GRAUPNER JODEL ROBIN DR 400/180 User manual

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY
We reserve the right to introduce modifications. Not liable for printing errors!
11/2011
1
Re: Order No.9585
9585.M
Instructions
JODEL ROBIN DR 400/180
For internal combustion motors up to 40 cm³
and
Electric motors
Requires a HoTT radio control system with 5 functions

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY
We reserve the right to introduce modifications. Not liable for printing errors!
11/2011
2
Specification
Wingspan about 2200 mm
Fuselage length without spinner about 1640 mm
wing area about 84 dm²
Tailplane area about 18.4 dm²
Wing area about 102.4 dm²
All-up weight depending on equipment about 9000 g
EWD 0-0.5 degrees
Centre of gravity about 130-140 mm behind the leading
edge
Caution: This model is not a toy!
If you do not have experience with such motorised models, please ask experienced
model flyers for help. If the model is operated without the proper knowledge, injuries
can result. Think of your health and safety!
Important! Before you start the assembly!
Even if you have already built lots of RC models, read these instructions through
carefully and check the parts in the kit for completeness. A lot of effort was made to
keep things as simple as possible without neglecting safety.
Note on the covering sheet
Because of strong changes in the weather (temperature, humidity, et cetera), folds
can appear in the covering sheet. In rare cases, the components can even be
warped. This lies in the nature of wood construction with covering sheet. This can be
corrected as follows using a hair dryer like those available to model builders.
Creases: Blow with hot air and rub with a soft cloth.
Warped area: Gently twist the area against the direction of warping and smooth it
out again using hot air.
Caution! Never use more heat than is absolutely necessary. If the iron is too hot, the
covering sheet will melt and holes will form.
The extensively pre-fabricated model can be built in a very short time. However, the
remaining steps are important and have to be carried out with care. Doing this work
properly determines whether the model will have the prescribed rigidity and flight
characteristics; so please work slowly and precisely!
When putting screws into wood, apply a little casein glue to keep them from
loosening: Squirt casein glue into the drill hole and screw in the screw.
Tips on building the model
•Before assembling the model, it is essential to read the construction diagram and
the instructions all the way through. When using tools, be aware of the possible
dangers.

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY
We reserve the right to introduce modifications. Not liable for printing errors!
11/2011
3
•Use only suitable cables that are adequate for the electrical currents that occur
during operation.
•Set up the receiver aerial as far as possible away from the cables carrying the
operating current (at least 3 cm).
•Clean residual grease from all connections that are to be glued. This could be
done, for example, through sanding and using a non-relubricating cleaning
solution. The same goes for the surfaces to be painted, in order to make sure that
the paint sticks. Before gluing parts, always roughen the corresponding surfaces
(especially for GFR fuselages) carefully with fine sandpaper and de-grease them
thoroughly, for example with acetone. Otherwise, adequate adhesion is not
assured.
Other required accessories
Internal combustion motor and accessories
Recommendations for internal combustion motor
Motor
Order No. Capacity cm³ Silencer Order No. Propeller Order No.
OS MAX FS 200 S
2728
32.4
2728.33
Motor accessory
(included)
1318.45.25
Petrol motor
GT 33
2772
33
2772.33
45x25 cm
1314.18x10“
Recommendations for electric motor
Electric
motor
Order No.
Propeller
Order No. Drive battery Order No. Speed controller
Order No.
COMPACT
740 Z
7780
45 x 25 cm
1326.22x10 LiPo 5/5200 11.1V/5.2Ah
9752.5
COMPACT
CONTROL
90S
7228
Radio control system
It must have at least 5 control functions and 10 servos. Furthermore, the transmitter
must be capable of servo rotation reversal.
Particularly recommended: Computer System MC-22s to MC-24. Servos with
standard dimensions can be installed.
As receiver battery, we recommend: two GRAUPNER 5N-5000 NiMH Order No.
98903.5, which must always be serviced well before and after flight operations,
meaning that the battery has to be charged and discharged again multiple times until
the specified capacity has been reached.

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY
We reserve the right to introduce modifications. Not liable for printing errors!
11/2011
4
Connecting the two ailerons and the landing flap servos to the receiver requires four
spark suppression filters, Order No. 1040 or one collapsible ferrite core, Order No.
98516.1 with four extension cables Order No. 3935.18.
The two aileron servo cables must each be extended with an extension cable Order
No. 935.75, the two landing flap servo cables with Order No. 3935.32, the two
elevator servos with Order No. 3935.105, the throttle servo with Order No. 3935.18,
the nose gear servo with Order No. 3935.11, the aero-tow coupling servo with Order
No. 3935.32. Two Order No. 7907.2 are used as servo control arms.
Receiver and battery: Store in foam material.
Any servo of standard size and an adjusting power of about 50 Ncm can be installed.
Adhesives
Epoxy glue, such as "UHU plus schnellfest," Order No. 962
Epoxy glue, such as "UHU plus endfest 300," Order No. 950.43
"UHU Holzleim express" casein glue, Order No. 958.60
"UHU hart" glue, Order No. 534.35
Fast-setting (cyano-acrylate) glue, such as Order No. 5821
Fast-setting (cyano-acrylate) glue, such as Order No. 5822
Thread lock fluid, such as Order No. 952
Accessories for operation (not included)
Fuel, depending on the motor petrol/oil mixture (see instructions for the motor used)
Fuel tubing, petrol, such as Order No. 1325.2
Manual fuel pump, such as Order No. 6870
Ignition battery, Order No. 8716.5
Charger cables and chargers for electric aircraft
Required tools (not included)
Various (Phillips) screwdrivers, needle-nose pliers, flat-nose pliers, wire cutter, balsa
knife or razor blade, various drills, pencil, felt marker, soldering iron with fine tip.
Heat-shrink tubing, Order No. 3391.8
Assembling the JODEL ROBIN DR 400/180
Wings with undercarriage and tailplane

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY
We reserve the right to introduce modifications. Not liable for printing errors!
11/2011
5
Do not begin the assembly until you have familiarised yourself with the components
and the individual construction stages. If you are not satisfied with any component,
report it to your retailer before you start the construction process.
Using sandpaper or sanding block, sand the control horns on the surfaces to be
glued in order to achieve an adequate connection when gluing.
As seen in the photos, unstick the slots for the GRP control horns, put a dab of glue
into the slot, and push the control horn in until it stops.
Wipe off any excess glue.
Until the glue hardens, the servos are installed in the corresponding mounts and
fastened into the wing or tailplane.
Extend the servo cables using the corresponding extension cable and make sure
they can not come loose, for example with a piece of heat-shrink tubing or a drop of
fast-setting glue. Using the RC system, bring the servos in the middle position and
install the servo levers.

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY
We reserve the right to introduce modifications. Not liable for printing errors!
11/2011
6
Fasten the servo to the attachment block using the screws included with the servos.
To do so, insert the rubber grommets with the brass hollow rivets, collar downward,
into the servo flange. For drilling Ø 1.5 mm holes for the screws, the hollow rivets can
be used as a drilling template. To make it easier to push them in,
the hollow rivets can be placed onto a screwdriver of the proper size.
Now the servo cables are pulled into the wing halves and tailplane halves using a
thin string. Just behind the connector, tie the string to the cable and pull it in so that it
comes out the wing root.
With servo and rudder in neutral position, screw together the lengths of the rods for
the ailerons, landing flaps, and elevators, adjust them, and use thread lock fluid (such
as UHU schraubensicher) and lock nuts to secure them against loosening.

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY
We reserve the right to introduce modifications. Not liable for printing errors!
11/2011
7
As shown in the photo, secure the hinges for the landing flaps using heat-shrink
tubing.
On the underside of the wings, there are markings indicating where the flap hinges
can be screwed in. Make sure that the axes of rotation of the hinges are all the same
distance from the trailing edge of the wing.
As shown in the photo at the left, a screw is used to
fix the hinges in place; then use an engineer's square or geometric protractor for
alignment with the trailing edge, and fasten the hinges with two more screws. Now
push the landing flaps up against the wings and tape them in place temporarily; align
them, and fasten them with screws.
Screw the pushrods together as shown in the following photos.

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY
We reserve the right to introduce modifications. Not liable for printing errors!
11/2011
8
In the next step, use your fingers to feel for the slot for the landing gear wire, and
melt it free with a hot soldering iron.
Now place the leg of the undercarriage into the slot, to mark the attachment points of
the two tabs and the wheel fairing support block.
Drill pilot-holes in the wings for the retaining screws; then screw the tabs and the
wheel fairing support block to the wing.

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY
We reserve the right to introduce modifications. Not liable for printing errors!
11/2011
9
For the wire undercarriage units you will need to file away the inside of the two
fairings a bit. When installing the fairings, make sure that the wheel covers face
outwards. The wheels can now be attached to the axles using collets and grub
screws. Apply UHU thread-lock fluid to the grub screws to prevent them working
loose. Loosen the grub screw at the front of the shock absorbing strut, loosen, and
push the wheel axle to the other side. Re-tighten the grub screw.
The wheels and wheel fairings must be aligned exactly parallel with the fuselage
centreline.
The final stage on the wing is to install the landing searchlight.
As shown in the following photographs, fit the two LEDs in the white plastic holder
and secure them with a little UHU Power all-purpose adhesive.
Trim the outside edges of the plastic holder so that it fits in the recess in the wing.
Route the connecting leads of the two diodes to the root rib using a piece of thread,
and run them out of the drilled access hole. The plastic holder can now be glued in
using UHU Power all-purpose adhesive. Fix the glazing to the wing using clear
adhesive tape.

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY
We reserve the right to introduce modifications. Not liable for printing errors!
11/2011
10
Fuselage with tailplane, vertical stabiliser, and nose gear
The vertical stabiliser can either be glued permanently to the fuselage or fastened
removably using four screws.
Only the fastening of the vertical stabiliser using screws is described.
Before putting in the screws, the two extension cables for the two elevator servos
must be pulled into the fuselage.
Use the Ø 12 mm aluminium tube to put the horizontal stabiliser onto the fuselage to
test the fit; the two extension cables must be routed through the openings of the
horizontal stabiliser on the right and left.
The two halves of the tailplane must be attached to the fuselage using the Ø 12 mm
aluminium tube and four M3x16 Allen screws each.