GRE AR7051 Manual

IF YOU HAVE ANY PROBLEM, CONTACT US! (UK Green number)0800 91 76 778
SI TIENES ALGÚN PROBLEMA,¡CONSÚLTENOS! - EM CASO DE PROBLEMA,¡CONSULTAR-NOS! [phone]
EN CAS DE PROBLEME, NOUS CONSULTER! France Tel
Belgique numéro verde
Suisse numéro verde
Nederlands
[phone]
0800 10 211
08 /563 820
0800 022 33 04
BEI PROBLEMEN KÖNNEN SIE SICH MIT UNS UNTER DER FOLGENDEN DEUTSCHEN Deutchland
Österreich
Schweiz freie Nummer
SCHE
0180 333 0123
[phone]
0 800 /563 820
PER OGNI VOSTRA EVENTUALLE OCCORRENZA, INTERPELLATECI! Italia
Suizzera numero verde 800 781 592 0 800/563 820
MOCHT U EEN PROBLEEM HEBBEN,... ¡RAADPLEEG ONS! Nederlands
Belgie 0800 022 33 04
800 10 211
TECHNICAL CARACTERISTICS
CARACTERÍSTICAS TÉCNICAS
RENSEIGNEMENTS TECHNIQUES
DATI TECHNICI
TECHNISCHE ANGABEN
TECHNISCHE GEGEVENS
CARACTERISTICAS TECNICAS
Cod. AR7051-0005-00
- We reserve the right to change all or part of the features of the articles or contents of this document, without prior notice.
- Nos reservamos el derecho de cambiar total o parcialmente las características de nuestros artículos o contenido de este documento sin previo aviso.
- Nous nous réservons le droit de modifier totalement ou en partie les caracteristiques de nos articles ou le contenu de ce document sans préavis.
- Ci riserviamo il diritto di cambiare totalmente o parzialmente le caratteristiche tecniche dei nostri prodotti ed il contenuto di questo documento senza nessum preavviso.
- Wir behalten uns das Recht vor, die merkmale unserer Produkte und den inhalt dieser beschreibung ohne vorherige unkündigung ganz oder teilweise zu ändern.
- Wij behouden ons het recht voor geheel of gedeelteliijk de kenmerken van onze artikelen of de inhouk van deze handleiding zonder voorafgaand bericht te wijzigen.
- Reservamo-nos no direito de alterar, total ou parcialmente caracteristicas dos nossos artigos ou o conteudo deste documento sem aviso prévio.
Ø Filter / Ø Filtro / Ø Filtre / Ø Filtro / Ø Sandfilter / Ø Sandfilter / Ø Filtro Ø 380
Filtering speed / Velocidad de filtración / Vitesse de filtrage / Filtriergeschwindigkeit / Velocità filtrazione /
Filtersnelheid / Velocidade de filtragem 50 m3/m2h42 m3/m2h
Flow rate / Caudal / Débit / Durchflubmenge / Portata / Debiet / Caudal 5 m3/h 4,5 m3/h
Potency / Potencia / Puissance / Stromstärke / Potenza / Vermogen / Potência 482 W
Voltage / Voltaje / Voltage / Spannung / Voltaggio / Voltagem / Voltage 230 V 50 Hz
Sand filling / Carga de arena / Charge du sable / Sandladung / Carico di sabbia / Zandlading / Carga de areia ± 40 Kg
Grain size / Granulometría / Granulométrie / Körnung / Granulometria / Korrelgroottemeting / Granulometria 0,4 - 0,8 mm
DISTRIBUIDO POR:
MANUFACTURAS GRE. S.A.
C./ ARITZBIDEA Nª57, BARRIO TROBIKA
48100 MUNGIA (BIZKAIA) ESPAÑA
TEL. [phone] · FAX. [phone]
http://www.gre.es
Nº REG. IND.: 48-06762
FABRICADO POR : C.I.F. A-08246274
MONOBLOCS AR7051 AR7051C
SPECIFIC MANUAL
MANUAL ESPECIFICO
MANUEL SPÉCIFIQUE
SPEZIFISCHE ANLEITUNG
MANUALE SPECIFICO
SPECIFIEKE HANDLEIDING
MANUAL ESPECÍFICO
MONOBLOCK FILTER · FILTRO MONOBLOC · FILTRE MONOBLOC · FILTRO MONOBLOCCO
MONOBLOCK-FILTER · MONOBLOCK FILTER · FILTRO MONOBLOCO
www.gre.es
AR7051- AR7051C
AR7051-0005-00
850 mm
719 mm
www.PiscinasDesmontables.es
www.PiscinasDesmontables.es

MANUFACTURED BY:
METALAST, S.A.U
N.I.F.: A-08246274
MONOBLOC – FILTERMOM
AR7051 – AR7051C
ONO
EVIDENCE OF CONFORMITY / DÉCLARATION DE CONFORMITÉ / DECLARACIÓN DE CONFORMIDAD /
DICHIARAZIONE DI CONFORMITA / KONFORMITÄTSERKLÄRUNG / DECLARAÇÃO DE CONFORMIDADE
-The products listed above are in compliance with the safety prescriptions:
x2006/42/EC Machine Directive Safety prescriptions.
x2004/108/EC Electromagnetic compatibility Directive.
x2006/95/EC Low voltage Directive.
x2000/14/EC Noise émission Directive.
xEN 60335-2-41 European Directive.
x2002/95/EC European Directive (RoHS)
-Les produits énumérés ci-dessus sont conformes aux presciptions de sécurité:
xDirective de sécurité de machines 2006/42/CE.
xDirective de compatibilité électromagnétique 2004/108/CE.
xDirective d´équipes de basse tension 2006/95/CE.
xDirective d´émission sonore 2000/14/CE.
xDirective Européenne EN 60335-2-41.
xDirective Européenne 2002/95/CE (RoHS)
-Los productos arriba enumerados se hallan conformes con:
xDirectiva de seguridad de máquinas 2006/42/CE.
xDirectiva de compatibilidad electromagnética 2004/108/CE.
xDirectiva de equipos de baja tensión 2006/95/CE.
xDirectiva de emisión sonora 2000/14/CE.
xDirectiva Europea EN 60335-2-41.
xDirectiva Europea 2002/95/CE (RoHS)
-I prodotti su elencati sono conformi al quanto segue:
xDirettiva sulla sicurezza delle macchine 2006/42/CE.
xDirettiva sulla compatibilità elettromagnetica 2004/108/CE.
xDirettiva apparecchiatura in bassa tensione 2006/95/CE.
xDirettiva sulle emissioni sonore 2000/14/CE.
xDirettiva Europea EN 60335-2-41.
xDirettiva Europea 2002/95/CE (RoHS)
- Die oben angeführten Produkte entsprechen den Sicherheitsbestimmungen:
xRichlinie 2006/42/EWG über die Sicherheit von Maschinen.
xRichtlinie 2004/108/EWG über elektromagnetische Verträglichkeit.
xRichtlinie 2006/95/EWG über die Sicherheit von elektrischen Betriebsmitteln (Niederspannungsrichtlinie).
xRichtlinie 2000/14/EWG über Geräuschemissionen.
xEuropäischen Richtlinie EN 60335-2-41.
xEuropäischen Richtlinie 2002/95/EWG (RoHS)
-Os productos da lista acima estáo conformes as:
xDirectiva de segurança de máquinas 2006/42/CE.
xDirectiva de compatibilidade electromagnética 2004/108/CE.
xDirectiva de equipamentos de baixa tensão 2006/95/CE.
xDirectiva de emissão sonora 2000/14/CE.
xDirectiva Europeia EN 60335-2-41.
xDirectiva Europeia 2002/95/CE (RoHS)
Sign the present conformity evidence/ Signe la présente déclaration/ Firma la presente declaración/ Firma la seguente
dichiarazione/ Unterzeichnet diese Erklärung / Assina a presente declaração:
Polinyà, 07/01/2010 Signature / Firma / Unterschrift / Assinatura
José Manuel Aquilué.
Managing Director of METALAST.
DREAM
POOL
MAGIC
POOL
N REF. DENOMINATION DENOMINACIÓN DESIGNATION BESCHREIBUNG DENOMINAZIONE OMSCHRIJVING DESCRIÇAO
1
157800602G
FILTER PURGUE
ASSEMBLY CONJUNTO PURGA FILTRO ENSEMBLE PURGE FILTRE ABWASSER-FILTER-ELEMENT CONGIUNTO PURGA FILTRO ONTLUCHTINGSSET FILTER CONJUNTO PURGA FILTRO
2
3
19460R0002G
FILTER BODY +
COLLECTOR
FILTER
CUERPO FILTRO +
COLECTOR
FILTRO
FILTRE +
COLLECTEUR
FILTRE
FILTERKÖRPER +
SAMMELBEHÄLTER
FILTER
CORPO FILTRO +
COLLETTORE
FILTRO
FILTERHUIS +
COLLECTOR
FILTER
FILTRO +
COLECTOR
FILTRO
4
24182-1003G
CLOSING BAND
ASSEMBLY CONJUNTO ZUNCHO ENSEMBLE FERMETURE ZWINGEN-ELEMENT CONGIUNTO REGGETTA RINGENSET ANEL
5
200473000
PRESSURE
GAUGE SET CONJUNTO MANÓMETRO ENSEMBLE MANOMÈTRE DRUCKMESSER-ELEMENT CONGIUNTO MANOMETRO MANOMETERSET MANÓMETRO
6
33904G VALVE +"O" RING VÁLVULA +JUNTA VANNE + JOINT VENTIL + O-RING VALVOLA + O RING VENTIEL + O-RING VALVULA + O-RING
7
720R1750057 "O" RING JUNTA TÓRICA JOINT TORIQUE O-RING
8
09089R0002
CONNECTION
HOSE Ø 38 MANGUERA CONEXIÓN Ø 38
TUYAU DE
CONNEXION
Ø 38
VERBINDUNGSSCHLAUCH
Ø 38
MANICOTTO DI
COLLEGAMENTO
Ø 38
AANSLUITSLANG
Ø 38 MANGUEIRA LIGAÇAO Ø 38
9
25470G2000
NUT + PREFILTER
COVER +
"O" RING +
BASKET
TUERCA + TAPA
PREFILTRO +
JUNTA + CESTO
ECROU +
COUVERCLE
PRÈFILTRE +
JOINT + PANIER
VERBINDUNGSSCHAUBEN +
VORFILTERDECKEL +
DICHTUNGSRING +
VORFILTERKORB
VITE + COPERCHIO
PREFILTRO
+ O-RING + CESTO
MOER + TOP
VOORFILTER +
O-RING +
WINKELMANDJE
PORCA + TAMPA
PREFILTRO +
O-RING + CESTO
10
25470G0102
UNION NUT +
UNION + "O" RING
TUERCA MANGUITO +
MACHO UNIÓN +
JUNTA TORICA
ÉCROU RACORDS +
MACHÓN UNIÓN +
JOINT
VERBINDUNGSSCHAUBEN +
SCHLAUCHVERBINDUNG
+ O-RING
VITE MANICOTTO +
PILONE UNIONE
TUBO + O-RING
MOER +
SLANNGAANSLUITIN
G + O-RING
PORCA CACHIMBO +
MACHO UNIÃO
MANGUEIRA + O-RING
11
25470G0105 CAPACITOR CONDENSADOR CONDESATEUR KONDENSATOR CONDENSATORE CONDENSATOR CONDENSADOR
12
25470G
COMPACT 0,4 HP
PUMP BOMBA COMPACT 0,4 CV POMPE COMPACT 0,4 CV COMPACT 0,4 CV PUMPE POMPA COMPACT 0,4 CV COMPACT 0,4 CV POMP BOMBA COMPACT 0,4 CV
0120B008
ACCESSORIES
BAG BOLSA ACCESORIOS SACHET D'ACCESSOIRES BEUTEL MIT ZUBEHÖR SACCHETTO ACCESSORI ZAHJE MET TOEBEHOREN SACO DE ACCESSÓRIOS
www.PiscinasDesmontables.es
www.PiscinasDesmontables.es

INSTALLATION AND MAINTENANCE MANUAL
MANUAL DE INSTALACIÓN Y MANTENIMIENTO
MANUEL D´INSTALLATION ET D´ENTRETIEN
MANUALE DI INSTALLAZIONE E MANUTENZIONE
EINBAU-UND BETRIEBSANLEITUNG
INSTALLATIE EN ODERHOUD HANDLEIDING
MANUAL DE INSTRUÇÕES E MANUTENÇÃO
MONOBLOCK FILTER · FILTRO MONOBLOC · FILTRE MONOBLOC · FILTRO MONOBLOCCO
MONOBLOCK-FILTER · MONOBLOCK FILTER · FILTRO MONOBLOCO
www.gre.es
GRE-0008-00
www.PiscinasDesmontables.es
www.PiscinasDesmontables.es

English - MONOBLOCK FILTER
INSTALLATION AND GENERAL MAINTENANCE MANUAL . . . . . . . . . . . . . . . . . .page 3
Español - FILTRO MONOBLOC
MANUAL DE INSTALACIÓN Y MANTENIMIENTO GENERAL . . . . . . . . . . . . . . .página 11
Français - FILTRE MONOBLOC
MANUEL D’INSTALLATION ET MAINTENANCE GÉNÉRAL . . . . . . . . . . . . . . . . . .page 19
Italiano - FILTRO MONOBLOCCO
MANUALE DI INSTALLAZIONE E MANUTENZIONE GENERALE . . . . . . . . . . . . .pagina 27
Deutsch - MONOBLOCK-FILTER
EINBAU-UND BETRIEBSANLEITUNG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Seite 35
Nederland- MONOBLOCK FILTER
INSTALLATIE EN ODERHOUD HANDLEIDINGL . . . . . . . . . . . . . . . . . . . . . . . .page 44
Portugues -FILTRO MONOBLOCO
MANUAL DE INSTALAÇÃO E MANUTENÇÃO GERAL . . . . . . . . . . . . . . . . . . . .página 52
www.PiscinasDesmontables.es
www.PiscinasDesmontables.es

3
ENGLISH
Installation and General Maintenance Manual - POOL PUMPS
INSTRUCTIONS FILTRE MONOBLOC
Read this manual thoroughly before installing the filter and follow the instructions carefully during installation and use.
Keep this manual for future reference regarding the operation of this equipment.
• All electrical installations should comply with the following standard:
European Low Voltage Directive 2006/95/CE,
EN 60335-2-41, safety of household or similar electrical appliances, particular requirements for pumps.
As such with all rules pertaining to “to the construction of electrical installations within specific confines: swimming
pools and fountains”, or the equivalent standard in force in each region or country.
• The electrical installation should be done by someone qualified in working with electrical equipment. This
equipment is not designed for those with physical, sensory or mental handicap or people lacking in experience,
unless done under supervision or with instructions of use from a person in charge of safety.
• The height of the sand should not exceed 2/3 of the height of the tank.
• The equipment must not be switched on while the pool is being used.
• Do not operate the equipment unless it is properly primed.
• NEVER touch the filter when it is operating if you are wet or have wet hands.
• When handling the filter or valve, DISCONNECT the power supply.
• Make sure that the ground is dry before touching the electrical equipment.
• Do not submerge the equipment or put it in a place where it could be submerged.
• Do not permit children nor adults to sit or lean on the equipment. Children should be supervised to ensure that they
do not play with the equipment.
• If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified
person in order to avoid a hazard.
• The equipment should be connected to a voltage (see data on the pump’s plate), with earth connection, protected
by a residual current device (RCD) having a rated residual operating current not exceeding 30 mA.
• It is essential that you use a multiple disconnection device with a space of at least 3 mm between surfaces to
disconnect the filter from the electrical current.
FIG. POS. NAME
11A 4 functions valve
1 1B 5 functions valve
1 1C 6 functions valve
1 2 Filter
1 3 Monobloc base
1 4 Conection hose valve-pump
1 5 Pump
Some of the equipment's accessories (silica sand, hoses, manometers...) are not included in all models of monoblocs.
1 PACKING COMPONENTS
The equipment which you have just purchased is a special apparatus conceived and designed especially for above ground
swimming pools. As a result of its innovative design and high level of functionality, it provides you with the different components
required to filter water: filter, pump and selector valve in a single unit. The main components of this filter are as follows:
www.PiscinasDesmontables.es
www.PiscinasDesmontables.es

ENGLISH
MONOBLOCK FILTER - Installation and General Maintenance Manual4
REQUIREMENTS FOR CORRECT INSTALLATION
This filter is easy to install and can be assembled by one adult in about 2 hours, taking care to follow the instructions detailed
in this manual correctly. Only the following tools are required to correctly handle the filter components and to install it:
2 BEFORE CONNECTING THE FILTER
LOCATION
Place the filter on a flat, solid surface at a minimum distance of 3.5 meters from the pool (in accordance with standard installation
regulations of electric equipment in swimming pools in force in each region or country) and at the same level as the bottom of the
pool to prevent air from entering the cleansing circuit and to ensure that the filter remains primed (fig. 2). The filter should be
protected from sun and rain, and kept in a sufficiently ventilated area during operation. Never cover it during operation.
In models where pool connection hoses are supplied, these will be 4.5 metres in length. In all cases, check that this length is
sufficient in order to install the apparatus on a flat, solid surface more than 3.5 metres away from the pool. If the hose length
is insufficient, contact your service centre.
When hoses are not supplied with the apparatus, hoses with a minimum length of 4.5 metres should be used which allow the
filtering equipment to be placed on a flat, solid surface more than 3.5 metres away from the pool. This hose set is available
as an optional kit from your vendor.
During the installation process, if in doubt, contact the vendor of the equipment
ASSEMBLY
Once the filter is set in place, proceed as follows:
• Fix the filter to the base. Depending on the monoblock filter (Fig. 0).
• Fix the pump to the base with the screws and washers supplied.
• Place the inner collector correctly on the bottom of the filter (Fig. 9).
• Cover the mouth of the collector situated on the inside of the filter with a plastic protector to make sure sand does not enter (Fig. 4).
• Put the sand inside the filter: The height of the sand should not exceed 2/3 of the height of the tank (Fig.4).
The silica sand lasts for an unlimited period of time. It should only be replaced if lost. Record the reference of the level of
silica sand for future replacement (Fig. 4).
• Remove the remains of sand from the filter opening and take off the protective plastic.
• Put the selector valve with its coupling and secure with the metal band or seal.
• Firmly tighten the screw on the metal band which joins the valve to the filter (fig. 3).
• Connect the (PUMP) and (RETURN) terminals of the selector valve to the corresponding hoses, tightening them firmly with
the clamps (Fig. 5).
NOTE: Check that the hoses allow the filtering equipment to be located and fixed on a flat, solid surface that is more than 3.5
metres from the pool.
• Connect the other end of the suction hose to the skimmer tightening firmly with a clamp. Repeat the same procedure with
the return nozzle terminal and connect the discharge hose.
• Following installation, the first cycle of filter backwash should be performed. In order to do so, follow the instructions in section 5.3.
TASK TOOL ALTERNATIVE TOOL
Tighten the hose flanges 7 mm Stecker screwdriver Philips screwdriver
Tighten the pump screws Open-end or socket wrench Open-end or socket wrench 13
Cut the liner Cutter knife
Protection of collector pipe Piece of plastic Piece of fabric
www.PiscinasDesmontables.es
www.PiscinasDesmontables.es

ENGLISH
Installation and General Maintenance Manual - MONOBLOCK FILTER 5
3 ELECTRICAL CONNECTION
All electrical installations should comply with the following standard:
European Low Voltage Directive 2006/95/CE,
EN 60335-2-41, safety of household or similar electrical appliances, particular requirements for pumps.
As such with all rules pertaining to “to the construction of electrical installations within specific confines: swimming pools and
fountains”, or the equivalent standard in force in each region or country.
The equipment should be connected to a voltage (see data on the pump’s plate)power point, with earth connection, protected
by a residual current device (RCD) having a rated residual operating current not exceeding 30 mA. (Not supplied; available for
purchase in electrical shops).
It is essential that you use a multiple disconnection device with a space of at least 3 mm between surfaces to ensure there is
no current when the equipment is not being used. (Not supplied; available for purchase in electrical shops.)
4 TOP SELECTOR VALVE
VALVE TYPES AND FUNCTIONING
A- 4 function valve: The top selector valve on the filter is used to select the 4 different filter functions: filtration (filter), backwash,
waste and closed.
B- 5 function valve: The top selector valve on the filter is used to select the 5 different filter functions: filter, backwash,rinse,
waste and closed.
C- 6 function valve: The top selector valve on the filter is used to select the 6 different filter functions: filter, backwash,
recirculate, rinse, waste and closed.
To vary the position of the 4 function valve, proceed as follows: (Fig. 6)
• Disconnect the equipment from the mains.
• Loosen the upper triangular knob on the valve by turning it until you can lift the cover of the housing and turn it.
• Turn the cover until the desired setting is aligned with the discharge hose, where the anchorage is, and the rib is
inserted in its housing.
• Re-tighten the knob by turning it, but be careful not to over-tighten so as not to damage the internal components
of the valve.
To vary the position of the 5 function valve / 6 function valve, proceed as follows: (Fig. 7) (Fig. 8)
• Disconnect the equipment from the current.
• Firmly press the upper selector valve, displacing the front rib, until you can turn it.
• Turn the control gently until the front rib is in line with the desired operation.
• Slowly release the control, making sure that the front rib is sitting firmly in its place
ASSEMBLING THE PRESSURE GAUGE
WITHOUT PRESSURE GAUGE 1 2 3
www.PiscinasDesmontables.es
www.PiscinasDesmontables.es

ENGLISH
MONOBLOCK FILTER - Installation and General Maintenance Manual6
5 OPERATION
The operation of this filter is based on the filtration capacity of the silica sand which is inside. The water in the pool is driven by the
filter pump and forced to pass through the silica sand. The sand acts as a filtering element which retains the impurities in the water.
The environment, trees, pollen, insects and frequency of bathing, amongst other factors, determine the dirtiness of the water in the
pool. Depending on these factors, the silica sand in the filter should be cleaned with greater or less frequency (see section 5.3).
To keep the pool water in good condition, use the chemical products recommended by the manufacturer (chlorine, alga
protection, flocculants, etc.).
CHEMICAL PRODUCTS SHOULD NEVER BE PLACED IN THE BASKET OR THROUGH THE FILTER, AS THIS WOULD
DETERIORATE THE MATERIALS OF THE UNIT AND LIMIT ITS EFFICACY.
5.1 PRIMNG THE FILTER
The filter must be correctly primed at all times. If the filter is not primed it means that an air chamber has been created inside which
causes defective circulation of water. This prevents proper filtration of the water by the silica sand and is detrimental to the motor.
The filter may become unprimed for several reasons:
• Starting up a new unit.
• Starting up a unit after an extended period of inactivity.
• Following use of a suction bottom cleaner.
• Air absorbed by the skimmer due to the low level of water in the pool.
• Due to incorrect use of the unit, suction cover or skimmer plug.
When is the filter unprimed?
We can see that the filter is unprimed when:
• The water entering the filter sounds like it is falling freely. This indicates that an air chamber has been created between the
water inlet and the silica sand.
• An excess of air bubbles is released through the return nozzle.
• The bottom cleaner (not supplied) does not operate with suction, and the silica sand remains clean after cleaning.
How can we prime the filter?
• Verify that the suction hose is connected to the skimmer and the passage is clear (the plug is not in place).
• With the valve on the filter position, slightly loosen the drain nut which is beside the pressure gauge, so as the air
accumulated inside the filter can leave.
• When you see that only water is released (for 1 to 2 minutes), re-tighten the nut.
5.2 FILTRATION
NEVER HANDLE THE VALVE WHILE THE MOTOR IS RUNNING
Carry out a wash of the sand before the first filtration. (Part 5.3)
The valve should be in the filter position (FILTER). The service life of the filter will be longer if the periods of continuous operation do not exceed 4
hours.Theneedfordailyfiltrationisdeterminedbythevolumeofwaterinyourpoolinm3inrelationtothem3/hfilterflowrateforawatertemperature
of approximately 21ºC and placed 3.5 m from the pool. Leave the motor at a standstill for at least 2 h between each 4 h period of operation.
Pool volume in m3= Hours required Example: 42 m3=7.63 hours
Filter flow rate in m3/h 5.5 m3/h 2 cycles of 4 hours with a break of 2 hours
In the initial filtration treatment it is important to leave the filter at a standstill for the periods indicated. It is recommended
that you increase the amount of time in ratio to any temperature rise in the pool.
www.PiscinasDesmontables.es
www.PiscinasDesmontables.es

ENGLISH
Installation and General Maintenance Manual - MONOBLOCK FILTER 7
5.3 FILTER BACKWASH
The backwash process cleans the silica sand from inside the filter. This is achieved by reversing the direction of water circulation
with the top selector valve. This process should be done regularly. For this purpose you should observe several factors which
indicate the dirtiness of the sand:
• A decrease in the return flow rate is detected, after checking that the pump is well primed.
• Pressure gauge indicates that there is excess pressure (> 1.2 bar or needle pointing between yellow and red, or on red).
To clean the filter, proceed as follows according to valve type:
4 function valve: (Fig. 6)
• Disconnect the filter from the mains. Never move the selector valve while the motor is running.
• Loosen the upper triangular knob on the valve until you can lift the cover and turn it (Fig.6). Place the valve on the backwash
setting, reinserting the cover in its housing and re-tightening the knob by turning it. Do not over-tighten the knob so as to
avoid damaging the valve.
• Connect a hose to the valve waste outlet from the valve and direct the other end of the hose to a drain or sewer.
• Run the filter for approximately 2 minutes (until impurities no longer run out with the water).
• Stop the filter and leave it to rest for 2 minutes so as to let the silica settle and stop it from running out into the pool.
• Reset the valve to the desired setting (filtration or closed) (Fig. 6) and remove the hose from the drain outlet.
For 5 and 6 function valves: (Fig. 7 and Fig.8)
• Disconnect the filter from the mains. Never move the selector valve while the motor is running.
• Firmly press the upper selector valve, displacing the front rib, until you can turn it (Fig. 7).
• Turn the control gently until the front rib is in line with the backwash operation (Fig. 7).
• Connect a hose to the valve waste outlet from the valve and direct the other end of the hose to a drain or sewer.
• Run the filter for approximately 2 minutes (until impurities no longer run out with the water). In the valve model fig.8, this
can be seen through the transparent window on the side.
• Stop the equipment.
• Put the valve in the rinse position and connect the filter for a few seconds (Fig. 7).
• Stop the equipment, put it in the desired filter position (Fig. 7) and remove the hose from the waste position, if you desire.
5.4 DRAINING THE POOL
The following accesory is aviable to help drain the pool:Portable submersible pump AR2071.
The filter allows you to drain nearly the entire pool after the bathing season has ended. In order to do so, you should set the
top selector valve on the waste setting (Fig. 6) (Fig. 7) without plugging in the filter and connect a hose to the valve waste
outlet and direct the other end to the drain or sewer.
Depending on the skimmer model (see specific manual), proceed as follows:
5.4.1 With wall skimmer (for Dream Pool swimming pools):
• Remove the inner basket from the skimmer and cover the suction inlet with the plug supplied for this purpose.
• Disconnect the suction hose from the skimmer inlet. Loosen the clamp which secures the hose, supporting it so that no water
leaks and it loses priming.
• Remove the hose, covering the end so it remains primed, and submerge it immediately in the pool.
• Weigh down the end of the suction hose with a heavy object which will not damage the liner so that it is forced to sink to
the bottom of the pool.
• Start up the pump and drain the pool. Remember that the filter will not fully drain the pool. When a few centimetres of
water are left and the pump no longer sucks in water, turn it off.
• If you are going to refill the pool with water, first manually remove the remaining water without damaging the liner.
• If you are going to disassemble the pool, you can fold the bag with the remaining water in the centre and after removing
the plate, unfold the bag to empty it completely. This operation should only be done when you are disassembling the pool.
www.PiscinasDesmontables.es
www.PiscinasDesmontables.es

ENGLISH
MONOBLOCK FILTER - Installation and General Maintenance Manual8
5.4.2. With self-supporting skimmer (for Magic Pool swimming pools):
Aside from the drain included within the pool, you can use the filter system to empty it:
• Raise the self-supporting skimmer until it is hanging outside the pool, to prevent water from entering the skimmer.
• Disconnect the suction hose from the skimmer inlet by the outer part of the pool wall. Loosen the clamp which secures the
hose carefully so that the liner is not damaged. Hold the hose so that no water leaks and it loses priming.
• Remove the hose, covering the end so it remains primed, and submerge it immediately in the pool.
• Weigh down the end of the suction hose of the skimmer inlet with a heavy object which will not damage the liner so that it
is forced to sink to the bottom of the pool.
• Start up the pump and drain the pool. Remember that the filter will not fully drain the pool. When the pump no longer sucks
in water, turn it off.
• If you are going to refill the pool with water, first remove the remaining water through the drain without damaging the pool.
THE HOSE SHOULD NOT CONTINUE TO APPLY SUCTION TO THE BOTTOM OF THE POOL LINER. THE PUMP MAY BE
SERIOUSLY DAMAGED IF IT OPERATES WITHOUT WATER CIRCULATION OR MAY DAMAGE THE LINER.
5.5 CLEANING THE BOTTOM OF THE POOL
In order to clean the bottom of the pool, use the pump filter with one of the following accessories: “Riñón” bottom cleaner /
AR-206, “Oval” bottom cleaner / AR-207 (you will also need a Ø38 mm hose / AR-210 and the pole / AR-102).
For any enquiries on warranties or after-sales service, please contact the vendor.
A hose which extends beyond the length required to reach all points of the pool is more difficult to use. Cut off the section of
the hose which is not needed. Check that the rubber terminals conserve their seal.
Priming the bottom cleaner hose:
Insert the bottom cleaner into the pool vertically, with the pole and the hose connected. Let it fill with water and keep the rest
of the hose outside of the water. Continue to insert the hose in the water slowly by 50 cm sections which should be submerged
at the same time as they are completely filled with water. Proceed up until the end, when the entire hose is filled with water
and submerged. If the hose is not fully primed, the bottom cleaner will not perform suction and the cleansing unit may be
damaged if it is forced to operate when it is empty.
Depending on the skimmer model (see specific manual), proceed as follows:
5.5.1. With wall skimmer (Dream Pool swimming pools):
• Place the suction cover accessory inside the skimmer with the inlet facing upwards, without removing the basket.
• Prime the hose.
• Pass the end of the hose through the gate of the skimmer from the INSIDE OF THE POOL, ensuring that no air gets in. Connect
it to the inlet of the suction cover, pressing it at a slant to create the join. Then insert it horizontally, introducing the hose
further. Pay attention not to damage the skimmer gate during this operation.
• The water level of the skimmer should be at a maximum and above the join between the cover and the hose to prevent air
from entering.
• Run the pump in the FILTER position and clean the bottom of the pool.
5.5.2. With self-supporting skimmer (Magic Pool swimming pools):
• Remove the upper floating ring from the skimmer and without removing the preliminary filtration basket, place the suction
cover accessory in the upper part of the skimmer with the inlet facing upwards and immerse the skimmer inside the pool
sufficiently to ensure that the suction cover does not take in air.
• Prime the hose.
• Ensuring that no air enters, connect the hose to the suction cover inlet. The join between the hose and the cover should always
be submerged to prevent air from entering.
• Run the pump and clean the bottom of the pool.
www.PiscinasDesmontables.es
www.PiscinasDesmontables.es