Gravitech MicroResearch MR-BusIO-SSRAC User manual

MR-BusIO-SSRACTM BusIO Solid State Relay BOARD
User Manual
Copyright © 2007 MicroResearch
GRAVITECH GROUP WWW.GRAVITECH.US
GRAVITECH.US
uResearch
GRAVITECH GROUP
Downloaded from Elcodis.com electronic components distributor

MR-BusIO-SSRACTM BusIO Solid State Relay BOARD
User Manual
Copyright © 2007 MicroResearch
GRAVITECH GROUP WWW.GRAVITECH.US
The MR-BusIO-SSRAC is an experiment
board for switching AC output voltage by
using SSR (Solid State Relay). SSR is
similar to mechanical relay that consists of
inductor and surface contact. The internal
structure of SSR uses semiconductor
material to switching ON and OFF. The
maximum controlling voltage is 400VAC at
6A. It is best for switching AC output
voltage.
The board can be use with MR-BusIO-
MAIN board or stand-alone. PCB size is
0.63” x 2.80”
General structure of SSR is shown in
figure 1. Voltage applied to the input of an
SSR causes the LED to shine on the
photo-sensitive diode. The voltage is
causing the TRIAC to turn on.
FIG 1: General structure of SSR
The board consists of MOC3042 IC which
internally combined photo-coupler and
zero crossing circuit together. The
function of zero crossing circuit is to
detect the voltage at zero point and supply
current to the gate of the TRIAC. For
330ohm resistor and 0.1uF capacitor at
the gate of the TRIAC, their function is
sharing the current at the gate so they are
not too high. Also, protect external noise
into circuit.
The circuit is operating with AC voltage
only. It is start when applying logic HIGH
to an I/O pin. The indicator LED then
illuminated which mean it is now close
circuit.
User can connect AC load up to 400VAC
at 6A through output 2-PIN terminal block.
In case of interfacing with inductance load
such as motor, user should add Snubber
circuit by putting R1 47ohm 1W resistor
and C1 0.1uF 600V capacitor as shown in
Figure 1.
Description
Operation:
Downloaded from Elcodis.com electronic components distributor

MR-BusIO-SSRACTM BusIO Solid State Relay BOARD
User Manual
Copyright © 2007 MicroResearch
GRAVITECH GROUP WWW.GRAVITECH.US
The MR-BusIO-MAIN is available for
purchase via our website. If you don’t see
the item you need, please contract our
sales department at [email protected]
•MR-BusIO-MAIN
Experiment board which receives output
signals from any microcontrollers. The
signals then distribute to daughter boards
for each experiment. It designed to
connect directly with 10PIN MRconnect©.
It is a quick and easy way to control up to
8 daughter boards.
FIG 2: MR-BusIO-SSRAC Board Layout
FIG 3: MR-BusIO-SSRAC Schematic
MR-BusIO-MAIN
Downloaded from Elcodis.com electronic components distributor

MR-BusIO-SSRACTM BusIO Solid State Relay BOARD
User Manual
Copyright © 2007 MicroResearch
GRAVITECH GROUP WWW.GRAVITECH.US
We maintain a website where you can get
information on our products, obtain
literature and download support files. Visit
us online at:
WWW.GRAVITECH.US
Use our online Forum or e-mail your
technical support questions to
[email protected]. We try to respond
to your questions the same day.
For sales questions or to place and order,
direct your e-mails to [email protected].
Refer to our website for product pricing,
shipping rates, payment instructions, and
for other info we need to complete your
order.
Disclaimer: MicroResearch reserves the right to modify its products or literature, or
to discontinue any product at any time without prior notice. The customer is
responsible for determining the suitability of any device for any application
developed using MicroResearch components.
Notes
Contact Us
Downloaded from Elcodis.com electronic components distributor