................................................5
CUSTOM STARTUP SCREEN ...................................................................................7
BASE Menu ............................................................................................................8
MODEL LIST ........................................................................................................8
MODEL LIST DETAIL.............................................................................................9
NEW MODEL........................................................................................................9
MODEL TYPE ..................................................................................................... 10
RF SET ............................................................................................................. 13
BINDING........................................................................................................... 13
SERVO SET ....................................................................................................... 16
SERVO SET DETAIL ............................................................................................ 16
CONTROL SET ................................................................................................... 17
CONTROL SET DETAIL ........................................................................................ 17
TRIM SET.......................................................................................................... 18
THROTTLE CUT .................................................................................................. 18
DUAL RATE EXPO ............................................................................................... 19
DUAL RATE EXPO DETAIL.................................................................................... 19
SWITCH SET ..................................................................................................... 20
TIMERS SET ...................................................................................................... 20
TIMERS SET DETAILS ......................................................................................... 21
TIMER SET LAP DETAILS ..................................................................................... 21
FAIL SAFE ......................................................................................................... 22
OUTPUT SWAP................................................................................................... 22
SERVO VIEW ..................................................................................................... 22
TRIM VIEW........................................................................................................ 23
TIME INFO ........................................................................................................ 23
FUNCTION Menu................................................................................................... 24
PHASE SET........................................................................................................ 24
PHASE TRIM ...................................................................................................... 24
NO DELAY CH .................................................................................................... 25
WING SET......................................................................................................... 25
WING SET DETAIL.............................................................................................. 25
WING TAIL ........................................................................................................ 26
WING TAIL DETAIL............................................................................................. 26
DIFFERENTIAL ................................................................................................... 27
AIR BRAKE ........................................................................................................ 27
AIR BRAKE DETAIL............................................................................................. 28
SNAP ROLL........................................................................................................ 28
SNAP ROLL DETAIL ............................................................................................ 28
THROTTLE CURVE .............................................................................................. 29
PITCH CURVE .................................................................................................... 29

Graupner mz-32 / mz-16 Help Reference Manual
Page 3 of 51 Help-Ref-EN-V2.7
SWASH MIXER................................................................................................... 30
SWASH OPTION ................................................................................................. 30
HELI MIXER....................................................................................................... 30
HELI MIXER DETAIL ........................................................................................... 31
FREE MIXERS .................................................................................................... 31
FREE MIXERS DETAIL ......................................................................................... 32
CROSS MIXERS ................................................................................................. 33
DIRECT ADJUST................................................................................................. 33
RING LIMITER ................................................................................................... 34
RING LIMITER DETAIL ........................................................................................ 34
MIX ONLY CHANNEL ........................................................................................... 35
CHANNEL SEQUENCER........................................................................................ 35
SPECIAL Menu...................................................................................................... 36
TELEMETRY ....................................................................................................... 36
RF STATUS VIEW ............................................................................................... 36
SETTINGS AND DATA VIEW................................................................................. 37
SYSTEM NOTICE ................................................................................................ 37
USER NOTICE .................................................................................................... 38
SENSOR NOTICE................................................................................................ 38
CONTROL NOTICE .............................................................................................. 39
VOICE NOTICE................................................................................................... 40
CONTROL SWITCH ............................................................................................. 40
LOGICAL SWITCH .............................................................................................. 41
COMBI SWITCH ................................................................................................. 41
DIGITAL SWITCH ............................................................................................... 42
SENSOR SWITCH ............................................................................................... 42
VARIO TONE ..................................................................................................... 43
TRAINER ........................................................................................................... 44
TRAINER CHANNELS........................................................................................... 44
MP3.................................................................................................................. 45
SYSTEM Menu ...................................................................................................... 45
SYSTEM SET...................................................................................................... 45
DISPLAY SET ..................................................................................................... 46
SOUND SET....................................................................................................... 46
I/O SET ............................................................................................................ 47
STICK SET ........................................................................................................ 48
FILE MANAGER .................................................................................................. 48
USB ................................................................................................................. 48
WLAN & GPS ..................................................................................................... 49
BT & COM Port................................................................................................... 49
INFO & UPDATE ................................................................................................. 50
DISCLAIMER ........................................................................................................ 51
CONTACT............................................................................................................. 51

Graupner mz-32 / mz-16 Help Reference Manual
Page 4 of 51 Help-Ref-EN-V2.7
REVISIONS
Document V2.7 – Firmware V2.004
•Changed – RF Set / Added Multi Receiver Telemetry
•Changed – Free Mixers / Added Copying a Mixer
•Changed – Model Link Widget / Added new sizes
Document V2.5 – Firmware V1.038 and V1.043
•Changed – Widget Menu / Model Link Image and Startup Image
•Changed - System Notice – Control Position
•Changed – System Sound Control – New sound control options
•Changed – BT & COM-Port – Bluetooth Call Function
Document V2.0 – Firmware 1.0.31
•Changed – Document is now generic
Document V1.1 – Firmware 1.0.29
•Added – Direct Adjust Function
•Added – Sensor Switch Function
•Changed – System Set
Document V1.0 – Firmware 1.019
•Initial Release

Graupner mz-32 / mz-16 Help Reference Manual
Page 5 of 51 Help-Ref-EN-V2.7
MAI N SCREEN WI DGETS
Your radio home screen is designed around Widgets.
There are a total of 6 decks that can be designed with
widgets. Each widget fits inside a 1, 2, or 4
presentation block. Navigation between the decks is
done by using the arrow keys (2 upper keys left of
screen) or you can assign your own navigation keys
in the System menu.
You can delete all Widgets or clear the Widget Data
for each deck by pressing the reset icon. (Circle with
an arrow next to Help icon in the upper right corner of
the screen).
You can restore the default decks by selecting
System, then System Set, and tapping on the field of Model Preset – Widget.
A deck can be global for all models or specific to a model.
You can have a different set of decks for each of your models.
To access the Widget editor, touch and briefly hold on the field you would like to place a
Widget. The Widget editor will open with available widgets to choose from.
In case you placed a Widget at the wrong place or want to change it, touch and briefly hold
on the Widget to change or delete it.
Telemetry Widgets are active Widgets that receive real-time information from the radio
system.
For example, if your receiver voltage drops below a certain value the Widget will change its
color and alert you with a voice notification.
When you touch and hold on the widget a dialog open showing how many warnings were
issued, what the current voltage is as well as the minimal and maximal voltage recorded.
This works the same for all telemetry widgets.
Taping the clear field resets all data values but timer values are not cleared if the timer
“Power on Init”is set in the timer menu.
MODEL IMAGE WI DGET
The Model Link widget provides a shortcut on a deck
for quick loading of a model therefore bypassing the
Model List menu. A Model Link widget is displayed
either as text (default) or as an image. To have a model
link widget display as an image, the following image
specifications must be in the images folder on the radio
SD card:
Windows BMP format 158x106 pixels, 24-bit, 72 dpi.
Windows BMP format 158x52 pixels, 24-bit, 72 dpi.
Windows BMP format 480x214 pixels, 24-bit, 72 dpi.
To associate an image with a model it must have the
same name as your model without the prefix.
For example:
Model name: Ab5HottRigger.mdl
Image Name: HottRigger.bmp – Image Size 158x106
Image Name: 2X1_HottRigger.bmp – Image Size 158x52
Image Name: 6X4_HottRigger.bmp – Image Size 480x214

Graupner mz-32 / mz-16 Help Reference Manual
Page 6 of 51 Help-Ref-EN-V2.7
If the image does not meet above set requirements it will not be loaded and replaced by a
default image.
How to assign an image to a model:
Load the model you would like to associate with a
widget and have an image place holder available of 2
x 2 blocks. Tap on the upper left corner to add a new
widget.
Scroll down to the Model Link widget and tap on it.
Look for your model on the model list and tap on your
model name. It should already be selected and
highlighted.

Graupner mz-32 / mz-16 Help Reference Manual
Page 7 of 51 Help-Ref-EN-V2.7
Confirm the selection by tapping on the select button.
Your model will now show on the deck with its associated image. Tapping on the model
image will reload the model.
Up to six model links with images can be displayed on
each deck.
Tapping on a model image will load the model.
This is an effective way to create a screen with all your
favorite models accessible with a single tap.
CUSTOM STARTUP SCREEN
During radio power up an image of the active model can be shown. If no image is present
then the default model type image is shown with the loaded model name at the bottom.

Graupner mz-32 / mz-16 Help Reference Manual
Page 8 of 51 Help-Ref-EN-V2.7
The image type is Windows BMP and must have the
following format:
480 x 272 pixels, 24bit at 72dpi.
To associate an image with your model the image must
have the same name as your model with the “S_”
prefix.
For example:
Model name: Ab5HottRigger.mdl
Image Name: S_HottRigger.bmp
The image needs to be copied into the Image folder on your radio using the Mass Storage
mode (System/USB Menu).
If the image does not meet above set requirements it will not be loaded and replaced by a
default model type image.
W01S1
BAS E Me n u
MODEL LI S T
In the Model List menu, you can create a new model or
select and load an existing one.
To create a new model, tap on the number next to the
model name. A selection toolbar will show with the
available options.
Tap the + icon to create a new model.
Tap on the copy icon to copy an existing model.
After tapping the + icon, a keypad will show where you
can enter your model name. Tapping the return key
brings you to the New Model selection menu.
To change the view selection of available model types,
tap on the model type icon in the upper center of the screen to activate the desired filter.
You can sort the model list by name, creation date or bind group by tapping on the table
header.
B01S1

Graupner mz-32 / mz-16 Help Reference Manual
Page 9 of 51 Help-Ref-EN-V2.7
MODEL LI S T DETAI L
By tapping on the model Name, additional details about
the selected model are displayed prior to loading and
activating the model.
The Date and Time fields show when the model was
created, and the Model Time shows how long the model
has been actively used.
The Bind Group field shows to which group this model
belongs (check the RF Set menu for additional
information).
The Bind Info fields show how many receivers the
selected model is bound to and how many channels
each bound receiver has.
The bottom fields show the model configurations such as model type, wing type and tail
type. To load and activate the model, tap the Select field.
B01S2
NEW MODEL
The New Model menu can only be accessed from the
Model List menu when creating a new model.
Tap on the Model Type icon to select your model type.
Each model type will have different selection options.
The following example is for airplanes.
Tap on the Wing Type icon to select your airplane’s
wing type. If your wing type is delta tap on the delta
icon symbol to change the wing type selection.
Tap on the Tail Type icon to choose your tail type.
Tap on the engine type to select how many engines
your airplane has.
Tap on Throttle Minimum to change the throttle direction.
A selection of None (only available for Airplanes) is for models without a motor, such as a
sailplane. A selection of Rear causes the throttle channel to increase as the throttle control
is increased. A selection of Front causes the throttle channel to decrease as the throttle
control is increased.
Tap on the stick mode to change your stick mode configuration.
When done tap on the Create & Apply button, which will create the model and reinitialize
the radio to load the new model.
You can make later changes to the model configuration from the Model Type menu.
B01S3

Graupner mz-32 / mz-16 Help Reference Manual
Page 10 of 51 Help-Ref-EN-V2.7
MODEL TYP E
In the Model Type menu, you can change the existing
model configuration or rename the model.
Rename Model
Tap on the model name to bring up the keypad where
you can enter your new model name. When finished,
tap on return key which brings you back to the model
type selection menu.
Change Model Type
Tap on the Model Type icon to select your model type.
Each model type will have different selection options.
Airplanes
Tap on the Wing Type icon to select your airplane’s wing type. You can set your airplane
wing type with the following configurations:
•1 Aileron
•1 Aileron – 1 Flap
•2 Ailerons
•2 Ailerons – 1 Flap
•2 Ailerons – 2 Flaps
•2 Ailerons – 4 Flaps
•4 Ailerons – 2 Flaps
•4 Ailerons – 4 Flaps
If your wing type is delta tap on the delta icon symbol to change the wing type selection.
•2 Ailerons
•2 Ailerons – 1 Flap
•2 Ailerons – 2 Flaps
•2 Ailerons – 4 Flaps
•4 Ailerons – 2 Flaps
•4 Ailerons – 2 Flaps

Graupner mz-32 / mz-16 Help Reference Manual
Page 11 of 51 Help-Ref-EN-V2.7
Tap on the Tail Type icon to choose your tail type. You can select from the following tail
types:
•Normal
•V-Tail
•2 Elevator
Tap on Throttle Minimum to change the throttle
direction.
A selection of None (only available for Airplanes) is for
models without a motor, such as a sailplane.
A selection of Rear causes the throttle channel to
increase as the throttle control is increased.
A selection of Front causes the throttle channel to
decrease as the throttle control is increased.
Tap on Engine to select how many engines your
airplane has.
You can select 1 – 4 engines on your model.
Brake Function controls the switching point for the
brake control. Tap on the input field (default throttle)
to select the control for the brake channel.
To set the offset value for brake activation, move the
control to the desired position and tap the offset field
to store the value.

Graupner mz-32 / mz-16 Help Reference Manual
Page 12 of 51 Help-Ref-EN-V2.7
Helicopters
Tap on Swash Type to select the number of swash plate servos and their geometry.
You can select from:
•1 Servo (for flybarless controllers)
•2 Servos
•3 Servos (2 roll)
•3 Servos (140 degrees)
•3 Servos (2 Nick/Elevator)
•4 Servos (90 degrees)
Set your desired throttle direction.
Tap on Linear Swash to set whether to compensate for
the arc of the servos when changing collective pitch.
Set the value to Linear to enable the compensation or
Normal to disable it.
Tap on Thro. Limit to enable (Limit) or disable
(Unlimit) the channel 12 throttle limiter.
Selecting Unlimit will also free up channel 12 for other
functions.
When finished tap on the Model Types icon to exit the
menu.
B02S1

Graupner mz-32 / mz-16 Help Reference Manual
Page 13 of 51 Help-Ref-EN-V2.7
RF SET
In the RF Set menu you will manage all RF and
Telemetry communications between the radio and
receiver as well as binding your model to the radio.
BI NDI NG
Depending on your radio model you can bind up to 4
receivers to your model. The binding process requires
you to place the receiver in bind mode, which can be
done by pressing the SET button on the receiver. After
2-3 seconds, you can tap the bind button on the radio.
You need to bind RX1 first. When binding has been
successful the Rx column will show the channel count
of the receiver and below in small letters the current receiver firmware version. For
example, a GR-24 will show as R12 and a GR-12L will show as R6.
Depending on the receiver model you may need to follow a slightly different procedure to
successfully bind the receiver to the radio.
Bind Method A:
Press the SET button and keep it pressed for 2-3 seconds and press the bind button on the
radio.
GR-12/GR-18/GR-24 PRO/GR-16(L)/GR-24(L)/GR-32(L):
Green LED on – Receiver bound
GR-12L:
Red LED off – Receiver bound
Bind Method B:
Receiver goes automatically into binding mode (Flight Controllers after 15 seconds with
blinking red LED)
GR-10C/GR-12SC & SH/Falcon 12/Falcon 12 PLUS/Alpha 110/S1038, S1039
Red LED off – Receiver bound
Notes:
If binding was not successful, repeat the bind procedure.
Make sure that the receiver is at least 50cm/2ft away from the radio.
Verify that the power source is sufficient to power the receiver.
Make sure that the power polarity is properly connected. The GR-12 6 channel
receivers require that the negative wire is facing up.
Verify that the bind SET button is properly pressed.
RX
Tap on the selected blue Rx field (a receiver must be bound) and a dialog will show with
the available channels and channel numbers for that receiver. Here you can remap the
channels or assign a digital switch output by tapping on the icon next to the channel
number.
Tap on the channel you want to remap and use the arrow keys to map the channel to
another channel.
Tapping on the Reset button will restore all channels to default.
T.Sel (Telemetry Select)
Tap on the receiver which you want to designate as the active telemetry receiver. There
can be only one telemetry receiver active at any time.
Modulation
The default modulation is set for HoTT (Hopping Telemetry Transmission)

Graupner mz-32 / mz-16 Help Reference Manual
Page 14 of 51 Help-Ref-EN-V2.7
RF Transmit
Default is set to off. Tapping the off field will turn the RF to on. If no receiver is found the
radio will sound an error and the Graupner front logo will blink in blue.
Auto RF On
Setting this field to on will activate the RF immediately after the model is loaded bypassing
the RF On/Off dialog shown on startup when the Auto RF is switched to Off.
Bind Group
For an unbound model memory, the default is the next free binding group. However, as
long as the model memory is unbound, this specification can be changed by tapping the
icon on the “Bind Group” field. You can select from the following options:
„Global“ enables the receiver to respond to the transmitter signal on a non-exclusive basis.
What this means is that any other receiver that is bounds as global will respond to the
transmitter signal of another model memory that was also bound as global. This can be
used in situations where for example you have multiple models that are all the same and
do not need different model memory settings.
„Group“ enables the receiver to respond exclusively to the group ID assigned during
binding. For example, if you bind a receiver to bind group A0, that receiver will not respond
to a signal from the transmitter of a model memory that was bound global or, for example,
as group C2.
You can bind another model memory also under bind group C2, which will result in one
model memory sharing two receivers under a single bind. When both receivers are turned
on, they will respond simultaneously to the same control inputs of the transmitter.
The use case for this is, for example, during competition when one airplane becomes
inoperative and you would like to continue the contest using an identical airplane without
switching model memories on your transmitter to avoid losing time. All you need to do is
power the other airplane and wait for the receiver to establish the bind.
Range Test
When the range test starts, the output of the transmitter decreases significantly. A practical
functional test can therefore be performed at a distance of less than 100 m. After the end
of the range test, the transmitter switches back to full output power and the range test
signal tone stops.
Range test step-by-step
Verify that the receiver and transmitter are communicating properly and that all control
surfaces are functional.
Place the model on a flat surface (cement, mowed lawn or ground) with the receiver
antenna at least 15 cm above ground.
Hold the transmitter at hip level at a slight distance from your body.
Start the range test in the „RF Set“ menu by tapping the icon in the “Range Test” field.
The time display begins to count down and a beep will sound throughout the entire range
test.
Move away from the model within the given 99 seconds range test and move the control
sticks while maintaining visual contact.
If you notice an interruption in the connection at any time within a distance of about 50 m
/ 160 ft, try to reproduce it.
If possible, switch on an existing motor, to additionally check the interference resistance.
Carry out the extended range test before starting up your model, simulating all the control
movements occurring in practice. To guarantee a safe model operation, the range must
always be at least 50 m / 160 ft on the ground.

Graupner mz-32 / mz-16 Help Reference Manual
Page 15 of 51 Help-Ref-EN-V2.7
Telemetry Speed
In those situations where, for example, two airplane models are about to be operated at
close proximity to another controlled by two separate transmitters, you may choose to
reduce or eliminate the telemetry back channel of one of the models to avoid potential
interference. Situations that may need to be evaluated include drones that have a separate
transmitter for control and camera operations, or airplanes that tow or carry other
airplanes, can be all pick up interference from the telemetry downlink transmission.
Experiment with the proper telemetry period value for your situation.
You can reduce the amount of telemetry data transmitted back from the receiver to the
radio as follows:
100 % - Transmits telemetry data with each data packet.
50% - Transmits telemetry data each 40ms
33% - Transmits telemetry data each 80ms
Multi Receiver Telemetry
Models with multiple receivers can now be accessed individually during flight to receive
telemetry readout of each receiver (mz-16 max 2 RX’s, mz-32 4 RX’s).
The following needs to be observed when using this advanced feature.
Receivers must have identical telemetry modules installed. For example, if one receiver has
telemetry installed and you would like to get ESC telemetry readings on another receiver,
that receiver has to have an identical telemetry ESC. This does not apply when only receiver
voltage, RSSI, and temperature need to be monitored as all Graupner receivers have this
capability built in.
The first active receiver after powering the radio on will be used for scanning.
Receivers that need to be part of the scan need to have their “T.Sel” set in the RF Menu.
Receiver switching is only active if one of the widget screens is active or from the Settings
and Data View Telemetry Menu.
Switching between receivers is done on channel CH16.
•CH16 = -100% = Receiver 1 / mz-16/32
•CH16 = 0% = Receiver 2 / mz-16/32
•CH16 = 100% = Receiver 3 / mz-32 only
•CH16 = 125% = Receiver 4 / mz-32 only
NOTE: Switching between receivers does not affect your control channels. Only the
telemetry values are being read and announced when CH16 is being cycled.
NOTE: You will need the most current receiver software installed
NOTE: You can automate the switching between receivers by using a digital switch blink
type.
B03S1

Graupner mz-32 / mz-16 Help Reference Manual
Page 16 of 51 Help-Ref-EN-V2.7
SERVO SET
In the Servo Set menu you can make all basic
adjustments to your servos to optimally tune them to
your model.
The first two columns show the channel number and
channel name. Tapping on the channel number or
name shows the edit bar where you can name or
rename your channel name. Choose a proper channel
name that will help you identify each channel function.
The Direction field enables you to reverse the channel
direction.
Tapping on the Detail icon lets you fine tune servo
parameters.
The Trim field is your sub trim value for centering your servo or control surfaces.
The Travel and Limit fields let you adjust servo throws and maximal servo deflection. Set
the deflection to a value where the servo does not mechanically bind.
The value in the Delay fields will determine the speed of the control movement.
All settings in the Servo Set menu are applied globally and are not Phase dependent.
NOTE
Please be careful when making changes to the throttle direction as it may unexpectedly
start the motor. Always ensure that the propeller or main battery are disconnected.
B04S1
SERVO SET DETAI L
The Servo Set Detail menu enables you to fine tune
your servo settings.
Balance: Here you can adjust the servo travel to
ensure that each control surface is moving in an
identical way. To make changes to a curve point, move
the control over the point to select or by tapping on the
input field under the balance column.
When a curve point is selected, it will turn orange. Now
you can either move the curve point using the arrow
keys or with the orange slider tab along the vertical
axis.
Trim: your sub trim for centering your servo or control surfaces.
Travel: sets the desired travel range for your servo.
Limit: sets the maximal servo deflection to a value where the servo does not mechanically
bind.
B04S2

Graupner mz-32 / mz-16 Help Reference Manual
Page 17 of 51 Help-Ref-EN-V2.7
CONTROL SET
In the Control Set menu, you can set the controls such
as switches, sliders and buttons that will activate and
operate each channel. When setting up your model, the
system automatically assigns controls depending on
your model setup. It is not recommended changing
these pre-set controls.
Scrolling the control set menu down (swipe the screen
up or down) will show the first 16 available channels.
To view channels 17 – 32 tap on the page icon next to
the question mark.
To change the channel name, tap on the channel
number or channel name which reveals the edit bar.
A control for a channel can be set globally or phase dependent allowing you to change the
control used depending on the flight phase.
To assign a control to a channel, tap on the channel control field. Moving a control will
automatically record that control as the main control. You can have different input control
types assigned to each channel.
Additional control types can be created in the special menu.
The values in the delay fields will determine the speed of the control movement.
Tapping on the detail icon provides access to different curve types to fine tune your channel
behavior.
B06S1
CONTROL SET DETAI L
The Control Set detail menu provides various curve
types that can influence servo travel as well as channel
offsets.
The basic menu displays the active channel and
whether the channel is global or phase dependent. The
overlay channel field provides access to a field selection
menu where you can pick another channel to overlay
the existing channel. If the channel curves are
different, a brown graph line will show the differences
between each channel. This can be helpful when trying
to create identical curves between multiple channels.
In the other menu, you can select the curve type
(linear, flat and multi point). Tap on the curve type icon to change the curve type. You can
select the spline type by tapping on the spline icon.
In the value menu you can set the curve (travel) behavior of the channel.
Depending on the curve type selected you can move the curve over the Y axis or X axis
and change each curve point or offset.
To change a curve point, move the control to select the point so that it becomes active.
You can make changes by tapping on the X and Y fields arrow keys or you can slide the
colored tabs along the X and Y axes.
Adding or removing curve points can be done by moving the control over the curve point
and, when highlighted, tapping the minus key for delete, or by positioning the control cursor
over a point along the curve and tapping the plus key for adding a point.
B06S2

Graupner mz-32 / mz-16 Help Reference Manual
Page 18 of 51 Help-Ref-EN-V2.7
TRI M S ET
In the Trim Set menu, you can set the trim behavior
for each of your trims, giving you the most optimal
configuration for your trim settings.
You can have up to 8 different trims for each of your
flight controls. To add a new trim, tap on a number in
the number column to bring up the selection toolbar
and tap the + icon. You will need to select a channel
for which you would like to set up the trim.
To add a control, tap on the Ctrl field to select the
control type you will be using for that channel.
Tapping the Function name permits the re assignment
of the current line settings to a different control function (channel).
The Group icon will set the trim as global or phase dependent.
The Value field shows the current value of the trim position for that channel.
Tapping on the Store field will copy the current trim setting to memory and reset the trim
value back to zero. This enables you to try different trim settings and view the differences
between the stored and current trim settings.
You can select from five different trim types depending on your needs and situation.
Linear decrease of trim impact on both sides of the neutral position.
Even change of trim impact over control range.
Linear decrease of trim impact towards neutral position on lower part of the control
range.
Linear decrease of trim impact over entire control range.
Inverted linear decrease of trim impact over entire range.
The Travel field value determines the maximum trim travel.
B07S1
THROTTLE CUT
The Throttle Cut menu provides an easy way to control
your throttle on/off position.
The Control field determines which control is going to
be used for the throttle cut.
The Cut Off value determines at which position the
throttle cut will occur. For example, on gas motors you
would like to have your idle position at -100 but your
cutoff at -130.
The Trigger value determines the threshold position
when the throttle cut is engaged.
The Action field shows the active state of the throttle
cut.
B08S1

Graupner mz-32 / mz-16 Help Reference Manual
Page 19 of 51 Help-Ref-EN-V2.7
DUAL RATE EXP O
The D/R Expo menu enables you to set up control rates
and exponential rates for each control surface. You can
have up to 8 different control rates where each has four
different state values.
To add another rate, tap on a number in the number
column to bring up the selection toolbar and tap the +
icon. You will need to select a channel for which you
would like to set up rates. Tapping the Function name
permits the re assignment of the current line settings
to a different control function (channel).
The Group column will set the rate as global or phase
dependent.
In the rate and expo column, you can set the minimum and maximum deflection rates and
exponential values.
Tap on the detail icon to access the detail settings for this menu.
B09S1
DUAL RATE EXP O DETAI L
In the Dual Rate Detail menu, you can assign the rates
and switches that will operate your dual, triple or quad
rates.
The detail menu has three sub menu settings.
BASIC
Edit Ch. – Shows the current active channel.
Overlay Ch. – Provides access to a secondary channel
you can lay over the current channel to compare
channel curve settings.
Curve Type – Tapping on the curve icon changes the
active curve type.
Group – Tapping on the group icon changes the current function from global or phase
dependent.
VALUE
Rate – Tapping on the value fields displays the control toolbar on the bottom. Use the link
icon to synchronize the value fields. Changing the values is done with the keys. Use the
reset icon to reset values back to their default.
Expo - Tap on the expo value field to set the amount of desired expo. Note that, depending
on the selected curve type, you can have a single or dual expo setting.
QR/EX - You can assign up to four rates for each control surface. Tap on the field number
which is associated with the assigned control number to edit the rates.
QR/EX
To assign a control to activate a rate, tap on the control field. The select control input dialog
will appear, where you can select the control you would like to use.
B09S2

Graupner mz-32 / mz-16 Help Reference Manual
Page 20 of 51 Help-Ref-EN-V2.7
SWITCH SET
In the Switch Set menu, you can set the switching
point for controls, sliders and switches that can be used
for activating mixes and controls when a logic control
is used. It also allows you to set the trim steps and
speed for the digital trims that are used with control
surfaces such as ailerons and elevator.
Each trim and control can be independently set. To
view the detail menu, tap on the DT, ST, LV or DV
control.
In the configuration dialog tap on the control you would
like to make changes for to bring up the switch detail
menu.
You can set the following parameters.
Switching Position – The default is set at 75% for each
travel direction. This indicates that when the control is
moved past the +75% or -75% position, a trigger
event will happen that can be used with a logical
switch. Lowering the values will cause the trigger point
to be closer to the center point of the control.
Digital Trim – The default values will determine how
many steps a digital trim control will have and how fast
it will travel. Setting the steps to zero will disable the
digital trim travel.
The switch set menu has additional pages that can be accessed with the arrow keys (top 2
keys left of screen) or by swiping the screen.
The secondary screen shows the current position of the digital trims (DT), knobs (DV),
levers (LV) and switches (SW). Moving each control or switch will animate the control on
the screen while tapping on the control will open the configuration dialog.
The additional screens on the switch set menu are for future development.
B13S1
TIMERS SET
Depending on your radio model you can create up to 6
timers for time or lap recording. Timers can be either
global or phase dependent.
Adding a new timer is done by tapping on the + sign
or on the number of an existing entry to bring up the
selection toolbar.
When tapping on the + sign, the timer type dialog
appears where you can select the type of timer, lap or
start/stop timer.
When the selection toolbar is active, you can perform
delete, re-order or rename functions.
The group column shows if the timer is global or phase dependent. To change group status,
tap on the group icon.
You can change the timer type by tapping on the type column.
The Act icon indicates if the timer is active or disabled.
Tapping on the Detail icon opens the timer set detail menu.
B10S1