Great American Recreation Home Power Hockey Table User manual

Power Hockey Side Score (non-coin)
Setup & Assembly Instructions
20 Providence Pike
North Smithfield, RI 02896
800-831-2011 • (f) 401-463-6673
www.GreatAmericanRec.com
[e-mail]

Thank You for purchasing the Great American Recreation Home Power Hockey Table.
This table is a home version of our commercial grade Power Hockey Table. It is designed
to withstand many thousands of plays in a commercial environment (i.e. bar, video
game/amusement center, etc.). We are confident that it will provide years of enjoyment in
your home.
Parts List
The following parts should be included with the Home Power Hockey Table:
4 Legs with attached levelers (located inside trap door in base)
16 1 1/2” x 3/8” #16 bolts (attached to inside of trap door)
10 Keys (amount may vary)
2 Mallets
1 Puck
1 Score Panel
4 1/4” #20 bolts

Setup Instructions
1. Locate key taped to Home Power Hockey Table playing surface.
2. Open trap door on the bottom of the H.P.H. Table.
3. Remove 4 legs with levelers and a bag of (16) bolts attached to the inside of the trap
door.
4. Attach legs to bottom of table using (16) 1 1/4” x 3/8” #16 bolts. (See Figure 1)
5. Stand table upright.
6. Open Power Supply Access Door (see Figure 2).
7. Locate bag stapled to door containing (4) 1/4” #20 bolts.
8. Using those bolts, attach Score Panel to side of table with taped wire.
9. Connect Wire from table to connector marked “Interface” on the back of the Score
Panel.
NOTE: Make sure the notch on the wire harness faces the center of the circuit board.
Front View of Home Power Hockey Table
FIGURE 1
1 1/4” x 3/8” #16 Bolt
Trap Door for legs
(on bottom of table)
Puck Drop Access Door
Legs
Wire from table
Score Panel
1/4” #20 bolts
Locks

Setting up the Game Options
The Home Power Hockey game has the following factory set defaults:
1 push of the credit button allows 1 game with a maximum game time of 5 minutes.
Multiple pushes allows multiple credits to accumulate.
To change these settings, you must change the DIP switches located on the Logic
Board which is behind the Power Supply Access Door. Refer the DIP switch setting sheet
attached to the inside of the Power Supply Access Door (see Figure 2).
Puck Drop Access Doors
Locate the Puck Drop Access Door on either end of the H.P.H. Table. These doors
can be opened, using the keys provided, to remove the any foreign objects which may fall
into or obstruct the puck in the Return Chute (see Figure 1).
FIGURE 2
Credit Button
Power Supply Access Door
Side View of Home Power Hockey Table
Score Panel
Power On/Off Switch
(Inside of Door)

L E F T S C O R E S W IT C H
C O IN S W IT C H R IG H T
S C O R E S W IT C H
Power Hockey Wiring Diagram
Rev. 11/4/ 98

GA
REAT MERICANRECREATIONEQUIPMENT, INC.
110POWERSUPPLYBOXDIAGRAM

DIP Switch Settings
(If Your Hockey has a YELLOW LOGIC BOARD)
AH2004(V1.05)
Description
Value
DIP SwitchNumber 1
1
2
3
4
5
6
7
8
End
Of Play
Score
6
0
0
7*
1
0
8
0
1
9
1
1
End
Of Play
Timer
(Minutes)
6
0
0
9*
1
0
12
0
1
15
1
1
Coins
Per
Play
If using a slide
mech this is set
to one and the slide
determines the
pricing.
1*
0
0
0
2
1
0
0
3
0
1
0
4
1
1
0
5
0
0
1
6
1
0
1
7
0
1
1
8
1
1
1
Coin Slide
or
DropMech
CoinSlide*
0
DropMech
1
* Denotes factory Setting

AH2004(V1.05)
Description
Value
DIP SW 2
1
2
3
4
DBA
Factor
What should the pulses
out of the DBA be
divided or
multiplied by
to equal one
coin.
1*
0
0
0
2
1
0
0
3
0
1
0
4
1
1
0
5
0
0
1
6
1
0
1
7
0
1
1
8
1
1
1
Multiply or Divide
Pulses
MULTIPLY*
0
DIVIDE
1
* Denotes Factory Setting
Connector Pin Outs Pin
#1 is left hand pin facing connector and has square solder pad.
Connector
Pin#
Function
J2
1
+12VDC to DBA
(DBA Port)
2
GND to DBA
3
N/C (Key)
4
Coin 2 Input from DBA
5
+5VDC for DBA EN+
6
GND for DBA EN-
J3
1
+12VDC to Sound Board
(Sound Port)
2
TXD to Sound Board
3
GND to Sound Board
4
RXD from Sound Board

Jl Edge Connector Pin Out
Top (Parts Side)
Bottom (Solder Side)
AC IN 1
1
2
N/C
AC IN 1
3
4
Coin 2 Switch
AC IN 2
5
6
DC Ground
AC IN 2
7
8
DC Ground
N/C
9
10
Start Switch(N/U)
DC Ground
11
12
Left Puck Switch
DC Ground
13
14
Right Puck Switch
DC Ground
15
16
Coin 1 Switch
+12VDC
17
18
Credit Lamp(N/U)
+12VDC
19
20
Motor Relay
+12VDC
21
22
Counter 1
+12VDC
23
24
N/C
Counter 2(N/U)
25
26
+5VDC
KEY
27
28
KEY
DC Ground
29
30
N/C

Puck Lockout Soleniod Installation
1. Remove the side covers from the overhead score unit by removing two phillip screws on
each end cap.
2. Disconnect the 3 wire connections for the overhead score unit.
3. Remove overhead score unit by removing 4 bolts in the side mounting bracket.
4. Open the side door and unplug the black blower cord (very important) which is located
on the side of the power supply unit.
5. Remove all screws around the top outside edge of the table (located below the top rails)
and remove top rails and play field.
6. At each goal end, inside the table, are the puck lock out solenoids. Remove the 2 bolts
and 3 wires (black, white & green). Before removing wires, please note the position of
each wire for re-assembly
1. Then install new solenoids and reassemble table using the steps above as a guide.